PROFESSIONAL SECURITY MADE EASY Security Camera Day/Night EN V1.
Introduction Congratulations on your purchase of This CCTV camera from ZOSI.This camera can operate in almost all lighting conditions, from bright daylight (provided it’s not pointed straight toward the sun) to pitch darkness. The camera is very sensitive to light and therefore can make use of even the smallest amount of light to provide an image of what it sees.In low light,this comes through as a black and white image.
Choosing a Location for this Camera To get optimal results from your camera, where you install is important. You should consider the distance between the camera and its subject to ensure you obtain a good view of the areas in focus. Also think about the appropriate mounting places (e.g., under the eaves of a roof is a good choice) where it won’t be either an easy target for vandals or affected by constant light reflections of moving vehicles (which can result in falsely triggered motion detection).
Mounting the Camera The camera can be mounted onto a flat, vertical surface using screws. The surface must have sufficient strength to hold the camera. Materials such as hardwood, brick or masonry are good options, You can mount the camera onto a metal surface, but you’ll need to supply your own mounting hardware. Positioning the Cables 1.When running your cable, try to avoid bending it at sharp angles. Please note, model shown is for illustration purposes only. 2.
Mounting the Camera Model 1 3 wrench 2 1 1 Rotate the camera by loosening the screw (using screw driver). 2 Adjust the elbow joint by loosening the screw. 3 The neck of the stand attached to the mounting base, rotate the stand by loosening the radial joint locking ring.Once in position , tighten the ring again.
Mounting the Camera Model 2 3 2 1 1 Rotate the camera by loosening the screw (using screw driver). 2 Adjust the elbow joint by loosening the screw. 3 The neck of the stand attached to the mounting base, rotate the stand by loosening the radial joint locking ring.Once in position , tighten the ring again.
Mounting the Camera Model 3 2 1 wrench 1 Adjust to the position you want up or down. 2 The neck of the stand attached to the mounting base, rotate the stand by loosening the radial joint locking ring. Once in position , tighten the ring again.
Mounting the Camera Model 4 3 8 2 1 1 loosen the screw on each side to adjust this joint ,this enables the camera left or right. 2 loosen the screw and adjust to the position you want (up or down). 3 loosen the screw on each side, to rotate the camera left or right.
Positioning the Cables Power Adapter Power Splitter Cable Video Connector 1 Video & Power Cable Please note, model shown is for illustration purposes only. Power Connector 1 2 For 2 & 4 camera packs: Connect the extension cable's DC socket to the multiple sockets on the power splitter.Then, plug the single end of the power splitter to the DC plug on the power adapter. 2 Power Adapter For a single camera: Connect the extension cable's DC socket to the DC plug on the power adapter.
Troubleshooting Q: Video Loss appears where the image from my camera should be displaying on my DVR? A: 1.Check the extension cable (power and video) is securely connected to the camera. 2.Check the video output from the camera is securely connected to a video input channel on the DVR. 3.Check the power from the camera is securely connected to a power supply.
Limited Warranty Terms & Conditions ZOSI Communications warrants this product against defects in workmanship and material for a period of one year from its original purchase date. You must present your receipt as proof of date of purchase for warranty validation. Any unit which proves defective during the stated period will be repaired without charge for parts or labour or replaced at the sole discretion of ZOSI.
PROFESSIONAL SECURITY MADE EASY www.zositech.com service@zositech.com All rights reserved. No part of this publication may be reproduced by any means without written permission from ZOSI. The information in this publication is believed to be accurate in all respects. ZOSI cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice.