FR IT Notice d'utilisation Lave-vaisselle Istruzioni per l’uso Lavastoviglie 2 26 GS60BVM
www.aeg.com TABLE DES MATIÈRES 1. INFORMATIONS DE SÉCURITÉ.................................................................................3 2. CONSIGNES DE SÉCURITÉ........................................................................................4 3. DESCRIPTION DE L'APPAREIL...................................................................................6 4. BANDEAU DE COMMANDE......................................................................................7 5. PROGRAMMES.................
FRANÇAIS 1. 3 INFORMATIONS DE SÉCURITÉ Avant d'installer et d'utiliser cet appareil, lisez soigneusement les instructions fournies. Le fabricant ne pourra être tenu pour responsable des blessures et dégâts résultant d'une mauvaise installation ou utilisation. Conservez toujours les instructions dans un lieu sûr et accessible pour vous y référer ultérieurement. 1.
www.aeg.com • • • • • • • • Respectez le nombre maximal de 13 couverts. Si le câble d'alimentation est endommagé, il doit être remplacé par le fabricant, un service de maintenance agréé ou un technicien qualifié afin d'éviter tout danger. Placez les couteaux et les couverts avec des bouts pointus dans le panier à couverts avec les pointes tournées vers le bas ou en position horizontale. Ne laissez pas la porte de l'appareil ouverte sans surveillance pour éviter tout risque de chute.
FRANÇAIS changer le fusible de la fiche électrique, utilisez le fusible : 13 amp ASTA (BS 1362). 2.3 Raccordement à l'arrivée d'eau • Veillez à ne pas endommager les tuyaux de circulation d'eau. • Avant d'installer des tuyaux neufs, des tuyaux n'ayant pas servi depuis longtemps, lorsqu'une réparation a été effectuée ou qu'un nouveau dispositif a été installé (compteurs d'eau, etc.), laissez l'eau s'écouler jusqu'à ce qu'elle soit parfaitement propre et claire.
www.aeg.com 3. DESCRIPTION DE L'APPAREIL 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Bras d'aspersion supérieur Bras d'aspersion intermédiaire Bras d'aspersion inférieur Filtres Plaque de calibrage Réservoir de sel régénérant Fente d'aération 3.1 Beam-on-Floor Le faisceau Beam-on-Floor est une lumière projetée sur le sol, sous la porte de l'appareil. • Lorsque le programme démarre, le faisceau rouge s'allume et reste allumé pendant toute la durée du programme.
FRANÇAIS 4. BANDEAU DE COMMANDE 1 1 2 3 4 5 2 Touche Marche/Arrêt Affichage Touche Delay Touche Program Touche ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Touche TimeSaver Touche XtraDry Touche RESET Voyants 4.1 Voyants Indicateur Description Voyant de fin. Voyant du réservoir de liquide de rinçage. Ce voyant est toujours éteint pendant le déroulement du programme. Voyant du réservoir de sel régénérant. Ce voyant est toujours éteint pendant le déroulement du programme. 5.
www.aeg.
FRANÇAIS Programme 1) P6 Eau (l) Consommation électrique (kWh) Durée (min) 9 - 10 1.1 - 1.3 219 - 229 9 1) Les valeurs de consommation peuvent changer en fonction de la pression et de la température de l'eau, des variations de l'alimentation électrique, de la quantité de vaisselle chargée ainsi que des options sélectionnées. 5.2 Informations pour les instituts de test Pour toute information relative aux performances de test, envoyez un courrier électronique à l'adresse : info.
www.aeg.com Dureté eau Degrés allemands (°dH) Degrés français (°fH) mmol/l Degrés Clarke Niveau de l'adoucisseur d'eau 47 - 50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.
FRANÇAIS 11 Comment régler le niveau de liquide de rinçage le voyant Remplissage du liquide de rinçage reste actif. L'appareil doit être en mode Programmation. Comment désactiver la notification du distributeur de liquide de rinçage vide 1. Pour entrer en mode utilisateur, maintenez les touches et enfoncées simultanément jusqu'à ce , , et se que les voyants mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. . , et continue à • Le voyant clignoter.
www.aeg.com que les voyants , , et se mettent à clignoter et que plus rien ne s'affiche. 2. Appuyez sur • Les voyants s'éteignent. , et 3. Appuyez sur réglage. pour modifier le = Signal sonore activé. 4. Appuyez sur la touche Marche/Arrêt pour confirmer le réglage. • Le voyant continue à clignoter. • L'affichage indique le réglage actuel : désactivé. = Signal sonore 7. OPTIONS Vous devez activer les options souhaitées à chaque fois avant de lancer un programme.
FRANÇAIS Comment activer l'option ExtraHygiene Appuyez sur ; le voyant correspondant s'allume. Si cette option n'est pas compatible avec le programme, le voyant correspondant 13 ne s'allume pas ou clignote rapidement pendant quelques secondes, puis s'éteint. L'affichage indique la durée du programme réactualisée. 8. AVANT LA PREMIÈRE UTILISATION 1. Assurez-vous que le réglage actuel de l'adoucisseur d'eau est compatible avec la dureté de l'arrivée d'eau.
www.aeg.com 8.2 Comment remplir le distributeur de liquide de rinçage A B 3. Si le liquide de rinçage déborde, épongez-le avec un chiffon absorbant pour éviter tout excès de mousse. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. Remplissez le distributeur de liquide de rinçage lorsque le voyant (A) s'allume.
FRANÇAIS ATTENTION! Utilisez uniquement un produit de lavage spécial pour lave-vaisselle. 1. Appuyez sur la touche de déverrouillage (A) pour ouvrir le couvercle (C). 2. Versez le produit de lavage sous forme de poudre ou tablette dans le compartiment approprié (B). 3. Si le programme comporte une phase de prélavage, versez une petite quantité de produit de lavage à l'intérieur de la porte de l'appareil. 4. Fermez le couvercle. Assurez-vous que le couvercle se verrouille correctement. 9.
www.aeg.com de lavage avant de lancer un nouveau programme. Fermez le robinet d'eau. Fin de programme Lorsque le programme est terminé et que vous ouvrez la porte, l'appareil s'éteint automatiquement. 10. CONSEILS 10.1 Raccordement Les conseils suivants vous garantissent des résultats de lavage et de séchage optimaux au quotidien, et vous aideront à protéger l'environnement. • Videz les plus gros résidus alimentaires des plats dans une poubelle. • Ne rincez pas vos plats à la main au préalable.
FRANÇAIS 1. Réglez l'adoucisseur d'eau sur le niveau maximal. 2. Assurez-vous que le réservoir de sel régénérant et le distributeur de liquide de rinçage sont pleins. 3. Lancez le programme le plus court avec une phase de rinçage. N'utilisez pas de produit de lavage et ne chargez pas les paniers. 4. Lorsque le programme de lavage est terminé, réglez l'adoucisseur d'eau en fonction de la dureté de l'eau dans votre région. 5. Ajustez la quantité de liquide de rinçage libérée. 6.
www.aeg.com 11.1 Nettoyage des filtres Le système de filtrage se compose de trois éléments. C B A 1. Faites pivoter le filtre (B) dans le sens antihoraire puis sortez-le. 5. Assurez-vous qu'il ne reste aucun résidu alimentaire ni salissure à l'intérieur ou autour du bord du collecteur d'eau. 6. Remettez le filtre plat à sa place (A). Vérifiez qu'il est correctement positionné sous les deux guides. 7. Remontez les filtres (B) et (C). 8. Remettez le filtre (B) dans le filtre plat (A).
FRANÇAIS ATTENTION! Une position incorrecte des filtres peut donner de mauvais résultats de lavage et endommager l'appareil. 11.2 Nettoyage du bras d'aspersion supérieur 19 4. Pour réinstaller le bras d'aspersion supérieur sur le panier, poussez le bras d'aspersion vers le haut, dans la direction indiquée par la flèche du bas, tout en le tournant vers la gauche jusqu'à ce qu'il se bloque en place.
www.aeg.com 12. EN CAS D'ANOMALIE DE FONCTIONNEMENT Si l'appareil ne démarre pas ou s'arrête en cours de programme. Avant de contacter le service après-vente agréé, vérifiez si vous pouvez résoudre le problème par vous-même à l'aide des informations du tableau. Pour certaines anomalies, l'écran affiche un code d'alarme. La plupart des problèmes peuvent être résolus sans avoir recours au service après-vente agréé.
FRANÇAIS 21 Problème et code d'alarme Cause et solution possibles Le système de sécurité antidébordement s'est déclenché. L'affichage indique • Fermez le robinet d'eau et contactez le service aprèsvente agréé. . L'appareil s'arrête et redé• C'est normal. Cela vous garantit des résultats de lavage marre plusieurs fois en cours optimaux et des économies d'énergie. de fonctionnement. Le programme dure trop longtemps. • Sélectionnez l'option TimeSaver pour raccourcir la durée du programme.
www.aeg.com 12.1 Les résultats de lavage et de séchage ne sont pas satisfaisants Problème Cause et solution possibles Résultats de lavage insatisfaisants. • Reportez-vous aux chapitres « Utilisation quotidienne », « Conseils » et au manuel de chargement du panier. • Utilisez un programme de lavage plus intense. • Nettoyez les jets des bras d'aspersion et le filtre. Reportez-vous au chapitre « Entretien et nettoyage ». Résultats de séchage insatisfaisants.
FRANÇAIS 23 Problème Cause et solution possibles Mousse inhabituelle en cours de lavage. • Utilisez uniquement des produits de lavage pour lavevaisselle. • Il y a une fuite dans le distributeur de liquide de rinçage. Faites appel à un service après vente agréé. Traces de rouille sur les couverts. • Il y a trop de sel régénérant dans l'eau utilisée pour le lavage. Reportez-vous au chapitre « Adoucisseur d'eau ». • Les couverts en argent et en acier inoxydable ont été placés ensemble.
www.aeg.com 13. CARACTÉRISTIQUES TECHNIQUES Dimensions Largeur / hauteur / profondeur (mm) 596 / 818-898 / 550 Branchement électrique1) Tension (V) 200 - 240 Fréquence (Hz) 50 / 60 bar (minimum et maximum) 0.5 - 8 MPa (minimum et maximum) 0.05 - 0.8 Arrivée d'eau Eau froide ou eau chaude 2) max. 60 °C Capacité Couverts 13 Consommation électrique Mode « Veille » (W) 5.0 Consommation électrique Mode « Éteint » (W) 0.
FRANÇAIS rechange. Les conditions de garantie ne sont pas valables en cas d’intervention d’un tiers non autorisé, de l’emploi de pièces de rechange non originales, d’erreurs de maniement ou d’installation dues à l’inobser-vation du mode d’emploi, et pour des dommages causés par des influences extérieures ou de force majeure. 15. EN MATIÈRE DE PROTECTION DE L'ENVIRONNEMENT Recyclez les matériaux portant le symbole . Déposez les emballages dans les conteneurs prévus à cet effet.
www.aeg.com INDICE 1. INFORMAZIONI DI SICUREZZA...............................................................................27 2. ISTRUZIONI DI SICUREZZA...................................................................................... 28 3. DESCRIZIONE DEL PRODOTTO............................................................................. 30 4. PANNELLO COMANDI.............................................................................................31 5. PROGRAMMI...........................
ITALIANO 1. 27 INFORMAZIONI DI SICUREZZA Leggere attentamente le istruzioni fornite prima di installare e utilizzare l'apparecchiatura. I produttori non sono responsabili di eventuali lesioni o danni derivanti da un'installazione o un uso scorretti. Conservare sempre le istruzioni in un luogo sicuro e accessibile per poterle consultare in futuro. 1.
www.aeg.com • • • • • • • • • La pressione di esercizio dell'acqua (minima e massima) deve essere compresa tra 0.5 (0.05) / 8 (0.8) bar (MPa) Rispettare il numero massimo di 13 coperti. Se il cavo di alimentazione è danneggiato, deve essere sostituito dal produttore, dal Centro di Assistenza Autorizzato o da una persona qualificata per evitare situazioni di pericolo.
ITALIANO • • • • elettrico debba essere sostituito, l’intervento dovrà essere effettuato dal nostro Centro di Assistenza autorizzato. Inserire la spina di alimentazione nella presa solo al termine dell'installazione. Verificare che la spina di alimentazione rimanga accessibile dopo l'installazione. Non tirare il cavo di alimentazione per scollegare l’apparecchiatura. Tirare solo la spina. Questa apparecchiatura è conforme alle direttive CEE. Solo per il Regno Unito e l'Irlanda.
www.aeg.com 3. DESCRIZIONE DEL PRODOTTO 1 2 3 12 11 1 2 3 4 5 6 7 10 9 8 Mulinello su cielo vasca Mulinello superiore Mulinello inferiore Filtri Targhetta dei dati Contenitore del sale Apertura di ventilazione 3.1 Beam-on-Floor Il Beam-on-Floor è un fascio di luce mostrato sul pavimento al di sotto della porta dell'apparecchiatura. • Quando il programma si avvia, la luce è rossa e rimane accesa per la durata del programma. • Una volta terminato il programma, la luce diventa verde.
ITALIANO 4. PANNELLO COMANDI 1 1 2 3 4 5 2 Tasto On/Off Display Tasto Delay Tasto Program Tasto ExtraHygiene 3 4 6 7 8 9 5 6 7 8 9 Tasto TimeSaver Tasto XtraDry Tasto RESET Spie 4.1 Spie Spia Descrizione Spia di fine. Spia del brillantante. La spia è spenta durante l'esecuzione del programma. Spia del sale. La spia è spenta durante l'esecuzione del programma. 5.
www.aeg.
ITALIANO Programma 1) Acqua (l) Energia (kWh) Durata (min) P6 9 - 10 1.1 - 1.3 219 - 229 33 1) I valori possono variare a seconda della pressione e della temperatura dell'acqua, delle variazioni dell'alimentazione elettrica, delle opzioni selezionate e della quantità di stoviglie. 5.2 Informazioni per gli istituti di prova Per le informazioni necessarie, relative alle prestazioni inviare una mail a: info.test@dishwasher-production.
www.aeg.com Gradi tedeschi (°dH) Gradi francesi (°fH) mmol/l Gradi Clarke Livello del decalcificatore dell’acqua 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.8 5 - 12 2 <4 <7 <0.7 <5 1 2) 1) Impostazioni di fabbrica.
ITALIANO finché le spie , , e iniziano a lampeggiare e il display è vuoto. 2. Premere • Le spie . , e si spengono. continua a • La spia lampeggiare. • Il display mostra l'impostazione corrente: ad es. = livello 4. – I livelli di brillantante vanno da 0A a 6A. – Livello 0 = nessuna erogazione di brillantante. non iniziano a lampeggiare e il display è vuoto. 2. Premere . • Gli indicatori spengono. , e si continua a • L'indicatore lampeggiare.
www.aeg.com 3. Premere per cambiare l'impostazione. 4. Premere il tasto On/Off per confermare l'impostazione. = Segnale acustico attivo. 7. OPZIONI Le opzioni desiderate devono essere attivate ogni volta prima dell'avvio di un programma. Non è possibile attivare o disattivare le opzioni durante l'esecuzione di un programma. Non tutte le opzioni sono compatibili tra loro. Se sono state selezione delle opzioni non compatibili, l'apparecchiatura ne disattiva automaticamente una o diverse.
ITALIANO 37 8. PREPARAZIONE AL PRIMO UTILIZZO 1. Accertarsi che il livello del decalcificatore dell'acqua attuale sia conforme alla durezza dell'acqua. In caso contrario, regolare il livello del decalcificatore dell'acqua. 2. Riempire il contenitore del sale. 3. Riempire il contenitore del brillantante. 4. Aprire il rubinetto dell’acqua. 5. Avviare un programma per rimuovere possibili residui di lavorazione presenti all’interno dell’apparecchiatura. Non utilizzare il detersivo e non caricare stoviglie.
www.aeg.com 8.2 Come riempire il contenitore del brillantante A B 3. Rimuovere l'eventuale brillantante fuoriuscito con un panno assorbente, per evitare che si formi troppa schiuma. 4. Chiudere il coperchio. Assicurarsi che il coperchio si blocchi in posizione. Riempire il contenitore del brillantante quando la spia (A) diventa trasparente. Se si utilizzano pastiglie multifunzione e le prestazioni di asciugatura sono soddisfacenti, la spia di riempimento del brillantante può essere disattivata.
ITALIANO 2. Mettere il detersivo in polvere o in pastiglie nell'apposito contenitore (B). 3. Se il programma ha una fase di prelavaggio, mettere una piccola quantità di detersivo nella parte interna della porta dell'apparecchiatura. 4. Chiudere il coperchio. Assicurarsi che il coperchio si blocchi in posizione. 9.2 Impostazione ed avvio di un programma Funzione Auto Off Questa funzione permette di ridurre il consumo di energia disattivando automaticamente l'apparecchiatura quando non è in funzione.
www.aeg.com 10. CONSIGLI E SUGGERIMENTI UTILI 10.1 Informazioni generali I seguenti suggerimenti garantiranno una pulizia e risultati di asciugatura quotidiani ottimali ed aiuteranno a salvaguardare l'ambiente. • Gettare i residui di cibo più grandi nella spazzatura. • Non prelavare le stoviglie a mano. Se necessario, utilizzare il programma prelavaggio (se disponibile) o selezionare un programma con fase di prelavaggio. • Utilizzare sempre tutto lo spazio presente nei cestelli.
ITALIANO • Sistemare le posate e i piccoli oggetti nel cestello portaposate. • Sistemare gli oggetti leggeri nel cestello superiore. In modo tale che non possano muoversi. • Prima di avviare un programma, assicurarsi che i mulinelli possano ruotare liberamente. 10.5 Prima di avviare il programma Verificare che: • I filtri siano puliti e installati correttamente. • Il tappo del contenitore del sale sia serrato. • I fori sui mulinelli non siano ostruiti.
www.aeg.com 8. Posizionare nuovamente il filtro (B) nel filtro piatto (A). Ruotarlo in senso orario finché non si blocca in posizione. 2. Estrarre il filtro (C) dal filtro (B). 3. Rimuovere il filtro piatto (A). 4. Lavare i filtri. ATTENZIONE! Un’errata posizione dei filtri può comportare scadenti risultati di lavaggio e danni all’apparecchiatura. 11.2 Pulizia del mulinello superiore Si consiglia di pulire regolarmente il mulinello superiore per evitare che lo sporco ostruisca i fori.
ITALIANO 43 11.3 Pulizia esterna • Pulire l'apparecchiatura con un panno inumidito e morbido. • Utilizzare solo detergenti neutri. • Non usare prodotti abrasivi, spugnette abrasive o solventi. 11.4 Pulizia interna 4. Per riagganciare il mulinello al cestello, premerlo nella direzione indicata dalla freccia inferiore e contemporaneamente ruotarlo in senso antiorario finché non si blocca in posizione.
www.aeg.com Problema e codice allarme Possibile causa e soluzione Non è possibile accendere l'apparecchiatura. • Verificare che la spina sia collegata alla presa elettrica. • Assicurarsi che il fusibile all'interno del quadro elettrico non sia danneggiato. Il programma non si avvia. • Controllare che la porta sia chiusa. • Se è stato impostato il ritardo, annullare l'impostazione o attendere il termine del conto alla rovescia.
ITALIANO 45 Problema e codice allarme Possibile causa e soluzione La porta dell'apparecchiatura si chiude con difficoltà. • L'apparecchiatura non è correttamente livellata. Allentare o stringere i piedini regolabili (ove previsti). • Alcune parti di pentole e stoviglie sporgono dai cestelli. Tintinnio/colpi dall'interno dell'apparecchiatura. • Le pentole e le stoviglie non sono state sistemate adeguatamente nei cestelli. Fare riferimento al libretto contenente le indicazioni per caricare il cestello.
www.aeg.com Problema Possibile causa e soluzione Su bicchieri e stoviglie riman- • La quantità di brillantante erogata è eccessiva. Regogono delle striature biancastre lare il livello del brillantante su una posizione inferiore. o striature bluastre. • È stata utilizzata una dose eccessiva di detersivo. Macchie e tracce di gocce d'acqua su bicchieri e stoviglie. • La quantità di brillantante erogata non è sufficiente. Regolare il livello del brillantante su una posizione superiore.
ITALIANO Problema 47 Possibile causa e soluzione Il calcare può depositarsi su • Il livello di sale è basso, controllare l'indicatore di pentole e stoviglie, nella vasca riempimento. o all'interno della porta. • Il tappo del contenitore del sale è lento. • L'acqua di rubinetto è dura. Fare riferimento a "Decalcificatore dell'acqua". • Anche le pastiglie multi-funzione usano il sale e impostano la rigenerazione dell'ammorbidente dell'acqua. Fare riferimento a "Decalcificatore dell'acqua".
www.aeg.com 14. CH GARANZIA Servizio clienti Servizio dopo vendita Industriestrasse 10 5506 Mägenwil Le Trési 6 1028 Préverenges Via Violino 11 6928 Manno Morgenstrasse 131 3018 Bern Zürcherstrasse 204E 9000 St. Gallen Seetalstrasse 11 6020 Emmenbrücke St. Jakob-Turm Birsstrasse 320B 4052 Basel Comercialstrasse 19 7000 Chur Vendita pezzi di ricambio Industriestrasse 10, 5506 Mägenwil,Tel. 0848 848 111 Consulenza specialistica/Vendita Badenerstrasse 587, 8048 Zürich, Tel.
ITALIANO 49
www.aeg.
ITALIANO 51
117897695-A-402016 www.aeg.