o Safety instructions Disposing of packaging and old machine Disposing of the packaging Disposing of your oki machine Important hints Operating your dishwasher economically and with regard for the environment Description of the appliance The insensible of the appliance Use Control panel Dish-washing programmed Before using your dishwasher for the first time Setting the water hardness range Tiffing with special salt Sat refill indicator The rinse-aid Setting the rinse-lad quantity to be added Adding dish was
| Palely constrictions . The satiety of AEG electrical appliances conforms to accepted rules of technology and the Appliance Safety Act. We as manufacturers, however, see ourselves as being obliged to familiarize you with the following safety instructions. Using your dishwasher for its intended purpose W Only use your dishwasher for machine washing of household crockery.
Your dishwasher in day-to-day use B Never operate your dishwasher if the electrical supply deaf, supply or drain hose, control panel, worktop. or plinth are damaged. W if there is a fault, first turn the water tap off. Then switch off your machine and pull the plug out of the socket. If there s a fixed connection, switch off or unscrew the fuse(s). W Never pull the plug out of the socket by the cable always hold the plug. M| Dishwasher repairs should only be performed by trained personnel.
_pot Disposing of the packaging Qur dishwashers require effective protective packaging in transit, though All packaging materials used are environmentally compatible and reusable. The cardboard parts are produced from recycled paper, and the wood is untreated. ! The plastics are marked as follows: >PE< for polyethylene. ¢.g. packaging foils >P8< for polystyrene. &.g. padding (essentially CFC-Free) >POM-= for polyethylene, e.g. plastic clamps.
Tt Operating your dishwasher economically and with regard for the environment Collect your dirty dishes, stack them in the dishwasher, and only wash therm when both baskets are full, making sure that the latter are never overloaded. Only then can you be sure that you are machine-washing economically and with regard for the environment. Always select the programmer corresponding to the type of crockery and degree of soiling (see *Programmer chart"). Never overdose detergents, special salt or rinse-aid.
Description of the appliance The inside of the appliance Water adjustment Upper basket Upper basket stop P Upper spray arm Lower spray arm . Central filters Large filter Salt .
Control panel {coagulate-e this fully integrated appliance the controls are located on top of the door. When selecting a programmer, the door needs to be partially opened. ON/OFF Push button @ By depressing this push button the mains-on ON (5) and the end of programmer END (8) indicator lights illuminate indicating that the washing programmer can be selected and started. 2. Programmer Selector Buttons Depress the button corresponding to the desired washing programmer (see the washing programmer char. 3.
1 il o Quantity of food scraps Type Required Pr mammograms Type of soil of load push buttons INTENSIVE | Heavily dolled, also dried up and 65° containing starch (i.e. pasta, rice, i@ D, 65°) semolina, potatoes, egy, sauces, U 65° roast). [ NORMAL Normally to heavily soiled, lase | Pots 65° dried up and/or containing starch | Pans ® = 65° {i.e. pasta, rice, semolina, potato Crockery D &5 toes, egy, sauces, roast). ECO BIO Normally to fitly soiled, not 50° dried up and starless i.e.
Recommended quantity ‘Approximate consumption values of detergent the | Cycle descriptor P baton | Energy | water on ion inside the | ;e onset in minutes | consumption consumption dispenser | "aq EKE iy | i lies 1 heaped level Rewash up to 55°C dessert dessert Main wash up to 65°C spoonful [spoonful |2 cold rinses ;.
2 Before using your dishwasher for the first time When your new dishwasher is correctly set up and installed, you must first make it ready for use. Ba fore using your dishwasher for the first time, proceed as follows: set the water softener; ~ fill the special salt container with special salt; il the rinse-lad dispenser with rinse-aid. The following sections give you more detailed information about the individual points.
Level 1 If your water is Level 1 it is already soft and therefore there is no need to use salt. In this case do not take into account the salt light on the control anal, which Illuminates when thees is no salt inside the salt container. Level 2 ¥ your water hardness is Level 2, only regenerating salt will be necessary.
With a water hardness of level 5 both adjustments must be made. Note: From Level 2 upwards, regenerating salt is to be used regularly. The relevant instructions are contained in the next section. Filling with special salt Only use salt designed specifically for use in dishwashers. Other types of salt L.e. table/cooking salt contain high percentages of other substances which may reduce the efficiency of the softener. : Caution! The packaging of dishwasher salt and detergents are often very similar.
Salt refill indicator You must refill the salt container with special salt when the salt refill indicator light SALT on the control panel illuminates. Depending on the grain size of the salt, it may be some hours fora the fight goes out again, Important: At water hardness before 4°d, you need not fil your dishwasher with special halt. In this case, the control panel continuously shows the illuminated salt refill indicator light SLAY . This implies no loss of machine function.
Setting the rinse-aid quantity to be added The correct dosage of the rinse-aid should be regulated on the basis of the shine and drying results, For this purpose, set the quantity of liquid by means of the six-position selector (C) located on the inside of the filler opening {minimum quantity is position 1, maximum quantity is position ). Use the tip of a knife or a screwdriver to rotate the selector.
The amount of detergent to be used varies depending on how soiled the dishes are and the type of dishes being washed. We recommend the amounts shown in the programmer chart, After filling the dispenser with detergent, close the lid. All the programmed with rewash require a small extra amount of detergent of approximately coffee spoon to be poured over the lid of the dispenser, as shown on the picture. . Use double this amount {10 g} if selecting the Intensive Programmer.
BIO programmed and compact powders On the basis of their chemical composition, dishwasher detergents can be classified into two basic groups: conventional, alkaline detergents with caustic components: low-alkaline compact powders with natural enzymes. The enzymes in low-alkaline compact powders have a dirt-dissolving effect and are also biodegradable.
L ane Before placing dishes in the machine, remove any large scraps of food from the plates {small bones, toothpicks, fish bones, scraps of meat and vegetables, fruit skins etc.} to avoid clogging the filters and consequently reducing performance. Open the door and side out the baskets to load the dishes. Before loading, remove all scraps of food and soak very heavily soiled pots and pans. Always arrange saucepans, cups and glasses ete. upside-down.
Cutlery basket Cutlery should be placed in the removable cutlery basket with the handles facing downwards. if the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upward, For better cleaning resits, we recommend that peons should be intermingled with other cutlery rems so that they do not nestle into one another.
The upper basket The upper basket is designed for plies (dessert plates, saucers, dinner plates diameter), salad bowls, cups and glasses; these “should be arranged as shown in the pictures. Glasses with long stems can be placed upside-down in the raised cup-racks Caution When loading the dishes, ensure that you do not cover the water infer funnel in the middle of the upper basket.
Adjusting the height of the upper basket 1f washing very large plates {over 27 om and diameter) you can load them in the lower basket after moving the upper basks to the higher position as follows: Move the front runner stops (A} of the upper basket outward and slide the basket out {Fig. 15). Refit the basket in the higher position and replace the stops (A) in their original position, Fig.
Set the programmer The selection of a programmer occurs with the door partially opened. Depress ON/OFF Push button @; the mains-on ON and end of programmer END indicator fights come on, Attention: should the END indicator light not come on, it means that the previously selected programmer hasn't finished. In this case, wait until the programmer is over or cancel the programmer (see “Te cancel the wash programmer.
o4 To cancel the wash programmer To cancel a wash programmer in progress or to reset the dishwasher if a wrong one has been selected, proceed as follows: Check that the appliance is on (ON/OFF Push button (D depressed). Simultaneously depress the QUICK WASH ‘*“I 80° and RINSE AND HOLD /ff) programmer buttons. Close the door. After a faw mind you will hear the acoustic signal. This is to tell you that the dishwasher Is reset. .
. Care instructions Internal and external cleaning * Clean the screen and controls of your dishwasher where necessary with a soft cloth and lukewarm water. Important motel Never use commercially available furniture cleaners or aggressive detergents. Cleaning the filter group Regularly check the cleanliness of the filters which are located at the bottom of the internal compartment and, if necessary, clean them. Blocked filters will compromise the washing results.
After cleaning the filters, reassemble the components by proceed mg in the reverse order. Clean the filters under running tap water. After cleaning them, insert the filters in the dishwasher by pressing them n until they click (Fig. 18). Fig. 18 Caution: The dishwasher must not be used without filters. incorrect repositioning of the filters will produce poor washing results.
Before calling our service center, please check whether you can rectify the fault yourself by following the instructions given below. Should this information be of no assistance to you in a specific case, please contact our service center. M The programmer will not start Are the fuses in the fixed wiring in order? Is your machine connected to the electricity supply? ~ Have you closed the door properly? Press the door shut., W No water flows in.
W Glasses and dishes have streaks, stripes, milky blotches, or blue-colored blooms. The rinse-aid is being overdosed. Set a lower rinse-aid dosage (see the section on "Setting the rinse-aid quantity to be dosed"). M Glasses and dishes have dried-on water drops. The rinse-aid is being under dosed. Set a higher rinse-aid dosage {see the section on *Setting the rinse-aid quantity to be dosed"). W Rust marks can be seen inside your machine. The dishwasher interior is made of stainless steel.
"Cu stonier service : ' I the section on *If you think your dishwasher is not working properly”, we have listed the most important faults which you can rectify yourself. Should you still wish to call our service center for any of the specified faults or because the appliance is being wrongly operated, the service engineer’s visit gannet be made free of charge even during the guarantee period.
Capacity 8 standard place settings including serving utensils. Allowable water pressure 5-80 N/cr® (0,5-8 Bar = Pampas. Electrical connection Details of the electrical connection are given on the rating plate. It is located on the RH inside edge of the door. c 6 This appliance complies with the following E.E.C. Directives: 73123 of 19.2.73 {Low Voltage Directive) and subsequent modifications; 897336 of 3.5.89 (Electromagnetic Compatibility Directive} and subsequent modifications.
L. Positioning Set the machine up as close as possible to a water tap and a connection for waste water. In order to ensure the door closes and seals properly, it Is necessary for the machine to stand firmly and horizontally on the floor. Adjust the screw feet upwards and downwards until the machine stands label, For built-in appliances only: Please consult the enclosed template with the installation instructions. Please note the following before installing: .
a2 proved complete hose kit {obtainable from our service center} continuously and to adequate length. Never lengthen existing hoses. important note! The supply hose must not be kinked, squashed, or twisted. Please ensure careful running. To avoid reductions in water supply to the kitchen, we recommend you to install a separate tap. Failing this, fit a branch piece to the existing water tap.
Extension hoses ) The necessary extension hoses can be obtained from specialist shops or from our technical assistance centers. The extension hose must be no longer than 2 meters and its internal diameter must be no smaller than the diameter of the hose provided. Likewise the internal diameter of the couplings used for connection to the waste outlet must be no smaller than the diameter of the drain hose.
Electrical connection WARNING THIS APPLIANCE MUST BE EARTHED. Please ensure that the voltage and current indicated in the rating plate agrees with the voltage of your electricity supply: 220/240 vomits (Le. 220/240 V AC). ¥ your appliance has been equipped with a mains lead with molded-on type plug, you must comply with the following regulations: The plug molded on to the cord incorporates a fuse. For replacement, use a 13 amps BS 1382 fuse. Only PASTA approved or certified fuses should be used.
AEG Exaggerate AG Posthaste 1036 D-90327 Nirenberg 1 © Copyright by AEG 152805 75/0 0/0998 AEG Domestic Appliances Lid Customer Care Department 58-77 High Street Sough Berkshire SL11DZ Telephone: 08705 350350
