Installation Instructions

ManualsBrandsadapt ManualsCabinet Organization & Accessoriesadapt.™ 14" Stainless Steel Tip-Out Tray Drawer Organizer

Face-Frame Frameless

NOTE

This product is designed to mount

to the rear of a face panel /

drawer panel in front of a sink.

The product may be mounted in a

face-frame or frameless cabinet.

Follow only the steps for your type

of cabinet.

ITEM

QTY

1 Left, 1 Right

REQUIRED TOOLS (not included)

Drill

/32” Drill bit

Phillips Screwdriver

Pencil

DESCRIPTION

Sink Tray

Hinge

Flat Head Screw

Hinge Template

Extension Template

Sink Tray Screw

IMPORTANT

READ ALL INSTRUCTIONS AND CHECK ALL PARTS BEFORE BEGINNING INSTALLATION

PARTS LIST

EXTENSION

TEMPLATE

FRAME PERIMETER

FRAMELESS

DRAWER EDGE

FRAMELESS

DRAWER EDGE

EXTENSION

TEMPLATE

FRAME PERIMETER

FRAMELESS

DRAWER EDGE

FRAMELESS

DRAWER EDGE

PART NUMBER

SS-10.1039 (LH) SS-10.1040 (RH)

SS-10.1041

SS-10.1042

DO NOT RETURN TO THE RETAILER

If you have any questions, please contact Customer Care at

1-800-721-4191

Monday – Friday 8-5 Central Time

4814120 - MEN0643 14” Tip-Out Tray Organizer

4814121 - MEN0644 11” Tip-Out Tray Organizer

Summary of content (7 pages)

PAGE 1
4814120 - MEN0643 14” Tip-Out Tray Organizer 4814121 - MEN0644 11” Tip-Out Tray Organizer DO NOT RETURN TO THE RETAILER If you have any questions, please contact Customer Care at 1-800-721-4191 Monday – Friday 8-5 Central Time PARTS LIST 3 4 5 6 FRAME PER ER PERIMET ITEM DESCRIPTION L FRAME FRAMELESS GE DRAWER ED FRAMEL ESS DRAW ER EDG E R EXTENSION TEMPLATE IMETER 2 FRAMELESS GE DRAWER ED 1 EXTENSI O TEMPLA N TE FRAMEL ESS DRAW ER EDG E QTY PART NUMBER 1 - 1 Sink Tray 2 Hinge 3
PAGE 2
Face-Frame Cabinet - START HERE STEP 1 Using a pencil, from the inside of your cabinet, trace around the frame perimeter on the sink front panel. Mark a “T” in the center to indicate the top of the panel. NOTE: A short pencil will provide for easier marking. STEP 2 Remove the sink front panel. Take care not to damage it. STEP 3 Place the provided Hinge Template on the face frame as shown and mark the (2) holes with a pencil. Drill pilot holes using a 3/32” drill bit. Repeat for the other side.
PAGE 3
STEP 5 Lay the Sink Tray on the sink front panel and position it 1/4” below and parallel with the top pencil line and centered side-to-side on the sink front panel. Hold Sink Tray in place and mark the slotted holes at top. STEP 6 Once all the holes are marked, drill pilot holes using a 3/32” bit in all (6) marked locations. NOTE: Be careful to NOT drill through the sink front panel. STEP 7 Attach the Hinge marked “R” to the lower left corner of the sink front panel using (2) provided Flat Head Screws.
PAGE 4
STEP 9 Take the sink front panel and line it up with your cabinet opening. Extend each Hinge and attach the Hinges to the face frame using (2) provided Flat Head Screws for each Hinge. STEP 10 Remove the protective film from the Sink Tray. Install the Sink Tray onto the Sink Tray Screws and tighten down the screws.
PAGE 5
Frameless Cabinet - START HERE STEP 1 Remove the sink front panel. Take care not to damage it. Remove any brackets from the panel. Mark the rear of the panel with a “T” to indicate the top of the panel. STEP 2 Place the provided Hinge Template in the cabinet as shown and mark the (2) holes with a pencil. Drill pilot holes using a 3/32” drill bit. Repeat for the other side.
PAGE 6
STEP 4 Lay the Sink Tray on the sink front panel and position it 1/4” + the cabinet top thickness below and parallel with the top and centered side-to-side on the sink front panel. Cabinet Top Thickness Cabinet Top Thickness + 1/4” Hold Sink Tray in place and mark the slotted holes at top. STEP 5 Once all the holes are marked, drill pilot holes using a 3/32” bit in all (6) marked locations. NOTE: Be careful to NOT drill through the sink front panel.
PAGE 7
STEP 8 Take the sink front panel and line it up with your cabinet opening. Extend each Hinge and attach the Hinges to the cabinet wall using (2) provided Flat Head Screws for each Hinge. STEP 9 Remove the protective film from the Sink Tray. Install the Sink Tray onto the Sink Tray Screws and tighten down the screws.