LB3680WT USER MANUAL FR Notice d'utilisation Lavante-séchante
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................3 2. CONSIGNES DE SÉCURITÉ........................................................................................6 3. INSTALLATION............................................................................................................7 4. DESCRIPTION DE L'APPAREIL.................................................................................12 5.
FRANÇAIS 3 Sous réserve de modifications. 1. INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com 1.2 Sécurité générale • • • • • • • • • • • • Ne modifiez pas les caractéristiques de cet appareil. L'appareil peut être installé de façon autonome ou sous un plan de travail si l'espace disponible le permet. L'appareil ne doit pas être installé derrière une porte à serrure, une porte coulissante ni une porte battante dotée d'une charnière du côté opposé à l'appareil qui pourrait empêcher l'ouverture complète de la porte.
FRANÇAIS • • • • • • • • • • 5 Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger lié à l'électricité. Retirez les peluches ou morceaux d'emballage accumulés autour de l'appareil.
www.aeg.com • • • température plus basse qui lui évitera de subir des dommages. Ne pulvérisez pas d'eau ni de vapeur à haute pression pour nettoyer l'appareil. Nettoyez l'appareil avec un chiffon humide. Utilisez uniquement des produits de lavage neutres. N'utilisez pas de produits abrasifs, de tampons à récurer, de solvants ni d'objets métalliques. Avant toute opération d'entretien, éteignez l'appareil et débranchez la fiche de la prise secteur. 2. CONSIGNES DE SÉCURITÉ 2.
FRANÇAIS jusqu'à ce qu'elle soit parfaitement propre et claire. • Pendant et après la première utilisation de l'appareil, vérifiez qu'aucune fuite n'est visible. 2.4 Utilisation AVERTISSEMENT! Risque de blessure, de choc électrique, d'incendie, de brûlures ou de dommage matériel à l'appareil. • Cet appareil est exclusivement destiné à une utilisation domestique.
www.aeg.com Assurez-vous de ne pas endommager les tuyaux. 2. Retirez la partie supérieure en carton et tous les matériaux d'emballage en polystyrène. 7. Retirez la protection en polystyrène en bas de l'appareil. 1 3. Retirez le film interne. 2 8. Remettez l'appareil en position verticale. 4. Ouvrez le hublot et retirez la cale en polystyrène du joint du hublot, ainsi que tous les articles présents dans le tambour. 9.
FRANÇAIS 9 Assurez-vous que la circulation de l'air sous l'appareil ne soit pas entravée par des tapis. Veillez à ce que l'appareil ne touche pas le mur ni d'autres éléments. 2. Desserrez ou serrez les pieds jusqu'à ce que l'appareil soit de niveau. 10. Dévissez les trois boulons à l'aide de la clé fournie avec l'appareil. AVERTISSEMENT! Ne placez ni carton, ni bois, ni autre matériau sous les pieds de l'appareil pour le mettre de niveau. 11. Retirez les entretoises en plastique. 12.
www.aeg.com ATTENTION! Assurez-vous que les raccords ne fuient pas. N'utilisez pas de rallonge si le tuyau d'alimentation est trop court. Contactez le service après-vente pour remplacer le tuyau d'alimentation. 3.3 Tuyau d'arrivée d'eau 1. Raccordez le tuyau d'arrivée d'eau à l'arrière de l'appareil. 2. Placez-le vers la droite ou la gauche, en fonction de la position de votre robinet d'eau. 3.
FRANÇAIS 2. Sur le bord d'un évier : attachez le guide au robinet d'eau ou au mur. Veillez à ce que le guide de tuyau en plastique ne puisse pas se déplacer lors de la vidange de l'appareil. Vérifiez que l'extrémité du tuyau de vidange n'est pas plongée dans l'eau. Il pourrait y avoir un reflux d'eau sale dans l'appareil. 3. À une conduite fixe dotée d'une ventilation spéciale : insérez directement le tuyau dans la conduite d'évacuation. Reportezvous à l'illustration.
www.aeg.com 4. DESCRIPTION DE L'APPAREIL 4.
FRANÇAIS 13 5. BANDEAU DE COMMANDE 5.1 Description du bandeau de commande 3 2 1 Programme Baumwolle Baumwolle Eco Pflegeleicht Feinwäsche Wolle/ Handwäsche Outdoor NonStop 60min 4 5 Dampf Spülen Schleudern/ Abpumpen Mode 11 10 9 12 1 Sélecteur de programme 2 Écran d'affichage 3 Touche de la durée de séchage 4 Touche du degré de séchage 5 Touche tactile Mode • Lavez • Sec 6 Touche Départ/Pause 7 7 Option Taches 5.
www.aeg.com Voyant de charge maximale. Le voyant de la charge de linge. clignote durant l'estimation Voyant de charge maximale. Il clignote lorsque la charge de linge dépasse la charge maximale prévue pour le programme sélectionné. Si vous lancez un programme alors que le tambour est surchargé, clignote également à la fin du programme. Indicateur du temps de séchage. Indicateur Hublot verrouillé. L'indicateur numérique peut afficher : • La durée du programme ( chage). • Le départ différé (par ex.
FRANÇAIS 15 5.3 Plaques multilingues Des plaques adhésives en différentes langues sont fournies avec l'appareil. Collez la plaque souhaitée autour du sélecteur de programme. Program Koge-/Kulørt Syntetisk Finvask Uld/Silke Damp Antiallergi 20 min. - 3 kg Motionstøj Vattæpper Jeans 6. MANETTES ET TOUCHES 6.1 Introduction En appuyant sur une combinaison de touches, ne pas incliner vos doigts vers le bas. Les capteurs des touches situées en-dessous sont sensibles et peuvent interférer avec votre choix. 6.
www.aeg.com • Diminuer la vitesse d'essorage. Seules les vitesses disponibles pour le programme sélectionné s'affichent. • Activer l’option Sans essorage . Elle est disponible uniquement avec le programme Essorage/Vidange. L’appareil sautera toutes les phases d’essorage et vidange uniquement l'eau. L'indicateur s'allume. 6.6 Taches/Prélavage Appuyez à plusieurs reprises sur la touche pour activer une des deux options. L'indicateur correspondant s'affiche.
FRANÇAIS 6.10 Degré de séchage 6.11 Mode Appuyez sur cette touche pour sélectionner l'un des 3 degrés de séchage proposés par l'appareil. Grâce à cette touche, un cycle peut effectuer : L'indicateur correspondant au degré de séchage s'affiche : • • • repasser. ranger. Prêt à repasser : linge à Prêt à ranger : linge à Très sec : linge à sécher entièrement. Certains degrés automatiques de séchage ne peuvent pas être sélectionnés selon le type de textile.
www.aeg.com Programme Description du programme N'utilisez pas d'adoucissant et assurez-vous que le distributeur de produit de lavage ne contient pas de résidus d'adoucissant. Outdoor Vêtements d'extérieur, de travail, de sport, imperméables et tissus perméables à l'air, vestes à molleton ou doublure isolante amovibles. En effectuant un programme de lavage et séchage non-stop, la phase de séchage agit également comme un restaurateur d'imperméabilité.
FRANÇAIS 19 Programme Description du programme Essorage/Vidange Pour essorer le linge et vidanger l'eau du tambour. Tous textiles, excepté la laine et les tissus délicats. 1) Durant ce cycle, le tambour tourne lentement pour garantir un lavage en douceur. Le tambour peut donner l'impression de ne pas tourner, ou de ne pas tourner correctement, mais son fonctionnement est normal pour ce programme. 2) Si vous sélectionnez un programme Vapeur avec du linge sec, il sera humide à la fin du cycle.
www.aeg.com Programme Température par défaut Plage de températures Vitesse d'essorage maximale Plage de vitesses d'essorage Charge maximale 1600 tr/min Essorage/Vidange 8 kg 1600 tr/min ■ Essorage/Vidange ■ Rinçage ■ Vapeur ■ Propre&Sec 60Min.
Degré de séchage 21 Essorage/Vidange Rinçage Vapeur Propre&Sec 60Min. Outdoor Laine/Lavage à la main ■4) Délicats ■ Synthétiques Coton Eco Options Blanc/Couleurs Programme FRANÇAIS 1) Si vous sélectionnez l'option Sans essorage, l'appareil vidange uniquement l'eau. 2) Cette option n'est pas disponible avec des températures de lavage inférieures à 40 °C. 3) Si vous sélectionnez la durée la plus courte, nous vous recommandons de réduire la charge de linge.
www.aeg.com Degré de séchage Prêt à Ranger (Cupboard Dry)1) Pour les articles à ranger directement Type de textile Charge Coton et lin (peignoirs, serviettes de bain, etc.
FRANÇAIS Degré de sécha- Type de textile ge Charge (kg) Prêt à Ranger Coton et lin (Cupboard Dry) (peignoirs, serviettes de bain, etc.
www.aeg.com 8.3 Signaux sonores Les signaux sonores retentissent lorsque le programme est terminé (suite de signaux pendant environ 2 minutes). Pour désactiver/activer les signaux sonores, appuyez simultanément sur les touches 6 secondes. et pendant Si vous désactivez les signaux sonores, ils continueront à retentir si l'appareil présente une anomalie. 8.4 Rinçage plus permanent lorsque vous sélectionnez un nouveau programme.
FRANÇAIS 2. Dépliez-les le plus possible avant de les placer dans l'appareil. 3. Mettez le linge dans le tambour, un article à la fois. Assurez-vous de ne pas surcharger le tambour. 4. Fermez bien le hublot. 25 Volet pour produit de lavage en poudre ou liquide. Suivez toujours les instructions imprimées sur l'emballage des produits de lavage, mais nous vous recommandons de ne pas dépasser le niveau maximal indiqué ( ). Cette quantité vous garantira les meilleurs résultats de lavage.
www.aeg.com A 4. Pour utiliser de la lessive liquide, tournez le volet vers le bas. B Avec le volet en position BASSE : • N'utilisez pas de lessives liquides gélatineuses ou épaisses. • Ne versez pas de lessive liquide audelà du niveau maximal indiqué sur le volet. • Ne sélectionnez pas de phase de prélavage. • Ne sélectionnez pas la fonction Départ différé. 5. Dosez le produit de lavage et l'assouplissant. 6. Fermez soigneusement le distributeur de produit de lavage.
FRANÇAIS Le voyant correspondant cesse de clignoter et reste fixe. Sur l'affichage, le voyant de la phase en cours commence à clignoter et le voyant de la charge maximale s'éteint. Le programme démarre et le hublot est verrouillé. L'indicateur s'allume. La pompe de vidange peut momentanément se mettre en route lorsque l'appareil se remplit d'eau. 10.7 Départ d'un programme avec départ différé 1.
www.aeg.com la surcharge. Dans ce cas, les résultats de lavage ne seront pas optimaux. Environ 20 minutes après le départ du programme, la durée du programme peut de nouveau être ajustée en fonction de la capacité d'absorption de l'eau par les tissus. La détection ProSense est uniquement effectuée pour les programmes de lavage complets (sans aucune phase supprimée). 10.
FRANÇAIS sélectionnez le programme Essorage/Vidange puis appuyez sur la touche Départ/Pause (Start/Pause). 10.13 Fin du programme Lorsque le programme est terminé, l'appareil s'éteint automatiquement. Les signaux sonores retentissent (s'ils sont activés). Sur l'affichage, tous les voyants de la phase de lavage sont fixes et l'affichage du temps indique . Le voyant de la touche Départ/Pause (Start/Pause) s'éteint. Le hublot se déverrouille et le voyant s'éteint.
www.aeg.com 1. Appuyez sur la touche Marche/Arrêt pendant quelques secondes pour allumer l'appareil. 2. Chargez le linge dans le tambour, un article à la fois. 3. Versez le produit de lavage et les additifs dans le compartiment approprié. 4. Tournez le sélecteur sur le programme de lavage. La température et la vitesse d'essorage par défaut s'affichent. Si nécessaire, modifiez-les en fonction de votre linge. La charge maximale recommandée pour la phase de lavage s'affiche également. 5.
FRANÇAIS 31 2. Vérifiez que le tambour est vide. Quelques minutes après la fin du programme, la fonction d'économie d'énergie éteint automatiquement l'appareil. 1. Sortez le linge de l'appareil. Après la phase de séchage, nettoyez le tambour, le joint et l'intérieur du hublot avec un chiffon humide. 12. UTILISATION QUOTIDIENNE - SÉCHAGE UNIQUEMENT AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. Cet appareil est un sèchelinge automatique. 12.1 Préparation au séchage 1.
www.aeg.com voyant du degré de séchage s'éteint et l'indicateur s'allume. À chaque fois que vous appuyez sur cette touche, la valeur augmente de 5 minutes. La nouvelle durée s'affiche. 2. Appuyez sur la touche Départ/Pause (Start/Pause) pour lancer le programme. Sur l'affichage, l'indicateur Hublot verrouillé apparaît et l'indicateur de la phase en cours commence à clignoter. L'affichage indique la durée restante du programme. 12.
FRANÇAIS 14.1 Chargement du linge • Séparez le linge en fonction des articles : blancs, de couleurs, synthétiques, délicats et en laine. • Respectez les instructions de lavage qui figurent sur les étiquettes des vêtements. • Ne lavez pas les articles blancs et de couleur ensemble. • Certains articles de couleurs peuvent déteindre lors des premiers lavages. Il est recommandé de les laver séparément les premières fois.
www.aeg.com domestique. Reportez-vous au chapitre « Dureté de l'eau ». 14.5 Dureté de l'eau Si, dans votre région, la dureté de l'eau est élevée ou modérée, il est recommandé d'utiliser un adoucisseur d'eau pour lave-linge. Dans les régions où l'eau est douce, il n'est pas nécessaire d'utiliser un adoucisseur d'eau. Pour connaître la dureté de l'eau dans votre région, contactez votre compagnie des eaux. Utilisez la bonne quantité d'adoucisseur d'eau.
FRANÇAIS 35 Lorsque le programme de séchage est terminé, retirez rapidement le linge du tambour. 15. ENTRETIEN ET NETTOYAGE AVERTISSEMENT! Reportez-vous aux chapitres concernant la sécurité. 15.1 Nettoyage extérieur Nettoyez uniquement l'appareil à l'eau chaude avec un savon doux. Séchez complètement toutes les surfaces. ATTENTION! N'utilisez pas d'alcool, de solvants ni de produits chimiques. ATTENTION! Ne nettoyez pas les surfaces métalliques avec un détergent à base de chlore.
www.aeg.com 15.6 Nettoyage du distributeur de produit de lavage Pour éviter les dépôts de lessive séchée, d'assouplissant coagulé et/ou la formation de moisissures dans le distributeur de produit de lavage, veillez à effectuer régulièrement la procédure de nettoyage suivante : 1. Ouvrez le distributeur. Appuyez sur le loquet vers le bas comme indiqué sur l'illustration, puis retirez le distributeur. 1 4. Réinstallez le distributeur de lavage dans ses rails et fermez-le.
FRANÇAIS 37 AVERTISSEMENT! • Ne retirez pas le filtre pendant que l'appareil fonctionne. • Ne nettoyez pas la pompe si l'eau de l'appareil est chaude. Attendez que l'eau refroidisse. Pour nettoyer la pompe, procédez comme suit : 1. Ouvrez le couvercle de la pompe. 2 5. Lorsque le récipient est plein d'eau, remettez le filtre en position et videz le récipient. 6. Répétez les étapes 4 et 5 jusqu'à ce que l'eau cesse de s'écouler. 7. Tournez le filtre vers la fauche pour le retirer. 1 2.
www.aeg.com 15.8 Nettoyage du tuyau d'arrivée d'eau et du filtre de la vanne Il est recommandé de nettoyer occasionnellement les deux filtres du tuyau d'arrivée d'eau et la valve pour éliminer les dépôts accumulés avec le temps : 1. Retirez le tuyau d'arrivée d'eau du robinet et nettoyez le filtre. 11. Replacez le filtre dans les guides spéciaux en le tournant vers la droite. Assurez-vous de serrer correctement le filtre afin d'empêcher toute fuite. 1 2 2 3 1 2.
FRANÇAIS 4. Lorsque vous rebranchez le tuyau à l'arrière de l'appareil, tournez-le vers la gauche ou la droite (et non en position verticale) en fonction de la position du robinet. 39 2. Démarrez le programme pour vidanger l'eau. 15.10 Précautions contre le gel Si l'appareil est installé dans un local où la température peut être négative, évacuez toute l'eau restant dans le tuyau d'alimentation et la pompe de vidange. 45° 20° 15.
www.aeg.com Si l'appareil est trop chargé, retirez des vêtements du tambour et/ou poussez sur le hublot tout en appuyant sur la touche Départ/ Pause (Start/Pause) jusqu'à ce que le voyant • - L'alimentation électrique est instable. Attendez que l'alimentation électrique se stabilise. • - Il n'y a aucune communication entre les composants électroniques de l'appareil. Éteignez puis rallumez l'appareil. Le programme ne s'est pas terminé correctement, ou l'appareil s'est arrêté trop tôt.
FRANÇAIS 41 Problème Solution possible L'appareil se remplit d'eau et se vidange immédiatement. • Vérifiez que la position du tuyau de vidange est correcte. Le tuyau est peut-être positionné trop bas. Reportez-vous au chapitre « Instructions d'installation ». L'appareil ne vidange pas l'eau. • Assurez-vous que le siphon de l'évier n'est pas obstrué. • Assurez-vous que le tuyau de vidange n'est pas tordu ni plié. • Assurez-vous que le filtre de vidange n'est pas obstrué.
www.aeg.com Problème Solution possible La durée du programme augmente ou diminue durant l'exécution du programme. • La fonction ProSense est capable d'ajuster la durée du programme en fonction du type et de la quantité de linge. Reportez-vous au paragraphe « Fonction ProSense » dans le chapitre « Utilisation quotidienne ». Les résultats de lavage ne sont pas satisfaisants. • Augmentez la quantité de produit de lavage ou utilisez-en un autre.
FRANÇAIS ATTENTION! Risque de brûlures ! Assurez-vous que la température de l'eau et le linge ne sont pas brûlants. Si nécessaire, attendez qu'ils refroidissent. ATTENTION! Risque de blessure ! Assurez-vous que le tambour ne tourne pas. Si nécessaire, attendez que le tambour cesse de tourner. Assurez-vous que le niveau de l'eau à l'intérieur du tambour n'est pas trop élevé.
www.aeg.com Programmes Charge Consom- Consomma(kg) mation tion d'eau énergéti- (litres) que (kWh) Coton Eco Programme Coton Éco à Durée approximative du programme (minutes) 8 0.90 54 278 Coton 40 °C 8 1.20 80 210 Synthétiques 40 °C 3 0.80 60 140 Délicats 40 °C 3 0.60 60 120 1.5 0.30 60 75 60 °C1).
FRANÇAIS 45 19. ACCESSOIRES 19.1 Disponible sur www.aeg.com/shop ou chez un revendeur agréé 19.3 Socle à tiroir Seuls les accessoires appropriés et agréés par AEG peuvent répondre aux normes de sécurité de l'appareil. Si les pièces ne sont pas agréées, toute réclamation sera refusée. 19.2 Kit de plaques de fixation Si vous installez l'appareil sur un socle, stabilisez l'appareil à l'aide des plaques de fixation. Lisez attentivement la notice fournie avec l'accessoire.
www.aeg.com Points de vente de rechange Industriestrasse 10, 5506 Mägenwil,Tel. 0848 848 111 Conseil technique/Vente Badenerstrasse 587, 8048 Zürich, Tel. 044 405 81 11 Garantie Nous octroyons sur chaque produit 2 ans de garantie à partir de la date de livraison ou de la mise en service au consommateur (documenté au moyen d’une facture, d’un bon de garantie ou d’un justificatif d’achat). Notre garantie couvre les frais de mains d’œuvres et de déplacement, ainsi que les pièces de rechange.
FRANÇAIS 47
157013101-A-342017 www.aeg.