ZTE Grand X View2 Quick Start Guide (K81)
LEGAL INFORMATION Copyright © 2017 ZTE CORPORATION. All rights reserved. No part of this publication may be quoted, reproduced, translated or used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. Notice ZTE Corporation reserves the right to make modifications on print errors or update specifications in this guide without prior notice.
microSD Logo is a trademark of SD-3C, LLC. Qualcomm® Snapdragon™ processors are products of Qualcomm Technologies, Inc. Qualcomm and Snapdragon are trademarks of Qualcomm Incorporated, registered in the United States and other countries. Used with permission. Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories. Other trademarks and trade names are the property of their respective owners. Version No. : R1.
Getting to Know Your Device Speaker Front camera Indicator Touch Screen Home key Back key Recent apps key Speaker NOTE: The positions of the Back key and the Recent apps key are interchangeable through Settings > Navigation key.
Microphon e Headset jack Back camera Power button Volume buttons Card slot Micro-USB port 4
Installing the nano-SIM Card and microSD Card The nano-SIM card and the microSD card can be installed or removed while the device is turned on. You need to unmount the microSD card before removing it. WARNING! To avoid damage to the device, do not use any non-standard nano-SIM card cut from a SIM card. You can get a standard nano-SIM card from your service provider. 1. Insert your fingernail into the corner of the card slot cover and lift it up gently.
2. Hold the nano-SIM card/ microSD card with the cut corner oriented as shown and slide it into the card slot. Charging the Battery Your device's battery should have enough power for the device to turn on, find a signal, and make a few calls. You should fully charge the battery as soon as possible. WARNING! Use only ZTE-approved chargers and cables. The use of unapproved accessories could damage your device or cause the battery to explode. 1. Connect the adapter to the micro-USB port.
2. Connect the charger to a standard AC power outlet. 3. Disconnect the charger when the battery is fully charged. CAUTION: Do not change the built-in rechargeable battery in your device by yourself. The battery can only be changed by ZTE or ZTE authorized service provider. NOTE: If the battery is extremely low, you may be unable to power on the device even when it is being charged. In this case, try again after charging the device for at least 20 minutes.
For Your Safety General safety Don’t make or receive handheld calls while driving. Never text while driving. Don’t use at gas stations. Small parts may cause choking. Your device may produce a bright or flashing light. Your device can produce a loud sound. Don’t dispose of your device in fire. Avoid contact with anything magnetic. To prevent possible hearing damage, do not listen at high volume levels for long periods. Keep away from pacemakers and other electronic medical devices.
Turn off when near explosive materials or liquids. Only use approved accessories. Don’t rely on your device for emergency communications. Radio frequency (RF) energy This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States.
accordance with the measurement methods and procedures specified in IEEE1528. This device has been tested and meets the FCC and IC RF exposure guidelines when tested with the device directly contacted to the body. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.fcc.
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
d'Industrie Canada et a été testé en conformité avec les méthodes de mesure et procédures spécifiées dans IEEE 1528 et IEC 62209. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en conjonction avec tout autre antenne ou transmetteur.