INSTALLATION AND OPERATION MANUAL MODEL 2664 MODEL 2934 MODEL 3572 MODEL 2709 MODEL 2935 MODEL 3573 MODEL 2711 MODEL 2938 MODEL 3574 MODEL 2742 MODEL 2939 MODEL 3575 MODEL 2748 MODEL 2940 MODEL 3581 MODEL 2806 MODEL 2941 MODEL 3582 MODEL 2903 MODEL 2942 MODEL 3583 MODEL 2908 MODEL 2943 MODEL 3584 MODEL 2932 MODEL 2944 MODEL 6060 MODEL 2933 MODEL 2945 MODEL 7236 MODEL 3571 BATHTUBS, WHIRLPOOLS, AIR BATHS AND COMBINATION TUBS WITH OPTIONAL CHROMATHERAPY THANK YOU...
TABLE OF CONTENTS: Cover................................................................................................Page 1 Table of Contents..............................................................................Page 2 Safety Instructions Notice.................................................................Page 3 Installation, Framing and Post Installation Clean-Up Instructions.......................................................................
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS! ! WARNING: Risk of personal injury. Do not permit children to use this bathtub without adult supervision. Never drop or insert any object into any opening. Do not operate this unit without the guard over the suction fitting. ! WARNING: Risk of electric shock. Do not permit electrical appliances near any bathtub when bathtub contains water. ! WARNING: Risk of hyperthermia and possible drowning.
Installation and Framing Instructions Each bath arrives ready for installation, completely equipped with the pump/blower electronics and plumbing necessary for operation. However, a drain/overflow kit is required for each bath and it is not included. The variety of installations for this bath may require framing procedures other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper, plumb, and square. ! Remove the bath from the carton.
ROUGH-IN REFERENCES FOR RECESS TYPE INSTALLATIONS C D 12" (305 mm) W E NOTE: FRONT EDGE OF BATH MUST BE SUPPORTED BY STUD WALL OR AMERICAN STANDARD APRON KIT LEVELING STRINGERS 24" (610 mm) ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE MOTOR. ALLOW OPEN FRAMING ON PUMP/MOTOR END FOR SERVICE. ACCESS PANELS NOT REQUIRED FOR BATH TUBS UNLESS AN ACCESS OPENING OF AT LEAST 12" x 24" (305 x 610mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
ROUGH-IN REFERENCES FOR PIER TYPE INSTALLATIONS AS DESIRED F CUTOUT G CUTOUT C 12" (305 mm) AS DESIRED MOUNTING SURFACE WATERPROOF SEALANT BATH 24" (610 mm) ACCESS PANEL MUST BE LOCATED ON THE SAME SIDE AS THE MOTOR. ALLOW OPEN FRAMING ON PUMP/MOTOR END FOR SERVICE. ACCESS PANELS NOT REQUIRED FOR BATH TUBS UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
SPECIFICATIONS: L W J H C SIDE VIEW A END VIEW B DRAIN / OVERFLOW GENERAL SPECIFICATIONS FOR WHIRLPOOLS AND BATH TUBS Description Dimensions L-W-H Drain / Overflow Height to Underside of Deck: C Cut Out Pier GxF Rough-In Recess ExD Tub Edge to Centerline Overflow: J Weight with Water / Floor Loading Product Weight Gallon to Overflow 2664 Scala Corner L 83-1/2" (2121mm) W 63-3/4" (1619mm) H 19-3/4" (502mm) A 16" (406mm) B 13-1/4" (337mm) C 18-1/4" (464mm) Template Provided N/A 6-3/8
ROUGH-IN REFERENCES MODEL SERIES 2664 I AT 42-1/2" (1080mm) 63-1/2" (1600mm) N C LO G IN ) " m) 05m TT m 60 4m 5 ) FI 79m 1 ( m D 52 4" E x2 4m / (1 D 2 1 4 N (7 E (6 59 M " 2" M 11 1/ O x C 28 E 2" R -1/ 2 m 64-1/4" (1632mm) 63-3/4" (1619mm) O ) 1" (25mm) INTEGRAL TILE FLANGE (2) SIDES 10" x 10" (254mm x 254mm) DRAIN OUTLET CUTOUT 21-3/4" (552mm) " /8 ) -3 mm 3 5 56 3 (1 8-1/2" (216mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS " /2 ) -1 mm 0 3 75 (7 3/4"(19mm) CUTOUT DIMENSION 1
ROUGH-IN REFERENCES MODEL SERIES 2711 72" (1829mm) OUTLINE OF CUTOUT 70-1/2" X 46-1/2" (1791 X 1181mm) 36-1/2" (927mm) 4" (102mm) 12" (305mm) C/L OF DRAIN 9" x 14" (229 x 356mm) FLOOR CUTOUT 48" (1219mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS RECOMMENDED FITTING LOCATION 2-1/2" X 11" GRAB BAR FITTING AREA OPTIONAL DECK FITTING AREA MODEL SERIES 2908 66" (1676mm) 13" (330mm) 18" (457mm) 36" (914mm) 9" X 12" (229 x 305mm) FLOOR CUTOUT 2-1/2" REF.
ROUGH-IN REFERENCES MODEL SERIES 2806 72" (1829mm) 11" (279mm) 18" (457mm) 9" x 13" (229 x 330mm) FLOOR CUTOUT 35-3/4" (908mm) INTEGRAL FITTING DECK 5-1/2" (140mm) C/L OF DRAIN OVERFLOW PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT MODEL SERIES 2903 60" (1524mm) 9-1/2" (241mm) 4-1/4" (1073mm) OUTLINE OF CUTOUT - USE TEMPLATE 12" (305mm) X 9"(229mm) CUTOUT IN FLOOR FOR DRAIN 21-1/8" (537mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS 3" (76mm) CL OF DRAIN OUT
ROUGH-IN REFERENCES MODEL SERIES 2742 4" (102mm) 13-1/4" (337mm) 71-1/2" (1816mm) 35-3/4" (908mm) INTEGRAL FITTING DECK 3" x 14" (76 x 356mm) C/L OF DRAIN OUTLET 3" (76mm) EDGE OF FLOOR CUTOUT 41-3/4" (1060mm) FLOOR CUTOUT 5" X 15" (127 X 381mm) 26-3/4" (679mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS 3/4" (19mm) OUTLINE OF CUTOUT 70" X 40-1/4" (1778 X 1022mm) MODEL SERIES 2748 59-1/2" (1511mm) INTEGRAL FITTING DECK 3" X 14" (76 X 356mm) 29-7/8" (759mm) 14-1/2" (368mm) FLOOR CUT
ROUGH-IN REFERENCES MODEL SERIES 6060 76-3/4" REF.
SPECIFICATIONS: L W J H SIDE VIEW C A END VIEW B DRAIN / OVERFLOW GENERAL SPECIFICATIONS FOR STUDIO 5' X 32" WHIRLPOOLS AND BATH TUBS Dimensions L-W-H Height to Underside of Deck: C Cut Out Pier GxF A 17-3/4" (451mm) B 10-3/4" (273mm) C 21-7/8" (556mm) 58" (1473mm) x 30" (762mm) L 59-3/4" (1518mm) W 31-3/4" (806mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 10-7/8" (276mm) C 20-1/2" (521mm) 4" L 60" (1524mm) W 32" (813mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 11" (279mm) N/A L 60" (1524mm)
SPECIFICATIONS: L W J H SIDE VIEW C A END VIEW DRAIN / OVERFLOW B GENERAL SPECIFICATIONS FOR STUDIO 5' X 36" WHIRLPOOLS AND BATH TUBS Dimensions L-W-H Height to Underside of Deck: C Cut Out Pier GxF A 17-3/4" (451mm) B 10-3/4" (273mm) C 21-7/8" (556mm) 58" (1473mm) x 34" (864mm) L 59-3/4" (1518mm) W 35-3/4" (908mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 10-7/8" (276mm) C 20-1/2" (521mm) 4" L 60" (1524mm) W 36" (914mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 11" (279mm) N/A L 60" (1524mm)
SPECIFICATIONS: L W J H SIDE VIEW C A END VIEW DRAIN / OVERFLOW B GENERAL SPECIFICATIONS FOR STUDIO 5-1/2' X 36" WHIRLPOOLS AND BATH TUBS Dimensions L-W-H Height to Underside of Deck: C Cut Out Pier GxF A 17-3/4" (451mm) B 10-3/4" (273mm) C 21-7/8" (556mm) 64" (1626mm) x 34" (864mm) L 65-3/4" (1670mm) W 35-3/4" (908mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 10-7/8" (276mm) C 20-1/2" (521mm) 4" L 66" (1676mm) W 36" (914mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 11" (279mm) N/A L 66" (167
SPECIFICATIONS: L W J H SIDE VIEW C A END VIEW DRAIN / OVERFLOW B GENERAL SPECIFICATIONS FOR STUDIO 6' X 36" WHIRLPOOLS AND BATH TUBS Dimensions L-W-H Height to Underside of Deck: C Cut Out Pier GxF A 17-3/4" (451mm) B 10-3/4" (273mm) C 21-7/8" (556mm) 70" (1778mm) x 34" (864mm) L 71-3/4" (1822mm) W 35-3/4" (908mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 10-7/8" (276mm) C 20-1/2" (521mm) 4" L 72" (1829mm) W 36" (914mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 11" (279mm) N/A L 72" (1829mm)
SPECIFICATIONS: L W J H SIDE VIEW C A END VIEW B DRAIN / OVERFLOW GENERAL SPECIFICATIONS FOR STUDIO 6' X 42" WHIRLPOOLS AND BATH TUBS Dimensions L-W-H Height to Underside of Deck: C Cut Out Pier GxF A 17-3/4" (451mm) B 10-3/4" (273mm) C 21-7/8" (556mm) 70" (1778mm) x 40" (1016mm) L 71-3/4" (1822mm) W 41-3/4" (1060mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 10-7/8" (276mm) C 20-1/2" (521mm) 4" L 72" (1829mm) W 42" (1067mm) H 22-1/2" (572mm) A 17-3/4" (451mm) B 11" (279mm) N/A L 72" (1829
SPECIFICATIONS: L W J H SIDE VIEW C A END VIEW B DRAIN / OVERFLOW GENERAL SPECIFICATIONS FOR STUDIO CORNER WHIRLPOOLS AND BATH TUBS Description Deck Trim Dimensions L-W-H Drain / Overflow Height to Underside of Deck: C Cut Out Pier GxF Rough-In Recess ExD Tub Edge to Centerline Overflow: J Weight with Water / Floor Loading 2944 Studio Corner Zero (5/8") L 83-15/16" (2132mm) W 61-3/8" (1559mm) H 21-1/2" (546mm) A 15" (381mm) B 13-1/2" (343mm) C 20-7/8" (530mm) N/A 988 lb.
SPECIFICATIONS: L W J H C SIDE VIEW A END VIEW B DRAIN / OVERFLOW GENERAL SPECIFICATIONS FOR STUDIO CORNER WHIRLPOOLS AND BATH TUBS Description Deck Trim 2945 Studio N/A Dimensions L-W-H Drain / Overflow A 15-3/4" (400mm) B 10-1/4" (260mm) L 60" (1524mm) W 32" (813mm) H 22" (559mm) Height to Underside of Deck: C Cut Out Pier GxF C 22-1/2" (572mm) N/A Rough-In Recess ExD Tub Edge to Centerline Overflow: J 60-3/16" (1528mm) x 30-1/2" (774mm) Weight with Water / Floor Loading Product W
SPECIFICATIONS: L W H SIDE VIEW J C A END VIEW B DRAIN / OVERFLOW GENERAL SPECIFICATIONS FOR GREEN TEA WHIRLPOOLS AND BATH TUBS Description Dimensions L-W-H Drain / Overflow 3571 Green Tea 5' x 36" L 60" (1524mm) W 36" (914mm) H 21" (533mm) A 16" (406mm) B 11-1/2" (349mm) 3572 Green Tea 5-1/2' x 36" L 66" (1676mm) W 36" (914mm) H 21" (533mm) 3573 Green Tea 6' x 36" Height to Underside of Deck: C Cut Out Pier GxF Rough-In Recess ExD Tub Edge to Centerline Overflow: J Weight with Water /
ROUGH-IN REFERENCES MODEL SERIES 3571 60" (1524mm) 14-3/4" (375mm) 11-1/2" (292mm) 36" (914mm) 9" (229mm) C L CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 58.5" x 34.5" (1486 x 876mm) MODEL SERIES 3572 66" (1676mm) 14-3/4" (375mm) 11-1/2" (292mm) 36" (914mm) 9" (229mm) C L CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 64.5" x 34.5" (1638 x 876mm) 21 754532-100 Rev.
ROUGH-IN REFERENCES MODEL SERIES 3573 72" (1829mm) 14-3/4" (375mm) 11-1/2" (292mm) 36" (914mm) 9" (229mm) CL CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 70.5" x 34.5" (1780 x 876mm) MODEL SERIES 3574 60" (1524mm) 14-3/4" (375mm) 11-1/2" (292mm) 42" (1067mm) 9" (229mm) CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 58.5" x 40.5" (1486 x 1029mm) 754532-100 Rev.
ROUGH-IN REFERENCES MODEL SERIES 3575 72" (1829mm) 14-3/4" (375mm) 11-1/2" (292mm) 42" (1067mm) 9" (229mm) CL CUTOUT IN FLOOR FOR DRAIN PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS OUTLINE OF CUTOUT 70.5" x 40.5" (1780 x 1029mm) 23 754532-100 Rev.
SPECIFICATIONS: L W J H SIDE VIEW C A END VIEW DRAIN / OVERFLOW B GENERAL SPECIFICATIONS FOR SERIN WHIRLPOOLS AND BATH TUBS Description Dimensions L-W-H Drain / Overflow Height to Underside of Deck: C Cut Out Pier GxF Rough-In Recess ExD 3581 Serin 5' x 32" L 60" (1524mm) W 32" (813mm) H 23" (584mm) A 16-3/4" (425mm) B 10-1/4" (260mm) C 20" (508mm) 58-1/2" (1486mm) x 30-1/2" (775mm) 3582 Serin 5-1/2' x 36" L 66" (1676mm) W 36" (914mm) H 23" (584mm) A 16-7/8" (429mm) B 9-3/4" (248mm)
ROUGH-IN REFERENCES MODEL SERIES 3582 66" (1676mm) 33" (838mm) 9" x 12" (227 x 305mm) FLOOR CUTOUT C/L DRAIN 9-3/4" (248mm) 4-1/8" (105mm) OUTLINE OF CUTOUT 36" (914mm) INTEGRAL FAUCET DECK PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS 4" (102mm) MODEL SERIES 3583 68" (1727mm) 34" (864mm) C/L DRAIN 9"x12" (227x305mm) FLOOR CUTOUT 11-1/2" (292mm) 4-7/8" (124mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS INTEGRAL FAUCET DECK 4-3/4" (121mm) OUTLINE OF CUTOUT OUTLINE OF SKID RESIS
ROUGH-IN REFERENCES MODEL SERIES 3584 72" (1829mm) 36" (914mm) C/L DRAIN 9" x 12" (227 x 305mm) FLOOR CUTOUT 10-1/4" (260mm) 4-7/8" (124mm) 42" (1067mm) PROVIDE ACCESS TO PUMP SERVING ON ALL INSTALLATIONS INTEGRAL FAUCET DECK 754532-100 Rev.
ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes. ! WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter. 2. Grounding is required. The unit should be installed by a licensed electrician and grounded. 3.
ELECTRICAL INSTALLATION INSTRUCTIONS (continued) ELECTRICAL FEED 120V, 60HZ 15A GFCI GFCI ELECTRONIC ACTIVATED AIR BATH (4 BUTTON PANEL) ELECTRICAL FEED 120V, 60HZ 15A GFCI GFCI ELECTRONIC ACTIVATED AIR BATH WITH LIGHTS (5 BUTTON PANEL) 754532-100 Rev.
ELECTRICAL INSTALLATION INSTRUCTIONS (continued) ECOSILENT PUMP HAS P3JJ PLUG ELECTRICAL FEED 120V, 60HZ 15A GFCI GFCI ELECTRONIC ACTIVATED ECOSILENT WHIRLPOOL (1 BUTTON PANEL) ECOSILENT PUMP HAS P3JJ PLUG ELECTRICAL FEED 120V, 60HZ 15A GFCI GFCI ELECTRONIC ACTIVATED ECOSILENT WHIRLPOOL WITH LIGHTS (3 BUTTON PANEL) 29 754532-100 Rev.
ELECTRICAL INSTALLATION INSTRUCTIONS (continued) USE THREE GFCI OUTLETS (USA MARKET) ELECTRICAL FEED 120V, 60HZ 15A GFCI (FOR HEATER) WHIRLPOOL HEATER IS FACTORY INSTALLED ON COMBINATION TUBS GFCI ECOSILENT PUMP HAS P3JJ PLUG ELECTRICAL FEED 120V, 60HZ 15A GFCI GFCI ELECTRICAL FEED 120V, 60HZ 15A GFCI GFCI ELECTRONIC ACTIVATED COMBINATION TUB WITH LIGHTS (4 BUTTON PANEL) 754532-100 Rev.
ELECTRICAL INSTALLATION INSTRUCTIONS (continued) USE THREE JUNCTION BOXES (CANADA MARKET) ELECTRICAL FEED 120V, 60HZ 15A GFCI (FOR HEATER) GFCI White Black Green/Copper ELECTRICAL FEED 120V, 60HZ 15A GFCI GFCI ECOSILENT PUMP HAS P3JJ PLUG White Black Green/Copper ELECTRICAL FEED WHIRLPOOL HEATER IS FACTORY INSTALLED ON COMBINATION TUBS TO BOX 120V, 60HZ 15A GFCI GFCI TO BOX White Black Green/Copper ELECTRONIC ACTIVATED COMBINATION TUB WITH LIGHTS (4 BUTTON PANEL) 31 754532-100 Rev.
ELECTRICAL INSTALLATION INSTRUCTIONS (continued) (HEATER) Ensure the heater and pump are properly GROUNDED and BONDED as required. Attach the 8 AWG solid copper conductor supplied with the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3. HEATER ON E-Z INSTALL™ The conductor is secured to the lugs using set screws.
REMOTE BLOWER LOCATION OPTION IMPORTANT! It is not necessary that the blower motor be relocated. This option is provided for the case that a particular installation makes this effort practical. NOTE: Relocating blower motor from factory installed location, see photo 1, will require disassembly of air blower from mounting board. Keep all hardware for reattachment at new location. Additional hardware will be required depending upon final desired position of air blower. Follow all instructions listed below.
REMOTE BLOWER LOCATION OPTION (continued) FOR THE COMBINATION WHIRLPOOL / AIR BATH CONFIGURATIONS ONLY: Up to two additional control box extensions (P/N 754512-0070A) are required as shown in photo 4 (below). Simply extend the cables going to the blower by adding in the extension cables. Be careful not to damage the cable connections and never plug in cables while power is applied to blower and/or pump. PUMP LONGER CONTROL PANEL CABLE (754025-0073A) CONTROL PANEL 4. LIGHTS 754532-100 Rev.
Operation: Single Speed Whirlpool AIR SWITCH ELECTRONIC SWITCH BATHING: • Fill bath with water at a comfortable bathing temperature - If your whirlpool is equipped with the optional EZ-Heater, it will automatically maintain the water temperature. • IMPORTANT: Do NOT fill the whirlpool more than 2/3 full before getting in, as it may overflow. • IMPORTANT: Do NOT add bath oils or salts – this will damage the whirlpool pump.
Operation: EcoSilent Whirlpool with Lights DISPLAY COLORS 1ST WHITE 2ND SLOW RAINBOW CYCLE 3TH FAST RAINBOW CYCLE 4TH TURQUOISE 5 BLUE TH 3-BUTTON ELECTRONIC SWITCH 6TH MAGENTA 7TH RED 8TH ORANGE 9TH YELLOW 10 GREEN TH 11 TH RETURN TO SLOW RAINBOW CYCLE BATHING: • Fill bath with water at a comfortable bathing temperature - If your whirlpool is equipped with the optional EZ-Heater, it will automatically maintain the water temperature.
Operation: Air Bath BATHING: • Close drain by rotating Drain Overflow Knob COUNTER-CLOCKWISE • Fill bath with water at a comfortable bathing temperature, adding bath oils or salts as desired. OPERATING AIR MASSAGE SYSTEM: ON/OFF: Press this button once to turn air-blower on. Press again to turn air-blower off. AIR SPEED INCREASE: Pressing this button will increase to the next higher speed. AIR SPEED DECREASE: Pressing this button will decrease to the next lower speed.
Operation: Air Bath with Lights BATHING: • Close drain by rotating Drain Overflow Knob COUNTER-CLOCKWISE • Fill bath with water at a comfortable bathing temperature, adding bath oils or salts as desired. OPERATING AIR MASSAGE and CHROMATHERAPY SYSTEM: ON/OFF: Press this button once to turn air-blower on. Press again to turn air-blower off. AIR SPEED INCREASE: Pressing this button will increase to the next higher speed. AIR SPEED DECREASE: Pressing this button will decrease to the next lower speed.
Operation: Air Bath with Lights (continued) EXITING THE BATH • Be sure to turn off the air blower before draining bath. • Open drain by rotating drain knob clockwise. DRYING CYCLE OPTIONS STANDARD DRYING CYCLE An automatic drying cycle will start 20 minutes after the blower is turned off. The blower LED blinks while waiting for the purge cycle. 24H PROGRAMMABLE DRYING CYCLE The system must be stopped prior to activation or deactivation. Activation: Determine at which time you wish to purge to activate.
Operation: Combination Tub with Lights BATHING: • Close drain by rotating Drain Overflow Knob COUNTER-CLOCKWISE • Fill bath with water at a comfortable bathing temperature, adding bath oils or salts as desired. OPERATING AIR MASSAGE and CHROMATHERAPY SYSTEM: • Press this button to turn blower on. • Press this button again to turn blower off. • Press and hold button to increase blower speed. Release button at desired speed. • Press and hold button to decrease speed. Release button at desired speed.
Operation: Combination Tub with Lights (continued) EXITING THE BATH • Be sure to turn off the air blower before draining bath. • Open drain by rotating drain knob clockwise. DRYING CYCLE OPTIONS STANDARD DRYING CYCLE An automatic drying cycle will start 20 minutes after the blower is turned off. The blower LED blinks while waiting for the purge cycle. 24H PROGRAMMABLE DRYING CYCLE The system must be stopped prior to activation or deactivation.
Your American Standard whirlpool is designed to give you many years of pleasure with reasonable care and maintenance. Your new acrylic bathtub is tough, durable and easy to care for. The colors have been formulated to match other American Standard fixtures and enhance your choice of bathroom decorations. The high gloss surface will retain its lasting luster with proper care and maintenance. CLEANING AND MAINTENANCE: • Always fill the tub with temperate water.
AS America, Inc. Limited Lifetime Warranty for Premium Acrylic Air Baths AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this whirlpool or any of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser.
754532-100 Rev.
