AIRTAP SERIES REGISTER BOOSTER FAN SYSTEM USER MANUAL
WELCOME Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service. If you have any questions or suggestions, please don’t hesitate to contact us. Visit www. acinfinity.com and click contact for our contact information. EMAIL support@acinfinity.com WEB www.acinfinity.
MANUAL CODE AT2010X1 PRODUCT AIRTAP T4, Bronze 4” x 10” AIRTAP T4, White 4” x 10” AIRTAP T4, Bronze 4” x 12” AIRTAP T4, White 4” x 12” AIRTAP T6, Bronze 6” x 10” AIRTAP T6, White 6” x 10” AIRTAP T6, Bronze 6” x 12” AIRTAP T6, White 6” x 12” 4 MODEL AC-RBF4-B AC-RBF4-W AC-RBF42-B AC-RBF42-W AC-RBF6-B AC-RBF6-W AC-RBF62-B AC-RBF62-W UPC-A 819137020238 819137020245 819137020641 819137020658 819137020603 819137020610 819137020627 819137020634
MANUAL INDEX Manual Index ................................................................................. Page 5 Key Features ................................................................................. Page 6 Product Contents ........................................................................... Page 7 Installation .................................................................................... Page 8 Programming ..............................................................................
KEY FEATURES 6 ALUMINIUM FRAME Features an aluminum frame with CNC-machined corners and a white or bronze finish to give cabinets a clean look. SMART CONTROLLER Enables temperature monitoring, hot and cold temperature triggers, and fan speed control. DUAL BALL BEARINGS Enables unit to be mounted in any direction. Motor contains dual-ball bearings with a 67,000 hours lifespan. QUIET PWM MOTOR PWM-controlled motor features precise speed control, reduced noise, and energy-efficient DC power.
PRODUCT CONTENTS REGISTER FAN (x1) POWER ADAPTER (x1) SCREW SET (x2) 7
INSTALLATION STEP 1 Measure your register vent to make sure this model will fit. Standard sizes come in 4x10”, 4x12”, 6x10”, 6x12” etc. STEP 2 Remove your register grille. You may need to use a Philips screwdriver to remove the mounting screws.
INSTALLATION STEP 3 Plug the power adapter into an outlet. This can be next to your register or inside your register. STEP 3.5 If you are powering the register fan with an external outlet, run the power cord towards the groove on the side of the register fan.
INSTALLATION STEP 4 Plug the power adapter’s cord into the power receptacle of the register fan unit. STEP 5 Check the LCD display to see if it is lit and shows a number reading.
INSTALLATION STEP 6 Position the register fan to be mounted. If the outlet is external, make sure the cord runs through the gap between the wall and mounting plate. STEP 7 Drill your existing screws into the mounting holes to secure the register fan. If needed, use the screws included with your register fan. If the screw holes do not align, you may need to drill new holes into your wall.
PROGRAMMING 1. MODE BUTTON Cycles through the unit’s modes: temperature display, cooling trigger, heat trigger, and fan speed. 2. UP / DOWN BUTTON Changes the temperature setting in the cooling trigger, the heating trigger, and the fan speed. 3 1 4. COOLING TRIGGER Allows you to set a temperature trigger for the fans to run when your air conditioner system is on. 12 4 3. TEMPERATURE DISPLAY Displays the current temperature that is measured by the probe. Used as the default display. 6 5 2 5.
PROGRAMMING IMPORTANT NOTES – PLEASE READ This product is used to boost your existing AC or heater's airflow. It allows you to set temperature points where the fans will turn on if the airflow's temperature falls below or rises above the cooling or heating trigger's setting, respectively. This product has 10 fan speeds from 1-10. Use the fan speed setting to set your desired airflow boosting. Keep in mind the faster the fans spin, the louder they will be.
PROGRAMMING CONTROLLER LOCK To lock the controller, go to the temperature display mode and then hold the mode button for three or more seconds. While the display is locked, you will not be able to switch modes or adjust settings, but they will be working in the background. Holding the mode button for three or more seconds will unlock the controller. HIDE DISPLAY While the controller is locked, you can hide the display and turn off its backlight by pressing the mode button.
PROGRAMMING COOLING TRIGGER Use this mode to set the temperature trigger for your air conditioner. Please note you are NOT setting your desired temperature. In this mode, the fans will run if the probe temperature meets or falls below the trigger’s cold temperature setting. It will not run if the probe temperature is above the trigger’s cold temperature setting. Press the up or down buttons to set the cooling trigger temperature.
PROGRAMMING 1 2 Your air conditioner turns on. Cold air blows through the duct and into your room. 3 4 When the probe detects the airflow temperature has fallen below your Cooling Trigger, it will activate the fans. COOLING TRIGGER If the AC is turned off, the probe will detect a higher temperature than your Cooling Trigger, telling the fans to turn off. The fans will pull cold air from your duct to boost your AC output.
PROGRAMMING HEATING TRIGGER Use this mode to set the temperature trigger for your heater. Please note you are NOT setting your desired temperature. In this mode, the fans will run if the probe temperature meets or rises above the trigger’s hot temperature setting. It will not run if the probe temperature is below the trigger’s hot temperature setting. Press the up or down buttons to set the heating trigger temperature.
PROGRAMMING 1 2 Your central heating system turns on. Heated air blows through the duct and into your room. 3 4 When the probe detects the airflow temperature has risen above your Heating Trigger, it will activate the fans. HEATING TRIGGER If the heater is turned off, the probe will detect a lower temperature than your Heating Trigger, telling the fans to turn off. The fans will pull heated air from your duct to boost your heater output.
PROGRAMMING FAN SPEED This mode allows you to set a maximum fan speed in which they will actively run until you leave it. Pressing up or down will change the fan speed and determine the level of airflow boosting. Holding the MODE button will set the fan speed to 0. Keep in mind the faster the fans spin, the louder they will be. FAHRENHEIT OR CELSIUS To change the temperature scale between Fahrenheit and Celsius, hold the up and down buttons simultaneously until the letters change.
AIRTAP FAQ Q: Will I be able to mount this fan on my ceiling? A: For safety reasons, we do not recommend mounting the AIRTAP on your ceiling. Q: Will I be able to mount this fan on a baseboard style register? A: No. Because of the tilted design, the AIRTAP will not have the clearance to be properly mounted. Q: My register is bigger than my fan's rear insert. How can I fit this fan onto my register? A: We can only recommend using the appropriately sized AIRTAP fan for your register.
AC INFINITY PRODUCTS RACK FANS The CLOUDPLATE series rack fan system is designed for quietly cooling a wide range of audio, video, home theater, network, and IT equipments racks. The model features a thermal controller with intelligent programming that will automatically adjust the fan speeds in response to changing temperatures. DUCT FANS The CLOUDLINE series is a line of duct fans designed to quietly ventilate AV rooms and closets, as well as various DIY air circulation and exhaust projects.
WARRANTY This warranty program is our commitment to you, the product sold by AC Infinity will be free from defects in manufacturing for a period of two years from the date of purchase. If a product is found to have a defect in material or workmanship, we will take the appropriate actions defined in this warranty to resolve any issues. The warranty program applies to any order, purchase, receipt, or use of any products sold by AC Infinity or our authorized dealerships.
COPYRIGHT © 2021 AC INFINITY INC. ALL RIGHTS RESERVED No part of the materials including graphics or logos available in this booklet may be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form, in whole or in part, without specific permission from AC Infinity Inc.