Owner`s manual

16-EN
Sound Setting
You can flexibly customize the unit to suit your own preference and
usage. From the AUDIO SETUP menu, Audio Setting can be modified.
1 Press and hold AUDIOSETUP for at least 2 seconds to
activate the SETUP mode.
2 Turn the Rotary encoder to select AUDIO, and then press
ENTER.
AUDIO
*1
 GENERAL  DISPLAY  TUNER  IPOD&USB  APP
 BLUETOOTH  AUDIO
*1 Adjustment cannot be performed during phone call.
3 Turn the Rotary encoder to select the desired sound
setting menu, and then press ENTER.
FAC TORY EQ
*2/*3
 9BAND P-EQ
*2/*4
 VOL LV ADJ 
SUBWOOFER  SUBW PHASE
*5
 SUBW SYS
*5
 POWER IC 
MX SETTING
*2
 LENGTH
*2
 TCR
*2
 SPATIAL
*2
 X-OVER
*2

FAC TORY EQ
*2 Adjustment cannot be performed when DEFEAT is set to ON.
*3 Any changes made to either FACTORY EQ or 9BAND P-EQ are
reflected in the others’ settings.
*4 In step 3, after selecting a Band (BAND1 to BAND9) from
9BAND P-EQ adjustment mode, turn the Rotary encoder to
select the desired item, and then press ENTER to continue to
step 4.
*5 These functions are inoperable when Subwoofer is set to OFF.
4 Turn the Rotary encoder to change the setting, and then
press ENTER.
(e.g. Select SUBWOOFER ON or SUBWOOFER OFF)
5 Press and hold AUDIOSETUP for at least 2 seconds to
return to normal mode.
Notes
• Pressing t returns to the previous Sound menu mode.
• If no operation is performed for 60 seconds, Sound menu mode is
cancelled.
10 typical equalizer settings are preset at the factory for a variety of
musical source material. USER settings are created in the 9BAND P-EQ
mode.
USER  FLAT (Initial setting) POPS  ROCK  NEWS  JAZZ
 ELEC DANCE  HIP HOP  EASY LIS  COUNTRY 
CLASSICAL
Note
• The 9-Band, Parametric EQ is used to create the Factory EQ settings.
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
1 After selecting a BAND (BAND1 ~ BAND9) from the 9BAND
P-EQ adjustment mode, turn the Rotary encoder to select
the desired setting item, and then press ENTER.
CENTER FRQ  WIDTH (Q)  LEVEL  CENTER FRQ
2 Turn the Rotary encoder to select the desired setting
value, and then press ENTER.
3 Press t to return to the previous step.
Adjusting the Frequency (CENTER FRQ)
Adjustable frequency bands: 20 Hz to 20 kHz
Setting the Bandwidth (WIDTH (Q))
Setting contents:
3.0 (Initial setting) / 4.0 / 5.0
Adjusting the Level
Setting contents:
−7 to +7 (Initial setting: 0)
Notes
• BAND2 and BAND8 are the same as the Bass and Treble controls.
Their Level adjustment can also be controlled by pressing AUDIO and
selecting Bass Level or Treble Level. Refer to “Adjusting Subwoofer
Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat” on page 15.
• Settings exceeding the frequency of adjacent bands are not available.
• While adjusting the 9BAND P-EQ, you should consider the frequency
response of the connected speakers.
• The 9-Band, Parametric EQ is used to create the Factory EQ settings.
The output level of each source is individually adjustable. For example, if
the TUNER level sounds lower than CD, its output can be adjusted
without affecting the other sources.
 Setting item: VOL LV ADJ
 Further setting items: TUNER / DISC / USB / IPOD / BT AUDIO
/ PANDORA / AUX
Setting contents:
−14 dB ~ +14 dB
Use steps 1 to 5 to select the category you wish to modify. For
details on how to change each setting, see the following
sections below.
Equalizer Presets (FACTORY EQ)
Adjusting the Parametric Equalizer Curve
(9BAND P-EQ)
Band1 20 Hz ~ 100 Hz (63 Hz)
Band2 63 Hz ~ 315 Hz (125 Hz)
Band3 125 Hz ~ 500Hz (250 Hz)
Band4 250 Hz ~ 1 kHz (500 Hz)
Band5 500 Hz ~ 2 kHz (1 kHz)
Band6 1 kHz ~ 4 kHz (2 kHz)
Band7 2 kHz ~ 7.2 kHz (4 kHz)
Band8 5.8 kHz ~ 12 kHz (8 kHz)
Band9 9 kHz ~ 20 kHz (16 kHz)
Setting the Source Volume Level