ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH AU: 1800 029 701 N Z: 0800 466 444 admin@absco.com.au www.abscosheds.com.au Absco Industries Premier Shed Model: 23151GK FRONT: 2.26m SIDE: 1.52m HEIGHT: 1.95m 16 20 16 20 B ATBE SLA TCEONSCLRE RE CONC mm m 3100m mm m 2360m WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED EDGE 25mm DEEP AROUND THE PERIMETER For construction in non-cyclonic areas BOTTOM CHANNEL REBATED EDGE Wind rating: N2 as per AS4055-2012.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH GENERAL INSTRUCTIONS • Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. • Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST" pages. SITE PREPARATION • The site for the shed must be level. An uneven surface may result in misalignment of parts.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH COMPONENT PACKING LIST Check off all components. QTY COMPONENT DESCRIPTION PART CHECK QTY No. COMPONENT DESCRIPTION PART CHECK No.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH COMPONENT PACKING LIST QTY 1 1 1 2 2 1 2 1 4 1 COMPONENT DESCRIPTION A 55 CHANNEL L = 1496.5mm 55 C CHANNEL L = 1496.5mm B 55 CHANNEL L = 1496.5mm 60 A CHANNEL L = 1496.5mm A 81 CHANNEL L = 1496.5mm B 81 CHANNEL L = 1496.5mm A 58 CHANNEL WITH HINGES L = 1725mm B 58 CHANNEL L = 1725mm C 58 CHANNEL L = 773mm A CHANNEL L = 1568mm Absco Industries 79 PART CHECK QTY No.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH COMPONENT PACKING LIST COMPONENT DESCRIPTION QTY 2 1 1 PART No. CHECK QTY 89A Part No. Here JAMB L= 1785mm 89C Part No. Here JAMB L= 1725mm 4 4 COMPONENT DESCRIPTION PART No. CHECK 91A Part No. Here JAMB L= 1120mm 85A A 85 LIP TRIM L= 795mm 90A Part No. Here JAMB L= 1568mm INSTRUCTIONS & FITTINGS PACKET DOOR STRAP L: 165mm 2 2 8 CAP GABLE L: 170mm CHANNEL JOINER L= 200mm (7.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH SNAPTiTE ASSEMBLY GUIDE The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for tools and fasteners. To assemble each panel, the perimeter channels are secured to the top and bottom of each panel. Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet. Each perimeter channel must finish flush with the edges of the sheets.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH Guide on Joining Spliced Channels The text marked on all parts must be shown on the same side as each other = = = = CSJ = JOIN>> <> JOIN>> JO IN Step 2.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH PRE-ASSEMBLY OF SPLICED CHANNELS Join together 16 x channel sections using 8 x channel joiners (Part CSJ) NOTE: Some channels may have holes in them - You will need to redrill holes where CSJ joining channel covers them. m 3m ") (1 .
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH Guide on Joining a Spliced Ridge Beam Follow these three steps to assemble a ridge beam. ZARSP 225mm 50mm Step 1. Place two ridge beams as shown and push them together. Slide the cap of one under the other. Step 3. Turn over the ridge beam. Measure 250mm from the middle along the centre of one ridge beam, mark spacings of 50mm. Fasten with a Tek screw at each marking. NOTE.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH PRE-ASSEMBLY OF SPLICED RIDGE BEAM mm 16 AR 97 ZARSP m 5m 22 = 1x 97A L A 97 . mm 16 gth n ll le era m 3m 9 29 Ov . 1x 97AL 1x 97AR Absco Industries Assembly Instruction Manual Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH Absco Industries 81A 52A 52A 85A 14A 97A 52A 85A 52A 52A 81A OVERVIEW OF ROOF COMPONENTS 52A 52A 85A 52A 14A 60A 85A OVERVIEW OF ROOF COMPONENTS Assembly Instruction Manual Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH Absco Industries 89A 55C 89A 79A 91A 81E 34A 90A 82L 81B 81E 36L 30A 31A 36R 82R 31A 55B OVERVIEW OF WALL COMPONENTS 30A 91A 36R 82R 36L A 34A 15A 82L B 55A 22A OVERVIEW OF WALL COMPONENTS Assembly Instruction Manual Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH REAR PANEL ASSEMBLY 1x required. 30A 31A 31A 30A 55B SN E APT iT 81B E APT iT SN Absco Industries Assembly Instruction Manual Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH ROOF PANEL ASSEMBLY 2x required. 52A 52A 52A 52A D 60A 85A Fit 81A to edge of sheet with prepunched holes. D E APT iT SN 81A D D SN E APT iT 85A Absco Industries Assembly Instruction Manual Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH SIDE PANEL ASSEMBLY 2x required. 36R 36L Trim the tip of each sheet or bend out of the way to allow channels to fit hard up to the edge of the sheet. 15A 82R AP TE SN T i E P T iT A SN 82L E APT iT SN Absco Industries Assembly Instruction Manual Model: 30152GK 10/05/19 81E 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH 89A FRONT PANEL ASSEMBLY 1x required. 34A 89A 34A 55 A 55 A 89 89 A A 0A 9 90 A SN E APT iT 55A 90A E APT iT SN A 55 E APT iT SN 79A 55C E APT iT SN A 79 A 55 89 A C 55 A 79 55 Absco Industries Assembly Instruction Manual C Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH DOOR PANEL ASSEMBLY 58C 1x required. SNAPT iTE D 58C SNAPT iTE D 58A D 58B D D B 12A D D A D 58C SNAPT iTE 58A SNAPT iTE Vertical door channels are installed in the opposite orientation compared to the horizontal door channels. 89C 58C B A Long flange of channel Short flange of channel Four hole set for padbolt connection. Absco Industries Assembly Instruction Manual Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH DOOR PANEL ASSEMBLY 91A 91A B A Nuts and bolts may be used instead of pop rivets by drilling out hinge holes using a 4mm drill bit. Both are supplied. The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment, position each hasp centrally over the padbolt shaft and drill 3mm holes and secure with screws. Absco Industries Assembly Instruction Manual Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH PANEL CONSTRUCTION NOTE: Take care to ensure that all wall panels are not upside down. The top channels of each panel are pre-punched for attaching roof sheeting. The base channels are not prepunched. D D D D D D D D D D D D Orient panel so channel (60A) goes into ridge beam Side wall channels fit into the notched rear wall channels. D D 97A D D D Channel (81A) this end ide D D D D s his t l to .
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH INSIDE VIEW OF FIXING Secure peak brace to ridge beam and roof panel with one screw at each end Move the other roof panel into position and secure peak brace to ridge beam with one screw at each end Slide the roof panel into position and secure with one screw at each corner only at this stage. Absco Industries Assembly Instruction Manual Model: 30152GK 10/05/19 1.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH FINAL CONSTRUCTION 14A 360 360 250 250 250 250 600 600 600 600 ANCHORING OF SHED Location of 15 concrete anchors 250 360 360 250 250 250 Bend the top and bottom flanges as shown, then hook the bottom flanges under the top channel and screw top to the ridge beam with two screws. Each anchor consists of one nut, bolt, M10 dynabolt and steel angle. Drill a 10mm hole into the wall sheet. Drill a 10mm hole into the concrete.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH Absco Gable Roof Shed Notes General • 1.G This instruction manual shall be read in conjunction with other consultants drawings, specifications and written instructions provided by Absco and/or their representatives. • 2.G The drawings provided herein are for installation and structural engineering purposes only.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH Absco Gable Roof Shed Notes Steelwork • 1.S All structural steelwork shall have a corrosion protection system applied consistent with AS/NZS 23122002. • 2.S All structural steelwork detailed within this installation manual shall be minimum Grade • 550 for roll formed sections (including roof and wall sheeting) and Grade 250 for angle sections. • 3.S All roof, and wall sheeting shall be minimum base metal thickness of 0.3mm • 4.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH Australia Product Warranty Against Defects • Absco Sheds, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel. • We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 30 years from date of purchase, when installed within Australia.
ABSCO PREMIER SHED MODEL: 30152GK 3.00mW x 1.52mD x 1.95mH Absco Sheds Storage Guidelines • Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.
