802ZT Quick Start Guide ZTE CORPORATION ZTE Plaza, #55 Keji Road South, Hi-Tech, Industrial Park, Nanshan District,Guangdong,P.R.
Getting to Know Your Device Appearance 1 2 3 4 1. Power key 2. Screen 3. nano-SIM card tray 4.
5 8 5. Extended base 6. WAN/LAN switch 7. Charging/USB Type-C jack 8.
Getting to Know Your Device Connection Scenarios The device allows multiple clients to surf on the Internet at the same time. The following figure is for your reference only. LTE Mode: A nano-SIM card can be used to access the Internet. Extended Base: You can use this base to charge your device and connect to the Internet by connecting WAN to the WAN/LAN port.
Installing the Battery 1. Remove the back cover. 2. Install the battery. 3. Replace the back cover.
Installing the nano-SIM Card 1. Insert the tip of the tray eject tool into the hole. 2. Pull out the card tray and place the nano-SIM card on the tray. Carefully slide the tray back into place.
Connecting to Your Device Using Wi-Fi 1. Power on your device. 2. Ensure that your computer or other client devices have enabled Wi-Fi, and search for available wireless networks. NOTE: Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless networks. If you use a computer, you need to set your computer to obtain an IP address automatically. 3. Select the Wi-Fi name (SSID) of your device, and click Connect. 4. Enter the Wi-Fi password if necessary, and click OK.
Getting to Know the Wi-Fi SSID and Password You can view the label/Screen on the device to get the default Wi-Fi SSID and password.
Warning and Notice To the Users • If inadequately shielded, • • • • • • • • some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary. Operating the device may interfere with medical instruments such as hearing aids and pacemakers.
violate the related national regulations about telecom terminals. • Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected. • The device is not waterproof. Keep the device dry and store it in a shady and cool place. • Do not use the device immediately after a sudden temperature change, because dew may be generated inside and outside the device. Do not use it until it becomes dry.
Dispose of used batteries according to the instructions. Limited Warranty This warranty does not apply to defects or errors in the product caused by: i. ii. Reasonable abrasion. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual. v.
or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. LEGAL INFORMATION Copyright © 2018 ZTE CORPORATION. All rights reserved.
This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government: The exposure standard for wireless mobile devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
The highest SAR value for the device as reported to the FCC when tested for use at hotspot is 1.12W/kg and when worn on the body, as described in this user guide, is 1.09W/kg (Body-worn measurements differ among device models, depending upon available enhancements and FCC requirements.) While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement.
FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.
WCDMA Band 1,8 ,2,4 FDD LTE Band1,3,8,28,42;Band 2,4,12,17,41;Band 11 802.11 a/b/g/n/ac UNII-1:5150-5250MHz WCDMA Version Rel.10 LTE Version Rel.10 Maximum RF output power Tolerance Bands Max Power WCDMA B1 24.0 dBm+1dB/-3dB WCDMA B8 24.0 dBm+1dB/-3dB WCDMA B2 24.0 dBm+1dB/-3dB WCDMA B4 24.
LTE B1 23±2dBm LTE B3 23±2dBm LTE B8 23±2dBm LTE B28 23±2dBm LTE B42 23±2dBm LTE B2 23±2dBm LTE B4 23±2dBm LTE B12 23±2dBm LTE B17 23±2dBm LTE B41 23±2dBm LTE B11 23±2dBm 2.412-2.462GHz (FCC) ≤20dBm 2.412-2.
The guidelines use a unit of measurement known as Specific Absorption Rate, or SAR. The SAR limit for the devices is 2 W/kg and the highest SAR value for this device when tested at the body was 1.35W/kg* with 5 mm distance. As SAR is measured utilizing the device’s highest transmitting power, the actual SAR of this device while operating is typically below that indicated above.
The full text of the EU declaration of conformity is available at the following Internet address: http://certification.ztedevices.com Version No.: R1.0 Edition Time: November 14, 2018 Manual No.
