602ZT Quick Start Guide ZTE CORPORATION NO. 55, Hi-tech Road South, Shenzhen, P.R.
LEGAL INFORMATION Copyright © 2017 ZTE CORPORATION. All rights reserved. No part of this publication may be quoted, reproduced, translated or used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. Notice ZTE Corporation reserves the right to make modifications on print errors or update specifications in this guide without prior notice. We offer self-service for our smart terminal device users.
Version No.: R1.
Getting to Know Your Phone Earpiece Front camera Front flash Indicator light Proximity & light sensor Volume key Power key Recent apps key Home key Back key Headset jack Back camera Back flash Back cover Speaker Charging/microUSB jack Microphone 4
Setting up Your Phone Power off your phone before removing or replacing the battery. Power off your phone before installing or removing the nano-SIM card. The microSDXC card can be installed or removed while the phone is turned on, but you need to unmount it before removing it. WARNING! To avoid damage to the phone, do not use any other kind of SIM cards, or any non-standard nano-SIM card cut from a SIM card. You can get a standard nano-SIM card from your service provider. 1.
Hold the microSDXC card with the cut corner oriented as shown and slip it into the card slot.
3. Insert the battery. Make sure the connectors on the battery go into the battery compartment first and align with the connectors in it. Gently push down on the battery until it clicks into place. 4. Install the back cover in the order and direction as shown in the figure.
Charging the Phone Your phone’s battery should have enough power for the phone to turn on, find a signal, and make a few calls. You should fully charge the battery as soon as possible. NOTE: If the battery is extremely low, you may be unable to power on the phone even when it is being charged. In this case, try again after charging the phone for at least 20 minutes. Contact the customer service if you still cannot power on the phone after prolonged charging.
Product Safety Information Don’t make or receive phone calls while driving. Never text while driving. The device could be used with a separation distance of 10 mm to the human body. Small parts may cause choking. Your phone can produce a loud sound. To prevent possible hearing damage, do not listen at high volume levels for long periods. Avoid contact with anything magnetic. Keep away from pacemakers and other electronic medical devices. Turn off when asked to in hospitals and medical facilities.
Specific Absorption Rate (SAR) Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health. The guidelines use a unit of measurement known as Specific Absorption Rate, or SAR. The SAR limit for mobile devices is 1.
CE Caution Battery Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. USB Port This product shall only be connected to a USB interface of version USB 2.0. Proper Use As described in this guide, your device can be used only in right location. If possible, please do not touch the antenna area on your device. Do not expose your device to extreme temperatures lower than – 10 °C and higher than + 55 °C.
Disposal of Your Old Appliance 1. When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2012/19/EU. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: 602ZT (FCC ID:SRQ-602ZT) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use close to human body is 0.852W/kg.
While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirements. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of http://www.fcc.