Ceiling Fan
Please contact us with following information: 1. Screen shot of your order page, including product picture, name and order ID number. 2. Problem details with pictures / short video if possible.
Packing List ① ⑥ ② ③ ⑦ ④ ⑤ Name QTY Name QTY ① Mounting Bracket 1 ⑤ Light Shade 1 ② Canopy 1 ⑥ Remote Controller 1 ③ Downrod 2 ⑦ Hardware Bag ④ Adapter Cover 1 1 Set NOTE: 1. Light frame ⑤ style may be different from the diagram. 2. Remote control requires Alkaline Battery 23A 12V x 1pcs (not included).
Safety Rules 1. Be sure the power to the wires you are working on is disconnected, either the fuse is removed or the circuit breaker is turned off. Turning the power off using the light switch is not sufficient to prevent electrical shock. 2. A qualified licensed electrician is required for the installation. 3. The outlet box and support structure must be securely mounted and capable of reliably /supporting a minimum of 70 pounds.
1. Installation Preparation Tools You Need Ladder Wire Strippers Pliers Screwdrivers Power Drill (optional) Drill Bit (optional) If mounting to a support structure, you will also need the optional tools. What to Expect with Your Installation You may need a friend to help you. 30 inches from blade tip to nearest wall or obstruction Ceiling angles greater than 22° will require an Angled Mounting Kit.
4. Installing the Fan NOTE: This ceiling fan is supplied with two types of hanging downrods: 1. The short downrod for "close-to and flat ceiling" installation (less than 9 feet). 2. The long downrod for high or angled ceiling less than 22°. 3. Please contact us if you need longer downrod or angled ceiling greater than 22°. Outlet box Flat washer Mounting bracket Hook Power Wire 1. Installing the Bracket Mounting screw (supplied with the outlet box) Fig. 1 Step 1.
5. Wiring NOTE: THIS FAN ONLY NEEDS ONE SET OF INPUT WIRES (black, white and ground wire). Both of the fan and lights will be controlled by the remote controller. The wall switch is not able to control the fixture full functionally. THIS FAN CAN ONLY BE CONNECTED ONTO ON/OFF SWITCH IF YOU HAVE ONE, NOT SUITABLE FOR DIMMAER SWITCH. Step 1. Connect the fan black wire to your house live wire, white wire to your neutral wire, yellow/green wire from the downrod to your ground wire. Step 2.
6. Installing Bulb 1. Install light bulbs (E12 x 4, Max. 40W each, LED recommended).
Remote Control Instructions ① ② ⑥ ⑦ ③ ④ ⑤ ⑧ ⑨ NOTE: Please insert a alkaline battery before using. 23A 12V x 1pcs (not included) ①②⑥: Turn on the fan, "LOW" / "MED" / "HI" for fan speeds. ⑦: Turn on/off the lights. ③: Turn off the fan. ④⑤⑧⑨: "1H" / "2H" / "4H" / "8H" for timing the fan REMOTE SIGNAL PAIRING: If the remote control looses signal of the fan, turn off the power from wall switch, then turn it on, press ⑥ and ⑦ buttons at the same time immediately for around 3 seconds then it's down.
Trouble Shooting 1. Fan doesn't work • Make sure the fixture is connected to an ON/OFF wall switch, not dimmer switch. • Check the remote control battery (not included in this package). • Check the circuit breaker to ensure the power is on. • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram. 2. Bulbs Do Not Light Up / Flicker / Noisy Operation • Make sure the fixture is connected to an ON/OFF wall switch, not dimmer switch.
Clean And Care To clean, wipe fixture with soft cloth. Spray from chemical cleaners can discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture. Ordering Parts Keep this manual for future reference, and in case replacement parts are needed. Available parts can be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
"We followed the light to a brighter and warmer place.
