Installation Instructions

ManualsBrandsadapt ManualsCabinet Organization & Accessoriesadapt.™ Soft-Close 15" Chrome Lids and Pans Organizer

MODEL

Minimum

Height

(a)

Minimum

Depth

Minimum

Opening

Cabinet Size for

Side Mounting

(b)

15 Inch 18” 22-

/16” 15” 18”

21 Inch 21” 22-

/16” 21” 24”

Face-Frame

Frameless

(a)

Excludes any items that might be placed in the

organizer.

(b)

Side Mounting requires the use of the included

Adapter Blocks. Cabinet construction varies; it

may be necessary to drill holes in your cabinet for

side mounting, or use additional spacers.

ITEM

QTY

1 Left, 1 Right

REQUIRED TOOLS (not included)

Drill

/16” Drill bit

Phillips Screwdriver

Tape Measure

Level

Pencil

DESCRIPTION

Lid Basket

Slides

Plastic Bracket

Slide Screw

Rack Screw

Hex Nut

Phillips Screw

Euro Screw

Adapter Block

IMPORTANT

READ ALL INSTRUCTIONS AND CHECK ALL PARTS BEFORE BEGINNING INSTALLATION

PARTS LIST

5 6 7 8 9

3 42

NOTE: Part #5 is small

and packed with Part #4

PART NUMBER

SS-20.1087 (LH), SS-20.1088 (RH)

SS-10.1028

SS-10.1029

SS-10.1030

SS-10.1031

SS-10.1032

SS-10.1033

SS-10.1034

DO NOT RETURN TO THE RETAILER

If you have any questions, please contact Customer Care at

1-800-721-4191

Monday – Friday 8-5 Central Time

4814113 - MEN0636 21” Soft Close Lid/Pan Organizer

4814114 - MEN0637 15” Soft Close Lid/Pan Organizer

Summary of content (8 pages)

PAGE 1
4814113 - MEN0636 21” Soft Close Lid/Pan Organizer 4814114 - MEN0637 15” Soft Close Lid/Pan Organizer DO NOT RETURN TO THE RETAILER If you have any questions, please contact Customer Care at 1-800-721-4191 Monday – Friday 8-5 Central Time PARTS LIST 1 2 5 3 6 4 7 8 9 NOTE: Part #5 is small and packed with Part #4 ITEM DESCRIPTION QTY PART NUMBER REQUIRED TOOLS (not included) 1 - 1 Left, 1 Right SS-20.1087 (LH), SS-20.1088 (RH) 1 Lid Basket Drill 2 Slides 3 Plastic Bracket 2 SS-10.
PAGE 2
Bottom Mount - START HERE STEP A1 Screw the Lid Basket to a left and right Slide using (4) Rack Screws. STEP A2 Place a Plastic Bracket on each Slide and place the assembly in the cabinet. NOTE: For a face-frame cabinet, make sure the Slides are located as to not strike the face-frame during operation. STEP A3 Using a pencil, mark two mounting holes in the front brackets of the Slides. Also mark the two holes in each Plastic Bracket. Remove the assembly from the cabinet.
PAGE 3
STEP A4 Drill 1/16” pilot holes in the marked locations. STEP A5 Attach the Plastic Brackets to the cabinet back wall using four Slide Screws. STEP A6 Insert the Slides into the Plastic Brackets and attach the assembly to the cabinet bottom using four Slide Screws.
PAGE 4
Side Mount (w/o Adapter Block) - START HERE STEP B1 Hold the left Slide against the inside of the cabinet face frame at desired height. Make a pencil mark at the top of the front bracket on the Slide. Use a tape measure and record the height from the bottom of the cabinet to this mark. NOTE: Take into consideration the sizes of items that will be placed in the Lid Basket and additional Lid Baskets or any other organizational products that may be installed.
PAGE 5
HO RIZ ON TA VERTICAL LINE Step B5 Remove the Slide and hold the Plastic Bracket on the cabinet back wall making sure to line up the top of Plastic Bracket with the horizontal line made in Step B1 and the center of Plastic Bracket holes placed on the vertical line. Mark the location of the two holes in the Plastic Bracket. LL VERTICAL LINE INE Step B6 Drill 1/16” pilot holes in the cabinet back wall and install the Plastic Bracket using (2) Slide Screws.
PAGE 6
Side Mount with Adapter Block - START HERE STEP C1 Prepare the Adapter Kit for use by inserting two Hex Nuts into the hex slots on one Adapter Block and threading a Phillips Screw into each Hex Nut. Repeat for the second Adapter Block. DO NOT fully tighten the Phillips Screws. Step C2 Hold the left Slide against the inside of the cabinet at the desired height. Locate the pre-drilled cabinet holes that are closest, vertically, to the center of the bracket on the Slide.
PAGE 7
Step C5 Temporarily install the left Slide onto the left Adapter Block using two Phillips Screws. Make sure to hold the Slide Level. Use a tape measure and record the height from the bottom of the cabinet to the top of the bracket on the front of the Slide. While holding the left Slide level and parallel to the inside wall, measure from the inside wall to the center of the front hole in the top of the Slide. LEVEL LEVEL Step C6 Remove the left Slide from the Adapter Block by removing the Phillips Screws.
PAGE 8
HO RIZ ON TA LL VERTICAL LINE INE Step C8 Drill 1/16” pilot holes in the cabinet back wall and install both Plastic Brackets using (4) Slide Screws. Step C8 Insert the Slides in the Plastic Brackets and attach each Slide to its Adapter Block using the Phillips Screws. Step C8 Install the Lid Basket onto the Slides using four Rack Screws. NOTE: If the Slides are not installed parallel, they may bind or be difficult to move during operation. Remove the Rack and check the operation of each Slide.