X-MOVE LED PLUS User Instructions A.D.J. Supply Europe B.V. Junostraat 2 6468 EW Kerkrade The Netherlands www.americandj.eu Rev.
Contents GENERAL INFORMATION ........................................................................................................................................................ 3 GENERAL INSTRUCTIONS ........................................................................................................................................................ 3 FEATURES ...............................................................................................................................................
INTRODUCTION GENERAL INFORMATION Unpacking: Thank you for purchasing the X-Move LED Plus™ by American DJ ® . Every X-Move LED Plus™ has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact.
SAFETY PRECAUTIONS For Your Own Personal Safety, Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit! • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture • Do not spill water or other liquids into or on to your unit. • Be sure that the local power outlet match that of the required voltage for your unit. • Do not attempt to operate this unit if the power cord has been frayed or broken.
SET UP (continued) the end, or anywhere in the middle. Therefore, the first fixture controlled by the controller could be the last fixture in the chain. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): The X-Move LED Plus™ can be controlled via DMX-512 protocol. The X-Move LED Plus™ is be a eight channel DMX unit.
SET UP (continued) Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
SYSTEM MENU CHART DMX 515 Address setting Show Mode 1 Showe Mode 2 Showe Mode 3 Show Mode 4 Slave Mode „Normal” Slave mode „2 Light Show” Sound Mode „ON” Sound Mode „OFF” Blackout Mode „Yes Blackout” Blacout Mode „No Blackout” Pan Normal Pan Inversion Tilt Normal Tilt Invesion LED on LED off Normal Inversion Focus Adjust Self-Test TemperatureTest Fixture Hours Software Version Reset A.D.J. Supply Europe B.V. – www.americandj.
SYSTEM MENU System Menu: When making adjustments you can press ENTER to confirm your setup or you can wait 8 seconds for automatic setup. To exit without making any adjustments press the MENU button. ADDR - DMX Address Setting. 1. Tap the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER. 2. The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired address. Press ENTER to set your desired DMX address.
1. Tap the MENU button until “DISP” is displayed, press ENTER. 2. Press ENTER to “flip” the display. Press ENTER to “flip” it again. Press ENTER when you have made your desired setup. SYSTEM MENU (continued) FADJ - This function will give you a you are able to focus the lens for a clear LED output. 1. Tap the MENU button until “FADJ” is displayed, press ENTER. The fixture will turn a different way each time the ENTER button is pressed. 2.
OPERATION Operating Modes: The X-Move LED Plus™ can operate in three different modes. In each mode you can run the fixture as a stand alone fixture or in a master/slave configuration. This next section will detail the differences in the operating modes. • Sound Active mode The fixture will react to sound, chasing through the built-in programs. • Show mode The fixture will run one of four shows that you choose.
UC3 CONTROL The optional UC3 Controller (not included) may be used to control different functions including blackout. Stand By Blackout the unit Function 1.Sync. Strobe 2. Async strobe 3. Sound Strobe Show1-4 1. Select Color 2. Select Gobo Mode Sound (LED OFF) Show( LED Slow Blinking) LED ON A.D.J. Supply Europe B.V. – www.americandj.
DMX TRAITS Channel 1 Value Function 0 - 255 PAN 0 - 255 TILT COLORS WHITE ORANGE BLUE GREEN YELLOW PINK LIGHT BLUE LIGHT GREEN LIGHT YELLOW RAINBOW EFFECT SLOW - FAST SOUND ACTIVE 2 3 0 - 14 15 - 29 30 - 44 45 – 59 60 - 74 75 - 89 90 - 104 105 - 119 120 - 127 128 - 254 255 4 0-7 8 - 14 15 - 21 22 - 28 29 - 36 37 - 43 44 - 50 51 - 57 58 - 63 64 - 71 72 - 78 79 - 85 86 - 92 93 - 100 101 - 107 108 - 114 115 - 121 122 - 127 128 - 254 255 5 0-7 8 - 15 16 - 131 132 - 139 140 - 180 181 - 190 191 - 231 232
FUSE REPLACEMENT Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.
SPECIFICATIONS Model: X-Move LED Plus™ Voltage*: Power Consumption Dimensions: 115v/60Hz or 230v/50Hz 49W 8”(L) x 7.5”(W) x 12.5”(H) 205mm x 190mm x 320mm RGB + White 10 Lbs. / 4.
ROHS and WEEE Dear Customer, ROHS – A great Contribution to the Conservation of Environment The European Union has adopted a directive on the restriction / prohibition of the use of hazardous substances. This directive, referred to as ROHS, is a frequently discussed topic in the electronic industry.
A.D.J. Supply Europe B.V. Junostraat 2 6468 EW Kerkrade The Netherlands www.americandj.eu A.D.J. Supply Europe B.V. – www.americandj.