OWNERS MANUAL SH IE LD UP - 8 TO 18 SH IE LD FT . SP DO W N RE AD W ID TH - 3 TO 4 FT . SP RE AD W ID TH Model No. 45-02101-101 PRO 125# BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts PRINTED IN U.S.A. FORM NO. 47438 (Rev.
TABLE OF CONTENTS SAFETY RULES...............................................................2 CARTON CONTENTS......................................................2 ASSEMBLY ......................................................................4 OPERATION ....................................................................8 MAINTENANCE & STORAGE............................................9 LUBRICATION..................................................................9 PARTS EXPLOSION.......................
FULL SIZE HARDWARE REFERENCE CHART J A C B D E K M L I H F G NOT SHOWN FULL SIZE N O P Q R S T U V REF. QTY. A B C D E F G H I J K 3 2 6 2 6 16 17 5 4 1 1 DESCRIPTION Bolt, Carriage 1/4" x 3/4" Bolt, Hex 1/4" x 5/8" Bolt, Hex 1/4" x 3/4" Bolt, Hex 1/4" x 1-1/2" Bolt, Hex 1/4" x 1-3/4" Nut, Hex Lock 1/4-20 Washer, 5/16" Washer, Nylon Washer, 3/4" Cotter Pin, 3/32" x 3/4" Cotter Pin, 1/8" x 1-1/2" 3 REF. QTY.
5. Place the short spacer tube and a 3/4" washer onto the end of the axle that has the large drilled hole (left hand side). See figure 2. ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY (1) (2) (2) 6. Place the drive wheel onto the axle. The notched hub and the air valve should face to the outside. See figure 2. Pliers 7/16" Open End or Box Wrenches 9/16" Open End or Box Wrenches 7. Fasten the wheel to the axle using a 1/4" x 1-3/4" hex bolt and a 1/4" hex lock nut. See figure 2.
14. Assemble the leg stand tube to the handle tube (long) using two 1/4" x 1-1/2" hex bolts and two 1/4" hex lock nuts. Tighten. See figure 5. 10. Assemble the (long) handle tube to the side of the crossover tube opposite the shaft support plate, as shown in figure 4. Fasten the handle tube to the middle hole using the bolt, flat washer and hex lock nut which you removed in step 9. Do not tighten yet. 15. Place the vinyl cap on the leg stand tube. See figure 5.
21. Hook the free end of the flow control rod through the hole in the slide gate bracket located near the bottom of the hopper. See figure 9. 18. Assemble the flow control arm to the flow control mounting bracket using one 1/4" x 5/8" hex bolt and one 1/4" hex lock nut. Do not over tighten. The flow control arm must pivot freely. See figure 7. 19. Hook one end of the spring through the hole at the bend in the flow control rod. Hook the other end in the hole in the flow control mounting bracket.
24. Assemble the flow control gauge onto the flow control mounting bracket using a 1/4" x 3/4" carriage bolt, a nylon washer and the hand knob. See figure 11. 28. Assemble the spreader shield to the front swivel brackets using two 1/4" x 3/4" carriage bolts, 5/16" washers and the two 1/4" plastic knobs. See figure 13. 25. Push the flow control arm forward to the off position and slide flow control mounting bracket toward hopper until closure plate (bottom of hopper) is fully closed.
USING THE SPREADER OPERATION 1. Determine approximate square footage of area to be covered and estimate amount of fertilizer or seed required. 2. With flow control arm in off position, set flow rate gauge at number indicated in flow rate chart for light or heavy application rate. Also refer to instructions on bag for manufacturers recommended settings. 3. With the flow control arm set at the off position, fill the hopper with up to 125 pounds of material, breaking up lumpy fertilizer as you fill hopper.
IMPORTANT: Application rates (shown on chart) are affected by humidity and mixture content of material (granular and pellet). Minor adjustment of the flow rate setting may be necessary to compensate for these variables. The rate chart is calculated for light and heavy application. The faster you walk, the wider the broadcast width. A variation in speed will determine the flow rates and width of broadcast. LUBRICATION 1. 2. 3. 4. Apply a little automotive grease to the sprocket and gear.
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02101-101 68 39 61 64 E 67 64 F 65 63 9 64 48 59 64 61 44 52 39 55 14 41 17 55 70 42 64 38 9 8 37 1 37 71 40 29 72 31 5 9 39 30 53 2 60 4 33 9 D 9 62 10 D 13 37 A 35 32 56 C 37 19 22 20 12 49 58 36 11 69 64 47 9 57 46 53 37 B 64 9 6 E F 9 63 64 A 34 27 66 37 54 61 3 25 37 9 40 38 7 26 64 45 9 9 19 18 21 9 21 43 4 C 51 50 51 B 28 23 51 35 23 16 9 9 10 24 15
REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02101-101 REF. NO. PART NO. QTY. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 44466 43882 62482 44462 23753 23758 43648 23756 43013 43808 43084 43086 43064 44463 44456 44457 44464 23752 43851 43871 1540-032 1540-162 44798 44494 47437 04367 43850 44500 C-9M5732 23766 43878 43070 44468 44514 23525 23762 1 4 1 1 1 1 2 1 24 1 2 2 2 1 1 1 1 1 2 1 5 1 2 1 1 1 1 1 2 1 1 5 1 1 2 1 DESCRIPTION REF. NO.
REPAIR PARTS 303 West Raymond Sullivan, IL. 61951 (217) 728-8388 / www.agri-fab.