MEASUREMENT FOUNDATION Operating manual Laser level Model: CUBE 360 Manufacturer: ADAINSTRUMENTS Address: WWW.ADAINSTRUMENTS.
CUBE 360 Table of contents 1. Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Technical requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Safety requirements and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 4. Order working . . . .
CUBE 360 vertical line 1. CAUTIONS Laser level ADA CUBE 360 model - is an up-to-date functional and multi-prism device designed for indoor and outdoor performance. The device emits: one horizontal laser line (beam scan angle of 360°) one vertical laser line (beam scan angle of 110°); down point laser. Do not look at the laser beam! Do not install the device on the eye level! Before using the device, do read this operating manual! 90° horizontal line 2. TECHNICAL REQUIREMENTS 2.1.
CUBE 360 2 2.2. FEATURES 1. Laser lines on/off 2. Indoor/outdoor operating mode 3. Battery compartment 4. Tripod mount 1/4’’ 5. Compensator switch (ON/X/OFF) 6. Vertical laser window 7.
CUBE 360 2.3. SPECIFICATIONS Laser Horizontal line 360°/vertical line Light sources 2 laser diodes with laser emission wave length of 635 nm Laser safety class Class 2, <1mW Accuracy ±3 mm/10 m Self-leveling range ±4° Operating range with/without receiver 70/20 m Power source 3 alkaline batteries, AA type Operation time Approx.
CUBE 360 3. SAFETY REQUIREMENTS AND CARE Follow safety requirements! Don’t face and stare at laser beam! Laser level is an accurate Instrument, which should be stored and used with care. Avoid shaking and vibrations! Store the Instrument and It’s accessories only In the carrying case. In case of high humidity and low temperature, dry out the Instrument and clean It after the usage. Do not store the Instrument at a temperature below -20°C and above 50°C, otherwise the Instrument can be out of action.
CUBE 360 polarity, the put the cover back. 2. Set the compensator locking grip 5 into ON position, two laser beams will be on. If the switch is ON,that means the power is on and the compensator is working. If the switch 5 is in intermediate position, that means the power is opened,the compensation is still locked, but it will not warn if you issue the slope. It’s the hand-mode. If the switch 5 is OFF, that means that the instrument is off, the compensator is also locked. 3.
CUBE 360 To check the accuracy of line laser level To check the accuracy of line laser level (slope of plane) Set up the instrument between two walls, the distance is 5m.Turn on the Line Laser, and mark the point of cross laser line on the wall. Rotate the instrument by 180° and mark the point of cross laser line on the wall again. Set up the instrument 0,5-0,7m away from the wall and make, as described above, the same masrks.
CUBE 360 To check level Choose a wall and set laser 5m away from the wall. Turn on the laser and cross laser line is marked A on the wall. Find another point M on the horizontal line, the distance is around 2.5m. Swivel the laser, and another cross point of cross laser line is marked B. Please note the distance of B to A should be 5m. Measure the distance between M to cross laser line. To check plumb Choose a wall and set laser 5m away from the wall. Hang a plumb with the length 2.5 m on the wall.
CUBE 360 5. APPLICATION 6.
CUBE 360 CARE AND CLEANING Please handle measuring instrument with care. Clean with soft cloth only after any use. If necessary damp cloth with some water. If instrument is wet clean and dry it carefully. Pack it up only if it is perfectly dry. Transport in original container/case only. Note: During transport On/Off compensator lock (5) must be set to position “OFF”. Disregard may lead to damage of compensator.
CUBE 360 LASER CLASSIFICATION The instrument is a laser class 2 laser product accortding to DIN IEC 60825-1:2007. It is allowed to use unit without further safety precautions. SAFETY INSTRUCTIONS Please follow up instructions given in operators’ manual. Do not stare into beam. Laser beam can lead to eye injury (even from greater distances). Do not aim laser beam at persons or animals. The laser plane should be set up above eye level of persons. Use the instrument for measuring jobs only.
CUBE 360 During the warranty period, and upon proof of purchase, the product will be repaired or replaced (with the same or similar model at manufactures option), without charge for either parts of labour. In case of a defect please contact the dealer where you originally purchased this product. The warranty will not apply to this product if it has been misused, abused or altered.
WARRANTY DOESN’T EXTEND TO FOLLOWING CASES: 1. If the standard or serial product number will be changed, erased, removed or wil be unreadable. 2. Periodic maintenance, repair or changing parts as a result of their normal runout. 3. All adaptations and modifications with the purpose of improvement and expansion of normal sphere of product application, mentioned in the service instruction, without tentative written agreement of the expert provider. 4. Service by anyone other than an authorized service center.
WARRANTY CARD Name and model of the product ________________________________________________ Serial number ________________date of sale_______________________ Name of commercial organization _____________________stamp of commercial organization Warranty period for the instrument explotation is 24 months after the date of original retail purchase. During this warranty period the owner of the product has the right for free repair of his instrument in case of manufacturing defects.
Certificate of acceptance and sale __________________________________________________________________________ __________________________________________________________________________ ___________________________________________________________№_____________ name and model of the instrument Corresponds to ______________________________________________________________ designation of standard and technical requirements Data of issue _______________________________________________________________ Stamp of qu
