User Manual
Table Of Contents
ADCP-75-124 • Issue B • April 2002 • Section 3: Host Unit Installation
Page 3-1
©
2002,
ADC
Telecommunications,
Inc.
SECTION 3: HOST UNIT INSTALLATION
1 BEFORE STARTING INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
1.1 Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
1.2 Unpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
2 OSP FIBER CABLE INSTALLATION GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
3 WDM MOUNTING PROCEDURE (OPTIONAL ACCESSORY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
4 HU MOUNTING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6
5 CHASSIS GROUND CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
6 COAXIAL CABLE CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8
7 OPTICAL CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
7.1 Optical Connections Without WDM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
7.2 Optical Connections With WDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
8 CONTROLLER AREA NETWORK CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
9 SERVICE INTERFACE CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
10 EXTERNAL ALARM SYSTEM CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
11 DC POWER CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
_________________________________________________________________________________________________________
1 BEFORE STARTING INSTALLATION
This
section
provides
the
installation
procedures
for
the
HU,
the
WDM
mounting
shelf
(accessory
item),
and
the
WDM
(accessory
item).
Installation
of
the
RU
cabinet
and
RU
electronic
modules
may
proceed
separately
from
installation
of
the
HU.
The
installation
procedures
for
the
single
band
remote
cabinet
are
provided
in
the
Digivance
Long-Range
Coverage
Solution
Single
Band
Remote
Cabinet
Mounting
Instructions
(ADCP-75-117)
which
are
shipped
with
the
cabinet.
The
installation
procedures
for
the
STM
and
LPA
electronic
modules
are
provided
in
the
Digivance
Long-Range
Coverage
Solution
Remote
Unit
Installation
Instructions
which
are
shipped
with
the
STM.
When
all
units
of
the
Digivance
LRCS
have
been
installed,
refer
to
Section
4
of
this
manual
for
the
system
turn-up
and
test
procedures.
Before
beginning
the
installation,
review
the
system
design
plan
with
the
system
engineer.
Make
sure
each
equipment
installation
site
is
identified
and
located
and
all
cable
runs
are
mapped
out.
1.1 Tools and Materials
The
following
tools
are
required
to
complete
the
procedures
in
this
section:
•Box
cutter
• Pencil
or
scribe
•Medium
size
flat-bladed
screwdriver
• Phillips
screwdriver
(#2)
Content Page