LCD Display & TV Operating Instructions CTV 4837 ST/VT CTV 4838 ST/VT
ENGLISH LCD TV A Wide Array of Screen Settings You can choose different screen settings depending on the type of program you are watching or the surrounding conditions (the lighting or the outside weather conditions). You can switch among the Sport, Movie, Music and Normal options , or you can configure the screen settings yourself. A Wide Array of Sound Settings You can choose an optimal sound setting for the type of program you are watching.
Important Safety Instructions The unit should not be placed in a built-in installation such as a book-case, limited space rack unless proper ventilation is provided. - This may cause fire by overheating or damage the unit by falling. Do not use the unit near water, oil or inflammables. - This may cause a fire. 4 Do not use the unit in direct sunlight and keep it away from heaters, stoves, and other sources of heat. - This may cause a fire.
ENGLISH Important Safety Instructions Do not use or store inflammable substances near the unit - This may cause an explosion or fire. Place the unit away from the wall for well ventilation. - This may cause a fire. Place the antenna away from the electric wire, not to touch even though it falls down by wind. - This may cause an electric shock. Do not touch the plug with wet hands. - This may cause an electric shock.
Table of Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Unpacking your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Viewing the Control Panels (Front View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Viewing the Control Panels (Rear View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Remote Control . . . . . . . . . . . . . . . . . .
Unpacking your TV ENGLISH Please make sure the following items are included with your TV set. If any items are missing, contact your dealer.
Viewing the Control Panels Front View 1 3 2 1 2 3 4 5 6 4 MENU selection Input TV/AV selection Channel selection Volume adjustment Remote control sensor Power Power Indicator Status Indicator 8 Status Red Stand-by Green Power on 5 6
ENGLISH Viewing the Control Panels Rear View Right Side 1 2 3 4 1 2 3 4 Headphone Jack (AV2) VIDEO Input (AV2) AUDIO Input (AV2) S-VIDEO Input Bottom Side 1 2 3 4 5 6 7 8 Antenna Input Jack Power Inlet with Switch 9 EURO-SCART1 Jack HDMI Input 10 EURO-SCART2 Jack RGB Video Input (PC) 11 RS-232C (For Service) PC Audio Input COMPONENT1/2 Video Input (DTV/DVD) COMPONENT1/2 Audio Input (DTV/DVD) Optical Digital Sound Output Terminal (PCM support only) 9
Remote Control 1 Power On/Off Button 13 1 2 Numeric Buttons 3 One/Two-Digit Channel Selection 4 Favorite Channel Selection (See page 28) 7 Picture Mode Selection ( ) (See page 18) 2 16 Picture Size Selection (See page 31) 3 4 5 8 Sound Mode Selection ( ) (See page 19) 9 Control the Cursor in the OSD Menu ( ) and ( ) (Channel Up / Down) (Teletext Page Up / Down, Page 33) and (Volume Up / Down) 17 TV Input Source Selection 15 18 TV Information Display (See page 25) 16 19 Sound Selection : Mono/
Inserting Batteries in the Remote Control ENGLISH You must insert or replace the batteries in the remote control when you purchase the TV or when you find that the remote control is no longer operating correctly. 1 Insert two AAA-size batteries (supplied) by matching the + and - on the batteries to the diagram inside the battery compartment. ■ Handle the remote control with care; avoid dropping it, getting it wet, placing it direct sunlight, near a heater, or where the humidity is high.
Connecting to the RCA or S-Video Input (Side (AV2)Video) Right Side of the TV (A) For RCA Input VCR Camcorder (B) For S-Video Input Video game device (A) For RCA Input 1. Connect the RCA cable to the input jacks (video+ audio L/R of side (AV2)Video) on the TV and output jacks on the external equipment such as a VCR, camcorder and some video game devices. (B) For S-Video Input 1.
ENGLISH Connecting to a DVD or DTV Set-Top Box INPUT (RCA or HDMI) Rear of the TV Video Cable DVD/DTV STB Audio Cable OR HDMI Cable 1. Connect the video cables to the Y, Pb, Pr input jacks (COMPONENT1 or 2) on the TV and the Y, Pb, Pr output jacks on the DVD or DTV Set-Top Box. 2. Connect the audio cables to the Audio L/R input jacks (COMPONENT1 or 2) on the TV and the Audio output jacks on the DVD or DTV Set-Top Box. 1.
Connecting the Headphones Right Side of the TV You can connect a set of headphones to your TV if you wish to watch a program without disturbing the other people. (See page 20) 1. Plug a set of headphones into the 3.5mm mini-jack socket on the right side of your TV. You can be heard the sound through the headphones. Note : If you use headphones for long period of time at a high volume, you may damage your hearing. Headphones are not included.
ENGLISH Connecting the Power Cord and Switching the TV On / Off 1 Connect the power cord for your TV to the power inlet on the back of your TV. 2 Connect the power cord to a properly installed 230V / 50Hz safety socket, and turn on the power switch on the back of your TV. 3 Touch the ( ) symbol, CH (56) button on the front panel of your set or press the ( ), () button on the remote control. After the green LED lamp switch on and your TV will be turned on.
Storing Channels in Memory Picture Audio Timer Install Setup Auto Tuning Italy Programme 12 System BG Option Fine Tuning OK button. S23 217.
ENGLISH Storing Channels in Memory 7 Press the ()button to select Manual Tuning and press the OK button. Picture Audio Timer Install Press the( ) button to select C (broadcast channels) or S (cable channels). Setup Auto Tuning Italy Programme 12 System BG Band Manual Tuning Fine Tuning ■ ■ Press the (¥)button to increase or decrease the channel by one. The MANUAL Search function will operate in the button direction you pressed when you press the (¥)button for more than 2 seconds.
Customizing the Picture Picture Mode Audio Timer Install Setup Option 1 Press the MENU button. 2 Press the (¥) button to select the Picture group and press the OK button. Standard Brightness 050 Contrast 050 Sharpness 007 Colour 050 Tint 050 ■ Colour Temperature ■ :Move OK:Select Picture Mode Audio MENU:Previous EXIT:Exit Timer Standard Install Setup Standard : Select when it is bright around the TV. Sport : Select when you want to get a clearer picture or watch sports.
ENGLISH Customizing the Audio 1 Press the MENU button. 2 Press the (¥) button to select the Audio group and pres the OK button. 3 Press the () button to select Balance and press the OK button. Adjust the sound balance with (¥) or () button you wished. CH+ Picture 4 Press the () button to select Volume and press the Audio Timer Install Balance 50 Volume 30 Setup Option Equalizer OK button. Adjust the sound volume with (¥) or () button you wished.
Selecting Surround Select the Surround feature to amplify the mid-to low-range sound or create surround effect. Picture Audio Timer Balance 50 Volume 30 Install Setup Option 1 ■ Equalizer Surround Press the () button to select Surround and press the OK button. On Audio Selection Main Surround On The options available in the Surround menu are displayed. 2 Press the () button to On or Off. Off 3 Press the OK button.
ENGLISH Setting the Date & Time 1 Press the MENU button. 2 Press the (¥) button to select Timer. 3 Press the () button to select Clock and press the (¥) or OK button. 4 Press the () or number (0~9) buttons to adjust the Hour CH+ ▲ and Minute. ■ ■ Adjust the Hour using the 12-hour system: AM = in the morning PM = in the afternoon/evening Picture Audio Timer Install Clock On Timer You can erase and reset the hour and minute by pressing the OK button.
Setting the Preset Time ( On / Off ) This function is available after you set the clock first. Picture Audio Timer Install Clock --:-- On Timer --:-- Off Timer --:-- Setup Option button. 3 Press the () button to select Enable. On Enable On Time AM - - : - - :Position Press the (▲▼ ) button to select ON or OFF. 01 Volume 020 MENU:Previous EXIT:Exit /OK:Select Press the MENU button.
ENGLISH Setting Restrictions On Button Input 1 Press the MENU button. Picture Audio Timer Install Setup Option Local Lock 2 Press the (¥) button to select the Option group and press Off OSD Setting No Signal Power Off 20 the OK button. No Operation Power Off 180 Noise Reduction On Viewell Engin 3 Press the () button to select Local Lock and press the OK button. 4 Press the () button to select Off or On and :Move OK:Select MENU:Previous EXIT:Exit press the OK button.
No Signal Auto Power Off Automatically turns the power off if there is no broadcast signal or button pressed for some time. Picture Audio Timer Install Setup Option Local Lock Off OSD Setting 0:OFF, 1~20 No Signal Power Off 20 1 2 Press the (¥) button to select the Option group and press the OK button. No Operation Power Off 180 Noise Reduction On Viewell Engin 3 Press the () button to select No Signal Power Off . MENU:Previous EXIT:Exit No Signal Power Off :Adjus Press the MENU button.
ENGLISH Viewell Engine 1 Press the MENU button. Picture Audio Timer Install 2 Press the (¥) button to select the Option group and press Option Off OSD Setting No Signal Power Off 20 the OK button. Viewell Engin On 3 Press the () button to select Viewell Engine and press No Operation Power Off 180 Noise Reduction On Viewell Engin Off Demo On the OK button.
Adjusting the Screen Geometry This function does not work in DVI-Digital mode. (The choose of features is addicted to the mode.) Auto Geometry Adjust 1 Picture Audio Timer Install Setup Option Language English Geometry 2 Press the (¥) button to select the Setup group and press the OK button. Aspect Mode Auto Favourite Channel PIP Size PIP Position 3 Press the () button to select the Geometry group and press the OK button.
Adjusting the Screen Geometry ENGLISH This function does not work in DVI-Digital mode. Adjusting the Phase 1 Press the MENU button. Picture Audio Timer Install Setup Option Language 2 Press the (¥) button to select the Setup group and press Geometry the OK button. 3 Press the () button to select the Geometry group and English Geometry Auto Geometry Adjust Aspect Mode Auto H. Size 0 Favourite Channel H. Position 50 PIP Size V.
Watching your Favorite Channels Chose when deleting the favourite channels registered in the buttons 1 to 5. Picture Audio Timer Install Setup Option Language English 1 Press the MENU button. Geometry Aspect Mode Auto Favorite Channel Favourite Channel 1: - - - - - PIP Size 2: - - - - - PIP Position 3: - - - - - Set ID 4: - - - - - Factory Preset the OK button.
Display the Picture in Picture ( PIP ) ■ 1 This function is available only with the remote control. You can watch another device's image in the PIP while watching the TV, PC or in VIDEO the main image. ENGLISH ■ Press the PIP( ) button. There are 2 modes of window : PIP, POP Whenever you press this button, PIP window mode will be changed. The PIP window is changed in the following order : PIP➔ POP ➔ Off CH + CH - < Off > < PIP > 2 Press the ( the PIP.
Display the Picture in Picture ( PIP ) Changing the PIP Size Picture Audio Timer Install Setup Option Language PIP Size 1 English Press the ( ■ Geometry Aspect Mode Auto Favourite Channel ) button on the remote control. The PIP will change free different size whenever you press the button.
Changing the Picture Size ■ 1 You can change the screen size according to the picture aspect ratio. Choose the optimum one from the following ASPECT modes. The Auto aspect mode is fixed at Full when you are using the TV as a PC screen. Press the ( ENGLISH ■ ) button on the remote control. When you are viewing the Main image: The image will change as shown below whenever you press this button.
Teletext Functions The Teletext page of most TV channels provide information such as TV programme times, News bulletins, Weather forecasts, Travel information, or Sports results. Functions of the teletext C A B Part D E F Display Contents A Selected page number. B Broadcast Station identity. C Current page number or searching status. D Date and time. E Text information. F FASTEXT information.
ENGLISH Selecting a Special Teletext Functions Selecting a Special Teletext Functions MENU REVEAL Functions Displays concealed text such as answer to quiz games. To return to normal viewing, press this button again. SUB-PAGE Displays a secondary page by entering its number. CH + CH - Displays the next page. Displays the previous page. HOLD When the secondary pages are displayed in sequence, press the HOLD button. To freeze the current display page, press the HOLD button again to resume.
Connecting to the PC (DVI) RGB INPUT Rear of the TV PC Audiocabel (not included) 15Pin D-Sub Cabel (not included) ◆ Connect the 15Pin D-Sub Cable to the RGB INPUT port on the TV and output port on the Rear of the PC. To use the TV as a PC Display 1 Turn the PC on. 2 Press the PC or ( ) button on the remote control to select the PC. 3 Set up the PC software. (See page 35) 4 Adjust the screen in PC Mode.
ENGLISH Setting the PC Software 1 First, click on Settings on the Windows Start menu and click on "Control Panel". 2 Double click on the Display icon. 3 Click on the Settings tab on the display dialog-box. 4 Adjust the resolution up to 1366 x 768 pixels. 5 Click the Advanced button and click the Monitor tab on the dialog-box. Set the vertical-frequency to 60Hz and then click the OK button. ☛ - Maximum resolution depends on the Video Card.
Standard Display Mode If the signal from the system equals the standard signal mode, the screen will adjust automatically. If the signal from the system does not equal the standard signal, adjust the display mode as shown below referring to your video card instructions. Otherwise there will be no picture or only power may turn on.
ENGLISH Pin Configuration PC Input Connector (15Pin D-Sub) Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PC IN Red (R) Green (G) Blue (B) Grounding Grounding (DDC) Red (R) Grounding Green (G) Grounding Blue (B) Grounding Reserved Sync Grounding Grounding Data (DDC) Horizontal Sync Vertical sync Clock (DDC) 37
Troubleshooting For TV 38 No picture or sound. ☛ Make sure the TV is plugged in. ☛ Make sure the power cord is connected to the consent correctly. ☛ Check the power failure. Screen is black. ☛ Make sure the external signal source mode is selected. ☛ Press the TV/AV button to change to TV. Picture is OK but there is no sound. ☛ Press the Mute button. ☛ Check another channel. ☛ Press the button to increase the volume. Poor sound quality.
ENGLISH Troubleshooting For Monitor "No signal" message ☛ Check if the signal cable(RGB Cable) is properly connected to the computer. (See page 34) "Out of range" message ☛ This message may appear when the resolution and frequency of the video card in the computer are out the range of the TV. Select the proper resolution and frequency for the TV. (See page 36) Picture rolls down vertically. ☛ Check if the signal cable (RGB Cable) is properly connected to the computer.
Specifications CTV 4837 ST/VT Model name LCD TV/ VIDEO 37” Diagonal 819.6 mm (H) x 460.8 mm (V) Pixel Pitch 0.20 mm (H) x 0.60 mm (V) Pixel Number 1366 x 768 (WXGA) Type a-Si TFT active matrix Brightness 500 cd / m2 Contrast Ratio 1200 : 1 Viewing Angle 176 (H) / 176 (V) Colour System PAL / SECAM / AV NTSC Sound System COMPONENT SCART Size Display Size Video System CVBS, S-VIDEO Y / Pb / Pr COMPONENT1,2 : 480i/p, 576i/p, 720p, 1080i Video Input 1.
ENGLISH Specifications CTV 4838 ST/VT Model name LCD TV/ VIDEO 42” Diagonal Display Size 930.25 mm (H) x 523.01 mm (V) Pixel Pitch 0.227 mm (H) x 0.681 mm (V) Pixel Number 1366 x 768 (WXGA) Type a-Si TFT active matrix Brightness 500 cd / m2 Contrast Ratio 1200 : 1 Viewing Angle 176 (H) / 176 (V) Colour System PAL / SECAM / AV NTSC Sound System COMPONENT SCART Size CVBS, S-VIDEO Y / Pb / Pr COMPONENT1,2 : 480i/p, 576i/p, 720p, 1080i Video Input 1.
Guarantee / Environment This device has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations. Subject to technical changes without prior notice! Guarantee The device supplied by our Company is covered by a 24 month guarantee starting on the date of purchase (receipt).
ENGLISH Memo 43
