INSTRUCTION- AND INSTALLATION BOOK GB Gas hob 6561 G-m 1 GB 949600555
Your New Appliance Thank you for purchasing an AEG appliance. To enable you to use your new hob efficiently and safely, please read this instruction book carefully before installing or using the appliance, and retain for future reference. Should the hob be transferred to a new owner please ensure this instruction book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings.
Table of contents Contents Page no For the user Your new appliance ...................................................................................... 2 Safety information ........................................................................................ 4 Description of the product ......................................................................... 5 Operation instructions ................................................................................ 6 Inner- and outer burner ring .....
Safety information Never use plastic or aluminium dishes on the hob. These warnings are provided in the interests of your safety. Ensure you fully understand them before installing or using the appliance. Your safety is of paramount importance. If you are unsure about the meaning of these warnings contact the Customer Care Department for assistance. Never leave the hob unattended while deep fat frying, or heating fats and oils.
Description of the product Air intake Gas burner Control knob Air intake The primary air intake aperture must never be blocked by objests of any kind at any time.
Operation intructions Burner markings Symbols at each operating knob indicate which burner is adjusted with the control knobs. Left front burner Left back burner Right back burner Right front burner Panel markings Each operating knob has a ring showing the scale of markings. Off.
Burner cover/inner burner ring/outer burner ring Together with the inner burner ring the outer burner ring forms a space where the final mixture of gas and air takes place in order for the gas burn correctly. Cover Burner ring Please note: It is very important that the inner burner ring/outer burner ring is placed correctly, together with the cover. See installation of the wok burner.
Ignition 1. Depress and turn the control knob for the burner to the left to max. flame . (Ignition position) 2. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. If it is not possible to connect the unit to mains, a match may be used to ignite the burner. 3. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo-couple (thermo sensor ready). 5.
Maintenance and cleaning For reasons of hygiene and safety, the cooking zones must be kept clean. Grease stains and spilled food generate smoke when heated, and can even cause fire. Splashguard The splashguard can be removed to make it easier to clean the surface. What to do: 1. Hold the splashguard as shown in the diagram. 2. Lift the splashguard straight up 3. Clean the top surface as described in “cleaning the steel surface”. Be aware of the two retaining pegs, which are sharp. 4.
3. Wipe the ceramic hob clean with a damp cloth or kitchen towel. Tough stains can be removed by rubbing the stain hard with kitchen towel. 4. Wipe off remaining cleaning agent with a damp cloth. 5. Wipe with a dry cloth, if required. Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid cream. Always clean the steel in the direction of the steel finish.
The gas burner The operating panel with knob, pan support and burner covers/rings are to be cleaned with ordinary cleaning agents. Do not use any kind of scouring powder. Avoid saucepans boiling over. If water gets into the burner, this should be removed before re-igniting the burner, e.g. with a no-fluff cloth.
Technical data Type of gas Adjusted to natural gas: G20-20 mbar 240 V 1N + PE Category and pressures UK: II 20 mbar - 28/37 mbar 2H3+ N L1 Max. nominal load Q na HS: Small sized burner= 1,1 kW x 1 Medium sized burner = 1,9 kW x 2 Large sized burner = 2,7 kW x 1 Total= 7,6 kW The hob must be connected via an external switch with a contact gap of min. 3 mm (the main switch may be used) FSD The unit features fully-secured gas taps (thermo-fuse).
Important safety requirements This hob must be installed by qualified personnel to the relevant British Standards. This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Any gas installation must be carried out by a CORGI registered installer. Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions.
Gas connection Connection to the gas supply should be with either rigid or semirigid pipe, i.e. steel or copper. The connection should be suitable for connection to RC ½ (½ BSP male conical thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installaion. Ensure that the main connection pipe does not exert any strain on the hob.
Mounting Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. Headroom The distance to any shelves or tops of a cabinet under the hob is to be at least 47 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the table top.
It is not necessary to attach the reinforcement beam to the table surface, as it is held in place by a specially designed moulding, which is incorporated in the hob units flanges. Installation in work tops with a base unit underneath If the hob is to be installed on top of a base unit, a board must be mounted underneath the hob (e.g. 16 mm chip board). Min. 140 mm Min. 16 mm Aluminium-tape Seal all joints with aluminium tape. The board can be mounted as shown in the diagram.
Do not install the hob above drawers.
Do not install the hob above drawers. Combined installation with oven If the oven is placed directly under the dropinette a metal plate must be installed in between. The metal plate is included in the installation kit intended for this combination. The kit, product number 949 600 970, can be ordered from your kitchen appliance dealer. This gas hob can be combined with AEG Competence ovens with a maximum power of 3,7 kW.
The unit´s externally measured length 145 mm: Cooker hood 290 mm: Two-zone ceramic-top electric hob Two-burner gas hob Grill Fryer Wok 580 mm: Four-zone ceramic-top electric hob Four-burner gas hob 725 mm: Four-zone ceramic-top electric hob Installation of a single unit When mounting a single unit, be it a half-or full size unit, in a table surface which is thicker than 30 mm, it is necessary to make a special notch in both sides of the cut-out hole, as shown in the adjacent drawing.
Gas installation In accordance with local requirements for domestic gas cooking appliances. Gas installation must only be carried out by an authorised person. For gas types see technical data. Gas connection The gas intake is situated at the lower rear of the appliance. The intake has a ½" conical pipe thread (see fig 1) If the appliance is to be connected to a gas cylinder, conversion with the optional modification kit will be necessary. Pressure test The unit should be pressure-tested at Max. 150 mbar.
Something not working If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. IMPORTANT: If you call out an engineer to a fault caused by incorrect use or installation, a charge will be made even if the hob is under guarantee. Sympton: Solution There is no spark when lighting the gas Check hob is connected to the electricity supply. Check the fuse and replace if necessery.
Service & spare parts In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will automatically be routed to the Service Centre covering your post code area. In-guarantee customers should ensure that the recommended checks under the heading "Something Not Working" have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.
Guarantee conditions 6. The purchaser's statutory rights are not affected by this guarantee. AEG offer the following guarantee to the first purchaser of this appliance: 1. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. 2. The guarantee covers all parts or components which fail due to faulty workmanship or faulty material.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local service organisation is aware of your move and able to look after you and your appliances.
325 88-3700 Rev.
