FAVORIT 65060 Vi Der vollintegrierbare Geschirrspülautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Geräteansicht . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Bedienfeld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Vor der ersten Inbetriebnahme . . . . . . .
Garantiebedingungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kundendienststellen Service 4 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“. Bestimmungsgemäße Verwendung • Geschirrspüler ist nur zum Spülen von Haushaltsgeschirr bestimmt. • Umbauten oder Veränderungen am Geschirrspüler sind nicht zulässig. • Nur Spezialsalz, Reinigungs- sowie Klarspülmittel verwenden, die für Haushaltsgeschirrspüler geeignet sind. • Keine Lösungsmittel in den Geschirrspüler geben.
Geräteansicht Decken-Dusche Oberkorb-Sprüharm und Boden-Sprüharm Härtebereichsschalter Vorratsbehälter für Spezialsalz Behälter für Reinigungsmittel Vorratsbehälter für Klarspüler Bedienfeld Typschild Siebe Bedienfeld Zur Bedienung des Gerätes immer erst Geschirrspülertür öffnen. EIN / AUS-Taste Mit der EIN-/AUS-Taste wird der Geschirrspüler ein-/ausgeschaltet.
Zeitvorwahl einstellen 1 Multidisplay Programm-Tasten 2 3 KontrollAnzeigen Funktions-Tasten Mit den Programm-Tasten wird das gewünschte Spülprogramm gewählt.
Vor der ersten Inbetriebnahme 3 Wenn Sie 3in1 Reiniger verwenden wollen: - Lesen Sie zuerst den Abschnitt „Verwendung von 3in1 Reinigern“. - Füllen Sie weder Spezialsalz noch Klarspüler ein. Wenn Sie keinen 3in1 Reiniger verwenden, vor der ersten Inbetriebnahme: 1. Wasserenthärter einstellen 2. Spezialsalz für Wasserenthärter einfüllen 3. Klarspüler einfüllen Wasserenthärter einstellen 3 Wasserenthärter muss mechanisch und elektronisch eingestellt werden.
3 Elektronische Einstellung: 1. EIN/AUS-Taste drücken. Falls nur die LED-Anzeige einer Programmtaste leuchtet, ist dieses Spülprogramm aktiviert. Das Spülprogramm muss abgewählt werden: Funktionstasten 2 und 3 für ca. 2 Sekunden gleichzeitig drücken. Die LED-Anzeigen aller jetzt anwählbaren Programmtasten leuchten. 2. Funktions-Taste 2 und 3 gleichzeitig drücken und gedrückt halten. Die LED-Anzeigen der Funktions-Tasten 1 bis 3 blinken. 3. Funktions-Taste 1 drücken.
Spezialsalz einfüllen 3 3 10 Um den Wasserenthärter zu entkalken, muss Spezialsalz eingefüllt werden. Nur Spezialsalz verwenden, das für Haushaltsgeschirrspüler geeignet ist. Wenn Sie keinen 3in1 Reiniger verwenden, füllen Sie Spezialsalz ein: – Vor der ersten Inbetriebnahme des Geschirrspülers. – Wenn auf dem Bedienfeld die Kontrollanzeige für Spezialsalz leuchtet. 1. Tür öffnen, Unterkorb herausnehmen. 2. Verschlusskappe des Salzvorratsbehälters entgegen dem Uhrzeigersinn aufdrehen. 3.
Klarspüler einfüllen Da der Klarspüler das Spülwasser besser ablaufen lässt, erhält man fleckenfreies, glänzendes Geschirr und klare Gläser. Wenn Sie keinen 3in1 Reiniger verwenden, füllen Sie Klarspüler ein: – Vor der ersten Inbetriebnahme des Geschirrspülers. – Wenn auf dem Bedienfeld die Kontrollanzeige für Klarspüler leuchtet. Verwenden Sie nur Spezialklarspüler für Geschirrspüler und keine anderen flüssigen Reinigungsmittel. 1. Tür öffnen.
Klarspülerdosierung einstellen 3 12 Dosierung nur dann verändern, wenn auf Gläsern und Geschirr Schlieren, milchige Flecken (Dosierung niedriger einstellen) oder angetrocknete Wassertropfen (Dosierung höher einstellen) zu sehen sind (siehe Kapitel „Wenn das Spülergebnis nicht zufriedenstellend ist“). Die Dosierung kann von 1-6 eingestellt werden. Vom Werk ist die Dosierung auf „4“ voreingestellt. 1. Geschirrspülertür öffnen. 2. Entriegelungsknopf des Klarspülerfachs drücken. 3. Deckel aufklappen. 4.
Signalton ein-, ausschalten 3 Sie können einstellen, ob zusätzlich zu den optischen Anzeigen (z.B. bei Programmende, Fehlern) ein Signalton zu hören sein soll. 1. EIN/AUS-Taste drücken. Falls nur die LED-Anzeige einer Programmtaste leuchtet, ist dieses Spülprogramm aktiviert. Das Spülprogramm muss abgewählt werden: Funktionstasten 2 und 3 für ca. 2 Sekunden gleichzeitig drücken. Die LED-Anzeigen aller jetzt anwählbaren Programmtasten leuchten. 2.
Im täglichen Gebrauch Besteck und Geschirr einordnen 1 Schwämme, Haushaltstücher und alle Gegenstände, die sich mit Wasser vollsaugen können, dürfen nicht im Geschirrspüler gereinigt werden. Kunststoff- und teflonbeschichtetes Geschirr hält Wassertropfen verstärkt zurück. Daher trocknet dieses Geschirr etwas schlechter als Porzellan und Edelstahl.
Besteck einordnen 1 Warnung: Spitze Messer und scharfkantige Besteckteile müssen wegen Verletzungsgefahr in den Oberkorb gelegt werden. Damit alle Besteckteile im Besteckkorb vom Wasser umspült werden, sollten Sie: 1.Gittereinsatz auf den Besteck- 2.Gabeln und Löffel mit dem Griff korb aufstecken nach unten in den Gittereinsatz des Besteckkorbs stellen. Für größere Besteckteile, wie z.B. Schneebesen, kann eine Hälfte des Besteckgitters weggelassen werden.
Um größeres Geschirr leichter einordnen zu können, sind die beiden rechten Tellereinsätze des Unterkorbs klappbar. Tassen, Gläser, Kaffeeservice Kleineres, empfindliches Geschirr und lange, spitze Besteckteile im Oberkorb einordnen. • Geschirrteile auf und unter den klappbaren Tassenauflagen versetzt anordnen, damit das Spülwasser alle Geschirrteile erreicht. • Für hohe Geschirrteile lassen sich die Tassenauflagen hochklappen. • Wein-oder Cognacgläser in die Ausschnitte der Tassenauflagen lehnen bzw.
• Für langstielige Gläser Glasauflage nach rechts umklappen, sonst nach links weggeklappt lassen. • Die Stachelreihe links im Oberkorb ist ebenfalls zweiteilig umklappbar. Stachelreihe nicht umgeklappt: Gläser, Becher usw. in den Oberkorb stellen. Stachelreihe umgeklappt: Mehr Platz für Schüsseln.
Oberkorb in der Höhe verstellen Maximale Höhe des Geschirrs im 3 Oberkorb Unterkorb bei angehobenem Oberkorb 22 cm 30 cm bei abgesenktem Oberkorb 24 cm 29 cm Die Höhenverstellung ist auch bei beladenen Körben möglich. Je nach Modell ist das Gerät mit dem Oberkorb „Variante 1“ oder „Variante 2“ ausgestattet: Variante 1 Anheben / Absenken des Oberkorbs 1. Oberkorb ganz herausziehen. 2. Oberkorb bis zum Anschlag anheben und senkrecht absenken. Der Oberkorb rastet in der unteren bzw.
Reinigungsmittel einfüllen 1 Reinigungsmittel lösen die Verschmutzungen von Geschirr und Besteck. Das Reinigungsmittel muss vor Programmbeginn eingefüllt werden. Verwenden Sie nur Reinigungsmittel für Haushaltsgeschirrspüler. Das Fach für Reinigungsmittel ist auf der Innenseite der Tür. 1. Falls der Deckel geschlossen ist: Entriegelungsknopf drücken. Deckel springt auf. 3 2. Reinigungsmittel in den Behälter für Reinigungsmittel füllen.
Kompaktreiniger 2 Reinigungsmittel für Geschirrspüler sind heute fast ausschließlich niederalkalische Kompaktreiniger mit natürlichen Enzymen in Tablettenoder Pulverform. 50 °C-Spülprogramme in Verbindung mit diesen Kompaktreinigern entlasten die Umwelt und schonen Ihr Geschirr, denn diese Spülprogramme sind speziell auf die schmutzlösenden Eigenschaften der Enzyme im Kompaktreiniger abgestimmt.
Verwendung von 3in1 Reinigern Bei diesen Produkten handelt es sich um Reiniger mit kombinierten Reinigungsmittel-, Klarspül- und Salzfunktionen. Wenn Sie 3in1 Produkte verwenden 1. Weder Spezialsalz noch Klarspüler einfüllen. 2. Wasserenthärter auf den Wasserhärtebereich „I“ einstellen. 3. Klarspülerdosierung auf „1“ stellen. Vor Spülprogrammbeginn 3in1 Reiniger in den Behälter für Reinigungsmittel geben.
Spülprogramm auswählen (Programmtabelle) - • - • • • • 130 - 160 0,95 - 1,05 13 - 15 • • • 73 0,9 15 frisch benutzt, leicht bis normal verschmutzt - • Ess- und Kochgeschirr, temperanormal verschmutzt turempfindliches Geschirr • Dessert- und Kaffeegeschirr, emp- leicht verschmutzt findliche Gläser - ECO 50° 23 - 25 Geschirr ohne Töpfe 13 - 25 30 MIN (60°)3) 9 • 1,75 - 1,95 • 1,0 - 1,5 normal verschmutzt, angetrocknete Speisereste 0,8 Ess- und Kochgeschirr 90 - 110 AUTO (
Programmwahl Wenn Ihr Geschirr so aussieht, wählen Sie ein Intensiv-Programm. ein Normal- oder Energiesparprogramm. ein Kurzprogramm (z.B. 30min-Programm).
Spülprogramm starten 3 1. Überprüfen, ob sich die Sprüharme frei drehen können. 2. Wasserhahn ganz aufdrehen. 3. EIN/AUS-Taste drücken. 4. Gewünschtes Programm wählen. Die Programmanzeige leuchtet. Im Multidisplay wird die zu erwartende Restlaufzeit für das Programm angezeigt. Die Restlaufzeit im Multidisplay wird während des Spülvorgangs gegebenenfalls an Beladungsmenge, Verschmutzungsgrad, etc. angepasst. 5. Tür schließen. Das Spülprogramm beginnt.
Zeitvorwahl ändern: Solange das Spülprogramm nicht begonnen hat, können Sie durch Drücken der Taste Zeitvorwahl die Einstellung noch ändern. Zeitvorwahl löschen: Drücken Sie die Taste Zeitvorwahl so oft, bis im Multidisplay die Laufzeit des gewählten Programms erscheint. Das gewählte Spülprogramm beginnt sofort.
Pflege und Reinigung 1 Keine Möbelpflege- oder aggressive Reinigungsmittel verwenden. • Bedienteile des Geschirrspülers mit einem weichen Lappen und warmem, klarem Wasser reinigen. • Innenbehälter, Türdichtung und Wasserzulaufsieb (falls vorhanden) gelegentlich auf Verschmutzungen kontrollieren und gegebenfalls reinigen. Reinigung der Siebe 3 Die Siebe müssen regelmäßig kontrolliert und gereinigt werden. Verschmutzte Siebe beeinträchtigen das Spülergebnis. 1. Tür öffnen, Unterkorb herausnehmen. 2.
5. Flächensieb (3) aus dem Spülraumboden nehmen und auf beiden Seiten gründlich reinigen. 6. Flächensieb wieder einsetzen. 7. Feinsieb in den Mikrofilter einsetzen und zusammenstecken. 8. Siebsystem einsetzen und durch Schwenken des Griffs im Uhrzeigersinn bis zum Anschlag verriegeln. Darauf achten, dass das Flächensieb nicht über den Spülraumboden heraussteht. 1 Ohne Siebe darf auf keinen Fall gespült werden. Reinigung der Sprüharmdüsen 3 Düsen der Sprüharme regelmäßig auf Verstopfung prüfen.
3. Gereinigten Oberkorb-Sprüharm wieder an das Verbindungsstück schräg ansetzen: beide fest zusammendrücken, bis sie spürbar verrasten. Boden-Sprüharm 1. Boden-Sprüharm zur Entnahme aus seiner Verrastung nach oben ziehen. 2. Sprüharmdüsen reinigen. 3. Boden-Sprüharm wieder an Verbindungsstück ansetzen und fest nach unten drücken, bis er spürbar einrastet.
Was tun, wenn... Kleine Störungen selbst beheben Wenn der Signalton eingeschaltet ist, ertönen bei Störungen Warntöne. Falls während des Betriebs einer der folgenden Fehlercodes im Multidisplay angezeigt wird: – FehlercodeÅ 10 (Probleme mit Wasserzulauf), – FehlercodeÅ 20 (Probleme mit Wasserablauf), sehen Sie bitte in nachfolgender Tabelle nach. Nachdem der Fehler behoben ist, Taste des angefangenen Spülprogramms drücken. Das Spülprogramm läuft weiter.
Störung Mögliche Ursache 2 kurze Warntöne sind zu Der Siphon ist verstopft. hören, die ständig wiederholt werden, Programmanzeige des gewählten Spülprogramms blinkt, Wasserablaufschlauch das Multidisplay zeigt Feh- ist nicht korrekt verlegt. lercode Å 20 an (Spülwasser steht im Innenbehälter des Geschirrspülers). 3 kurze Warntöne sind zu hören, die ständig wiederDas Wasserschutzsystem holt werden, hat angesprochen. Das Multidisplay zeigt Fehlercode Å 30 an. Netzstecker ist nicht eingesteckt.
Wenn das Spülergebnis nicht zufriedenstellend ist Das Geschirr wird nicht sauber. • Es wurde nicht das richtige Spülprogramm gewählt. • Geschirr war so eingeordnet, dass das Spülwasser nicht alle Teile erreicht hat. Die Geschirrkörbe dürfen nicht überladen sein. • Siebe im Spülraumboden sind nicht sauber oder falsch eingesetzt. • Es wurde kein Marken-Reinigungsmittel verwendet oder zu wenig dosiert.
Entsorgung 2 2 1 32 Verpackungsmaterial Die Verpackungsmaterialien sind umweltverträglich und wiederverwertbar. Die Kunststoffteile sind gekennzeichnet, z. B. >PE<, >PS< etc. Entsorgen Sie die Verpackungsmaterialien entsprechend ihrer Kennzeichnung bei den kommunalen Entsorgungsstellen in den dafür vorgesehenen Sammelbehältern.
Technische Daten Fassungsvermögen: 12 Maßgedecke einschließlich Servicegeschirr Zulässiger Wasserdruck: 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Elektrischer Anschluß: 230 V, 10 A, siehe auch Typschild am rechten Innenrand der Geschirrspülertür. Gesamtleistung 2250 W Vollintegrierbare Geschirrspüler 5 Abmessungen: 820 - 880 x 596 x 546 (H x B x T in mm) max. Gewicht: 50 kg Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.
Hinweise für Prüfinstitute Die Prüfung nach EN 60704 muß bei voller Beladung mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Die Prüfungen nach EN 50242 müssen mit vollem Salzbehälter des Wasserenthärters, mit vollem Vorratsbehälter für Klarspüler und mit dem Testprogramm (siehe Programmtabelle) durchgeführt werden. Volle Beladung: Halbvolle Beladung: 12 Maßgedecke 6 Maßgedecke einschl. Servicegeeinschl. Servicegeschirr schirr, jeden 2.
Unterkorb mit Besteckkorb*) Besteckkorb *) Eventuell auf der linken Seite vorhandene Tassenauflagen sowie eventuell vorhandene Bierglashalter einschließlich des Gestänges entfernen.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Den Geschirrspüler nur stehend transportieren, sonst kann Salzwasser auslaufen. • Vor Inbetriebnahme den Geschirrspüler auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten.
Aufstellen des Geschirrspülers • Geschirrspüler muss standsicher und waagrecht in alle Richtungen ausgerichtet auf festem Boden aufgestellt werden. • Um Bodenunebenheiten auszugleichen und Gerätehöhe an andere Möbel anzugleichen, Schraubfüße mit einem Schraubendreher herausschrauben. • Ablaufschlauch, Zulaufschlauch und Netzkabel müssen innerhalb des Sockelrücksprungs hinten frei beweglich verlegt sein, damit diese weder abgeknickt noch abgequetscht werden können.
Anschließen des Geschirrspülers Wasseranschluss • Der Geschirrspüler kann an Kaltwasser und an Warmwasser bis max. 60 °C angeschlossen werden. • Der Geschirrspüler darf nicht an offene Warmwassergeräte und Durchlauferhitzer angeschlossen werden. Zulässiger Wasserdruck Niedrigster zulässiger Wasserdruck: 1 bar (=10 N/cm2 =100 kPa) Unter 1 bar Wasserdruck ziehen Sie bitte Ihren Installateur zu Rate.
Wasserablauf 1 Ablaufschlauch Der Ablaufschlauch darf nicht geknickt, gequetscht oder in sich verschlungen sein. Anschluss des Ablaufschlauches: – maximal zulässige Höhe: 1 Meter. – minimal erforderliche Höhe: 40 cm über der Geräteunterkante. Verlängerungsschläuche • Verlängerungsschläuche sind über den Fachhandel oder unseren Kundendienst zu beziehen. Der Innendurchmesser der Verlängerungsschläuche muss 19 mm betragen, damit die Gerätefunktion nicht gestört wird.
Elektrischer Anschluss Angaben über Netzspannung, Stromart und die erforderliche Absicherung sind dem Typschild zu entnehmen. Das Typschild ist am rechten Innenrand der Geschirrspülertür angebracht. Um den Geschirrspüler vom Netz zu trennen, Netzstecker ziehen. Achtung: – Der Stecker muss nach Aufstellung des Gerätes zugänglich bleiben. – Nach dem Einbau dürfen spannungsführende Teile und betriebsisolierte Leitungen mit dem Prüffinger nach DIN EN 60335-1 nicht berührbar sein.
Garantiebedingungen Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
Österreich Sehr geehrte Kunden! Wir, die Electrolux Hausgeräte GmbH, beglückwünschen Sie zum Erwerb eines Gerätes aus dem Electrolux Konzern. Für dieses Gerät räumen wir Ihnen, gemäß den nachstehenden Bedingungen, eine besondere Garantie ein, die Ihnen also zusätzliche Rechte gewährt. 1. Die Garantie beginnt mit dem Tag an dem das Gerät gekauft wurde und erstreckt sich über einen Zeitraum von 24 Monaten. Wir empfehlen daher, den Kaufbeleg unbedingt aufzubewahren. 2.
Belgien Unsere Geräte werden mit größter Sorgfalt hergestellt. Trotzdem kann es einmal zu einem Defekt kommen. Unser Kundendienst übernimmt auf Anfrage gerne die Reparatur, und zwar sowohl während des Garantiezeitraums als auch danach. So ist gewährleistet, dass ein Defekt nicht zu einer Verkürzung der Lebensdauer des Geräts führt. Die vorliegenden Garantiebedingungen beruhen auf der Richtlinie der Europäischen Union 99/44/ EG sowie den Bestimmungen des Bürgerlichen Gesetzbuches.
15. Mit Ausnahme der Fälle, in denen eine Haftung gesetzlich vorgeschrieben ist, wird durch die vorliegenden Garantiebedingungen jede durch den Kunden u.U. geforderte Entschädigung für über das Gerät hinausgehende Schäden ausgeschlossen. Im Falle der gesetzlich niedergelegten Haftung erfolgt maximal eine Entschädigung in Höhe des Kaufpreises des Geräts. Diese Garantiebedingungen gelten ausschließlich für in Belgien gekaufte und benutzte Geräte.
Kundendienststellen Österreich Unsere Kundendienststellen und Servicepartner Electrolux stellt Ihnen hiermit jene Partner vor, die dafür garantieren, dass wir Ihnen Top-Qualität mit unseren Kundendiensteinrichtungen jetzt und in Zukunft bieten. Unsere Kundendienststellen in den Bundesländern sind spezialisiert auf unsere Marken: AEG, Electrolux, Juno, Zanussi. Zentrale: Kundendienst Wien, Niederösterreich, nördliches Burgenland Electrolux Hausgeräte GmbH 1230 Wien, Herziggasse 9 Tel.
Ersatzteile, Zubehör und Pflegemittel Für Oesterreich: Sie können Ersatzteile, Zubehör und Pflegemittel online bestellen bei http://www.aeg-hausgeraete.at Belgien Adresse Electrolux Home Products Belgium ELECTROLUX SERVICE Bergensesteenweg 719 1502 Lembeek E-mail: consumer.services@electrolux.be 46 Consumer services Telefon 02/363.04.44 Telefax 02/363.04.00 02/363.04.
Service Wenn Sie einmal unsere Hilfe benötigen, erreichen Sie uns in Deutschland wie folgt: Bei Fragen zu Bedienung oder Ausstattung Ihres Gerätes Wenden Sie sich an den AEG-Direct Info Service: Telefon: 0180 555 4 555 (0,12 Euro/Min)** Internet: www.aeg-electrolux.de E-Mail: aeg-hausgeraete.kundenservice@aeg-hausgeraete.de Bei technischen Störungen Prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg-electrolux.