SHOWER TRAY INSTALLATION & CARE GUIDE SB-AZ03CD SB-AZ04CD SB-AZ03LD SB-AZ04LD SB-AZ03RD SB-AZ04RD SB-AZ01NO SB-AZ01RO SB-AZ022L SB-AZ022R SB-AZ02XX For any questions or assistance simply call 1-844-44-ANZZI or visit us at www.ANZZI.
SINGLE THRESHOLD SHOWER BASE Center Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) SB-AZ03CD SB-AZ04CD 32"×60" 36"×60" 32" 36" 60" 16" 15" 30" 60" 30" W W1 11 D1 D SINGLE THRESHOLD SHOWER BASE Left-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) SB-AZ03LD SB-AZ04LD 32"×60" 36"×60" 32" 36" 60" 60" 15" 18" 12" 12" 3
W W1 D1 D SINGLE THRESHOLD SHOWER BASE Right-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) SB-AZ03RD SB-AZ04RD 32"×60" 36"×60" 32" 36" 60" 60" 16" 18" 12" 12" 4
W W1 D1 D NEO ANGLE SHOWER BASE MODEL SPECIFICATION W (in) A (in) B (in) C (in) 36"×36" 36" 16 1/2" 27" 12" SB-AZ01NO W C C A W B A 5
QUARTER ROUND SHOWER BASE MODEL SPECIFICATION W (in) C (in) R (in) SB-AZ01RO 32"×32" 32" 12" 22" W C C W R 6
DOUBLE THRESHOLD SHOWER BASE Center Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in) SB-AZ02XX SB-AZ022L SB-AZ022R 32"×48" 32"×48" 32"×48" 32" 32" 48" 48" 32" 15" 15" 24" 24" 24" 48" 15" W W1 D1 D Shower Base Cross Section Diagram Shower Base Cement board Finished Wall (2"×4") Stud Mortar Drain 2"PVC Waste Pipe 7
Shower Base Installation - Preparation 1. Ensure that the floor and the studs are at right angles. Provide a 5”×5” opening in the subfloor for the drain. The 2” PVC waste pipe should extend above the surface of the sub-floor according to the drain installation instructions and the height of the Shower base. Refer to the product drawings and tables in these installation instructions for the drain location. 90° 90° 90° See Fig. 1 and Fig. 2 for details.
2. Install the shower drain (NOT INCLUDED) according to the drain installation manual (supplied with the drain). See Fig. 3 for example Fig. 3 3. Place the tray into the designated position so that the Drain Body drops around the Drain Pipe and butt the Shower Base up against the studs. See Fig. 4 for details. Lower the base over the drain pipe and set it into place against the studs. Fig.
4. Level the tray and place marks on the studs above the upper edge of the tile flange. See Fig. 5 for details. Level base in two directions Fig. 5 5. Mix the bedding material (Mortar, cement-sand mix, etc.) Concrete or plaster is not recommended. Apply enough bedding material to support the entire bottom of the shower base. This will add additional stability and prevent the base from shifting position. See Fig. 6 for details. Mortar Fig.
6. After the bedding material has been poured and before it sets, place the shower base into the position with the drain assembly sliding over the PVC waste pipe. It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base. Ensure that the base is level in all directions.
Fig. 9 Product maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth. Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup.
