Blower Operating Manual

ManualsBrandsAir King ManualsBlowerB600

www.airkinglimited.com

111597005 New 3-07

1 of 8

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT

YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions

should always be followed to reduce the risk of fire,

electric shock and injury to person, including the following:

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND

INJURY TO PERSON, OBSERVE THE FOLLOWING:

1. Read all instructions before installing or using range hood.

2. Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

3. Before servicing or cleaning the unit, switch power off at service panel

and lock the service disconnecting means to prevent power from being

switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to

the service panel.

4. Installation work and electrical wiring must be done by qualified person(s)

in accordance with all applicable codes and standards, including fire-

related construction.

Model B600 Blower

SAVE THESE INSTRUCTIONS

5. Sufficient air is needed for proper combustion and exhausting of gases

through the flue (chimney) of fuel burning equipment to prevent back

drafting. Follow the heating equipment manufacturer’s guideline and safety

standards such as those published by the National Fire Protection

Association (NFPA) and the American Society for Heating, Refrigeration,

and Air Conditioning Engineers (ASHRAE), and the local code authorities.

CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO

EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.

6. To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

7. Refer to the instructions included with the Range Hood Canopy for additional

safety information.

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

INSTALLATION INSTRUCTIONS

CAUTION:

MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL

BEFORE STARTING INSTALLATION.

WARNING: THIS BLOWER IS INTENDED FOR USE ONLY IN AIR KING

PROFESSIONAL SERIES RANGEHOOD CANOPIES MARKED SUITABLE FOR USE

WITH THIS BLOWER. DO NOT TO INSTALL IN ANY OTHER APPLICATION.

SECTION 1

Preparing for installation

NOTE: Before installing blower, make sure range hood canopy is properly

installed and securely in place. See “Range Hood Mounting Instructions”.

1. Unpack blower from the carton and confirm that all pieces are present. In

addition to the blower you should have:

8 - 8-32 Screws

8 - Washers

1 - Fuse

1 - Instruction/Safety Sheet

2. The installation of the blower is slightly different from one canopy height

to another. For 18" high canopies proceed to Section 2, for 10" high canopies

proceed to Section 3.

SECTION 2

Installation into 18" High Canopy

1. Lift blower up into the hood canopy and slide the keyhole slots in the motor

mounting flange over the two studs of the hood. Slide the motor into place

and tighten the hex nuts on the mounting stud while lining up the 8 holes

in the motor mounting flange to the 8 screw studs of the hood (Figure 1).

Figure 1

Keyholes

Stud w/Hex Nuts

Screw Stud

Summary of content (8 pages)

PAGE 1
IMPORTANT INSTRUCTIONS OPERATING MANUAL Model B600 Blower READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
PAGE 2
. Using the included 8-32 screws and washers, mount the blower in place and tighten all screws. Confirm that the blower is securely seated in place and there are no air gaps around the blower gasket. 4. Plug both the 3 wire and 4 wire quick connect cords from the blower into the appropriate receptacles located on the inside front of the hood canopy. These cords will only fit into the receptacles one way (Figure 2). 3.
PAGE 3
111597005 New 3-07 www.airkinglimited.
PAGE 4
INSTRUCTIONS IMPORTANTES – MANUEL D’OPÉRATION Modèle B600 La Soufflante LIRE ET CONSERVER CES INSTRUCTIONS LIRE SOIGNEUSEMENT AVANT DE TENTER D’ASSEMBLER, INSTALLER, OPÉRER OU DE RÉPARER LE PRODUIT DÉCRIT. PROTÉGEZ VOUS-MÊME ET LES AUTRES EN OBSERVANT TOUTE L’INFORMATION DE SÉCURITÉ. FAILLIR À SE CONFORMER AUX INSTRUCTIONS PEUT RÉSULTER EN BLESSURE PERSONNELLE GRAVE ET/OU EN DOMMAGE À LA PROPRIÉTÉ. CONSERVER CES INSTRUCTIONS POUR RÉFÉRENCES FUTURES.
PAGE 5
2. 3. En utilisant les vis 8-32 et les rondelles comprises, monter la soufflante en place et serrer toutes les vis. Confirmer que la soufflante est solidement assise en place et qu’il n’y a pas de fuite d’air autour du joint d’étanchéité de la soufflante. Brancher les cordons à connecteurs rapides à 3 fils et 4 fils de la soufflante dans les réceptacles appropriés situés sur l’intérieur de l’avant du couvert de la hotte. Ces cordons ne s’ajusteront que d’une seule manière dans les réceptacles (Figure 2).
PAGE 6
111597005 New 3-07 www.airkinglimited.
PAGE 7
INSTRUCCIONES IMPORTANTES – MANUAL DE OPERACIÓN Modelo B600 El Soplador LEA Y GUARDE ESTAS INSTRUCCIONES LEA CUIDADOSAMENTE ANTES DE INTENTAR MONTAR, INSTALAR, OPERAR O MANTENER EL PRODUCTO DESCRITO. PROTÉJASE A USTED MISMO Y A LOS DEMÁS OBEDECIENDO TODA LA INFORMACIÓN DE SEGURIDAD. ¡EL HECHO DE NO CUMPLIR CON LAS INSTRUCCIONES PODRÍA RESULTAR EN DAÑOS PERSONALES Y/O A LA PROPIEDAD! CONSERVE LAS INSTRUCCIONES PARA REFERENCIA FUTURA.
PAGE 8
2. Usando los tornillos y las arandelas Nº 8-32 incluidos, monte el soplador en su lugar y ajuste todos los tornillos. Confirme que el soplador esté firmemente apoyado en su lugar y que no haya brechas de aire alrededor de la junta del soplador. 4. Conecte los cables de conexión rápida de 3 alambres y de 4 alambres del soplador en los receptáculos apropiados ubicados en la parte frontal interior de la bóveda de la campana. Estos cables sólo encajarán en los receptáculos en un solo sentido (Figura 2). 3.