Installation Guide

ManualsBrandsAccess Lighting ManualsWall SconcesAccess Lighting Bermuda 11" Tall LED Outdoor Wall Sconce - 3000K

CERTIFICATION: cULus WET

NO. 20010LEDMG

INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

MESURES DE SECURITE A RESPECTURE

Before assembling your ACCESS LIGHTING fixture, please make sure that you

carefully read through this instruction sheet. Save this instruction sheet and

refer to it when additions to or changes in the fixture configuration are made

Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille

d'instructions et de s'y référer lorsque les ajouts ou changements dans la

configuration de montage sont faites.

CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH

CIRCUIT CONDUCTOR.

CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES

CONDUCTEURS DE LA DERIVATION SONT ADEQUATS

THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE

INSTALLATION CODE BY A PERSON FAMILIAR WITH THE

CONTSTRUCTION AND OPERATION OF THE PRODUCT AND THE

HAZARDS INVOLVED.

CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION

PERTINENT, PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET

SON FONCTIONNEMENT AINSI QUE LES RISQUES INHERENTS

NOTE: The important safeguards and instructions that appear in this manual

are not meant to cover all possible conditions and situations that may occur. It

must be understood that common sense, caution and care, are factors that

can’t be built into any product. These factors must be supplied by the person(s)

caring for and operating the fixture.

Read all instructions

Do not install this fixture in hazardous locations.

N'installez pas cet appareil dans des emplacements dangereux. Do

not install any fixture assembly closer than 6 inches from any curtain or

similar combustible material.

Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute surface

combustible.

"WARNING Risk of Fire and Electric Shock."

“CAUTION: Risque d’ Incendie et de Choc Electriques.”

COLLECTION

APPLICATION

MODEL NO.

BERMUDA

Wall Fixture

20010LEDMG

WHAT WE PROVIDE

WHAT YOU NEED

• Mounting Hardware

• Fixture Assembly

• Crossbar plate

• 1 x Frosted Glass shade

• LED Module

• Screwdriver

• Wire Cutters

• Wiring Supplies as Specified

by Electrical Code

GENERAL INFORMATION

STEP BY STEP INSTRUCTIONS

All electrical connections must be in accordance with all ordinances,

Local and the U.S. National Electrical Codes (NEC). These fixtures are

intended for mounting to a standard 4” metal octagon outlet box.

The box must be directly supported by the building structure and U.L.

recognized.

Before starting your installation disconnect the Power by turning off the

Circuit Breaker or by removing the fuse at the fuse box. Just turning the light

off at the light switch is not sufficient to prevent electrical shock.

Summary of content (2 pages)

PAGE 1
NO. 20010LEDMG CERTIFICATION: cULus WET INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS MESURES DE SECURITE A RESPECTURE Before assembling your ACCESS LIGHTING fixture, please make sure that you carefully read through this instruction sheet. Save this instruction sheet and refer to it when additions to or changes in the fixture configuration are made Lisez attentivement ce manuel d’instructions.
PAGE 2
NO. 20010LEDMG CERTIFICATION: cULus WET MOUNT CROSSBBAR AND MAKE WIRE CONNECTIONS 1 If there is an existing fixture remove it. Expose the supply wires from the J-box. Mount the crossbar to the J-Box with the supplied screws. Gently pull the supply wires through the hole in the crossbar plate. Connect the black supply wire to the black fixture wire. Secure with the supplied wire nuts. Connect the white supply wire to the white fixture wire. Secure with the supplied wire nuts.