Murphy bed WF296210AAE ，WF296211AAE Assembly Instructions - Please keep for future reference WF296212AAE ，WF296217AAE Dimensions Three people are required to assemble and move this model. Width - 80inch Depth - 19.
Assembly Instructions 28 28 27 8 27 7 9 11 26 6 25 13 24 5 23 10 12 4 1 2 2 3 16 15 15 19 14 21 17 18 22 20
Part List Hardware list：WF296210AAE 10 11 1 PC 15 1 PC 16 2 PCS 20 1 PC 21 1 PC 1 PC 22 1 PC 14 18 17 1 PC 1 PC 13 12 1 PC 19 1 PC 1 PC X 1 PC 13 PCS Part List Hardware list：WF296211AAE 3 9 1 PC 26 1 PC 23 1 PC 25 24 1 PC 1 PC 1 PC
Part List Hardware list：WF296212AAE 1 2 1 PC 2 PCS 8 7 1 PC 5 4 1 PC 1 PC 28 27 1 PC 6 2 PCS 2 PCS 1 PC
Using Camlocks Step 1 Connect the male camlock as diected in the assembly instructions using a scewdriver . 1 Step 2 DO NOT OVER TIGHTEN. NE PAS SERRER EXCESSIVEMENT. 2 Push the male camlock into the entry hole. 4 Step 3 3 Step 4 Insert the femle camlock as shown in the instruction. Turn the female camlock clockwise with a screwdriver . Note：ensure that the arrow on the top of the camlock points towards the entry hole for the male camlock .
Part List Hardware list：WF296210AAE Please check you have all the panels listed below Note: The quantitie below are the correcet amount to complete the assembly. In some cases more fittings may be supplied than are required. A B C Male Camlock x 28 Female Camlock x 28 Dowel x 32 D E F 6*50mm Screw x 26 Magnetic bump x 2 Hex Key M4 x 1 G H Expansion screw x 6 I MATTRESS SUPPORT x 2 J Handle & Fixings x 2 K L Fastener x 2 Nut M5 x 2 Ø20 Sticker x 28 M N O Nylon washer（19*1.
Assembly Instructions Step 1 A Ax2 C Cx4 A C 1 A C 2 C C 2 Step 2 B Bx2 1 2 3 1 B B 2 2
Assembly Instructions Step 3 A Ax8 C Cx6 C A C A A A A A C 4 A A C C C Step 4 A Ax4 C C C Cx6 A C 6 A C 5 A C C A
Assembly Instructions Step 5 B B x 12 B 6 B B B 2 1 B B B 5 B B 2 4 B B B 1 3 2 Step 6 C C x 12 C C C F F Fx2 C C C 7 C F C C 8 1. C C C F 2.
Assembly Instructions Step 7 D Dx4 E Ex1 7 D E 8 D D D Step 8 N U N x 16 U x 16 v vx1 11 10 N 13 U 12 V
Assembly Instructions Step 9 D D x 11 E 7 Ex1 8 D E 5 D D 10 D D D D 4 D D D D Step 10 D D x 11 E 7 Ex1 10 8 D E 5 D 4 11 D D D D D D D D D
Assembly Instructions Step 11 C Cx4 C C 10 C 11 C Step 12 A A A x 14 A A A A A A A 9 A A A A A A 3
Assembly Instructions Step 13 9 B B B B 3 B B 7 10 B B B B B 24 B 11 B x 14 B B B Step 14 1 3 2 WALL G Gx6 G G G G G G Three people are required to assemble and move this model.
Assembly Instructions Step 15 M Mx6 M 1 M These hardware are from Wardrobe 1 M M 7 M M Step 16 Two people are required to assemble and move this model.
Assembly Instructions Step 17 15 T T 15 14 T Tx4 Step 18 H T T H 15 16 15 14 H T 37 Tx4 H Hx2
Assembly Instructions Step 19 make sure the tube with mattress stopper holes is in the head position and the tube without any holes are in the foot part.
Assembly Instructions Step 21 T T x 24 T T T T T T T T T T T T 26 T T T T 25 T T 24 T T 23 T T T T T Step 22 19 26 21 25 24 P 18 23 O N 18 20 N 20 O N Nx4 P Ox2 Px1
Assembly Instructions Step 23 20 23 24 25 26 22 22 21 20 Q E Q E Qx4 Q Ex1 Step 24 O S Ox2 WELL SCREW THE 2 ENDS OF THE CYLINDERS S Sx2 23 24 25 26 P Do not release the cykinders until finished the instation O
Assembly Instructions Step 25 Three people are required to assemble and move this model. Important/Importante 1. Place the bearings equal on each side before fixing them up. 2. Well positioning the bearing support in such a way as to lock. 3. Tighten strongly the bearing support.
Assembly Instructions Step 26 Three people are required to assemble and move this model.
Assembly Instructions Step 28 23 24 25 26 Important The fixed cykinder metal could cut off with scissors Take note that after the installation of the pistons, it will be very difficult to open the bed. Continue the steps until the end, put the mattress on, and the bed will open without effort.
Assembly Instructions Step 30 W X W W W x 26 X X x 13 Step 31 M Mx2 M M M Please open the leg before completely lower the bed.
Assembly Instructions Step 32 F Fx2 1. F Bed Board Laminates 2. F F Bed Board Important Rotate the leg towards the interior when close the door Step 33 L L x 34 1 2 3 Assembly is complete.
Use cykinder metal(Z) to remove cykinders Step 1 1.Customer could use Z to remove cykinders when the bed need to be moved or uninstalled 2.Loosen the screwof the cykinders Step 2 1. Y 3. 2.
