ZOOM UNIVERSAL iHiFi TRANSMITTER and iHiFi STEREO HEADPHONES Quick Start English............................................... 3 Español.............................................
Using the Zoom® iHiFi™ Universal Transmitter and iHiFi Bluetooth® Stereo Headphones Your package includes: • • • • • iHiFi Universal Transmitter iHiFi Bluetooth Headphones USB cable for charging the headset and the transmitter Extender cable Velcro tabs for securing the transmitter to your iPod or MP3 player You will need: • A computer or USB hub with an available USB port for charging the Transmitter and Headphones using the included USB cable.
Step 1: Charging the Transmitter Charging LED On/Off (1/0) Switch Removable plastic jacket Mini-USB Connector a Make sure that your computer is NOT set to go into sleep mode after a period of inactivity. Check the computer's documentation for instructions. b Unless you have an iPod Mini, remove the plastic jacket from the Transmitter.
Step 2: Charging the Bluetooth Headphones Charging cable jack Charging cable On/Off (1/0) switch Charging LED Follow these steps: a Make sure that your computer is NOT set to go into sleep mode after a period of inactivity. Check the computer's documentation for instructions. b Plug one end of the supplied USB charging cable into the Headphones' charging jack. c With your computer turned on, plug the other end of the charging cable into an available USB port.
Step 3: Pairing the Universal Transmitter with the Headphones Pairing is the procedure that establishes a wireless link between two Bluetooth devices. To pair your music player with the Headphones: a Make sure the Headphones are within a few meters of your iPod or MP3 player. b Set your music player volume at a high level, about ¾ of maximum. (Later on you can control the volume with the Headphone controls.) c Plug the Universal Transmitter into the music player's stereo headphone jack.
Pairing LED Within 10 seconds, the Headphones and the Transmitter should pair. When they do, the Headphones' Pairing LED flashes blue for 10 seconds and then turns off. The Transmitter's blue LED continues to flash intermittently during the time it is paired with the Headphones. If the Transmitter loses pairing, its LEDs become steady on while it tries to re-initiate pairing. (If pairing doesn't occur, see the Notes on Pairing on page 11.
Using the Headphones to listen to your music player Volume Up ( ) Volume Down ( ) Phone Pairing LED Microphone As soon as the Universal Transmitter and the Headphones become paired, you can listen to the music stored on your music player. Use the and buttons on the Headphones to control the music volume. The chart on the next page lists button functions. The functions for making calls on your cell phone (see page 10) are shown in italics.
Button Answer/end phone call Pairing LED Microphone Function Lets you answer/terminate a phone call. In Idle state, hold down 2 seconds to redial the most-recently dialed number. Flashes red and blue while pairing, flashes blue when paired, and turns off after 10 seconds. Flips down for phone conversations. Mutes/unmutes the microphone. Play/ Pause Stop To power off the headphones, hold for 4 seconds. To power back on and re-initiate pairing, hold again for 4 seconds. Rejects an incoming call.
Caution from The American Speech-Language-Hearing Association (ASHA) To avoid hearing damage, ASHA counsels headphone users to turn down the volume, take frequent listening breaks, and wear headphones like Zoom's that fit over the ears to block background noise.
Note: Some phones also require you to tell them to connect to the paired device. That's all you need to do! You don't have to do anything on the Headphones. The Pairing LED on the Headphones will flash blue for 10 seconds, then turn off. Note: Please consult the phone's documentation if you need more information about pairing. When you hear the phone ring through the Headphones while you are listening to music, press the Phone button on the Headphones and flip down the microphone to answer the call.
If this happens, the Headphones go into Idle mode, and the Pairing LED flashes blue intermittently. If you come back in range within three minutes, the Headphones automatically become paired with the music player again. If you were simultaneously paired with your mobile/cell phone and your iPod/MP3 player, you may have to reinitiate pairing with the cell phone. If you don't come back within range within 3 minutes, the Headphones go into Sleep mode.
Both LEDs off Both LEDs steady on Red and blue LEDs alternating Blue LED flashing twice every three seconds Idle Searching for last paired device Pairing Paired and connected ► The Universal Transmitter can also work with your MP3-enabled phone, stereo system, TV, CD player, computer sound card, satellite radio, or any other audio device that has a stereo headphone/output jack.
We’ve included two strips of Velcro, one with 3 pieces of light gray Velcro and the other with 3 pieces of white Velcro. You use one of each color, and the extras will let you replace the Velcro if it starts to wear out. Velcro Pad Peel off one piece of gray Velcro and stick it on a clear, preferably flat area on the same side of your iPod/MP3 player as the headphone jack. Remember, the further from the jack the better, but it can’t be more than 3.75 cm (1.5 inches) from the jack.
If you choose to call a Zoom technician, the appropriate number depends on your country: US: (561) 997-9686 Portugal: +35 1221451012 Switzerland: +41 435000369 UK: 0870 720 0090 Spain: +34 911516304 Other (US number): (561) 997-9683 Some other Zoom iHiFi products Zoom’s Model 4355 iHiFi Transmitter for iPods plugs into the docking port of any iPod, and works with Zoom iHiFi Headphones and the Zoom iHiFi Receiver. Model 4360 iHiFi Receiver plugs into a stereo or powered speakers.
on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
O fabricante declara sob sua exclusiva responsabilidade que este equipamento está em conformidade com a Directiva 1999/5/EC através do seguinte. Este produto possui Marcação CE. El fabricante declara bajo su exclusiva responsabilidad que este equipo satisface la Directiva 1999/5/EC por medio de lo siguiente. Este producto tiene marca CE. Bu ürünün imalatçısı tüm sorumluluk kendisinde olmak kaydıyla bu cihazın aşağıdaki tabloda gösterilen biçimde 1999/5/EC (R&TTE Yönetmeliği) no.
Como Usar el Transmisor Universal Zoom® iHiFi™ y los Audífonos iHiFi Bluetooth® Estéreo Su paquete incluye: • • • • • Un Transmisor Universal iHiFi Audífonos iHiFi Bluetooth Cable USB para cargar el headset y el transmisor Cable de extensión Cinta velcro para asegurar el transmisor a su iPod o MP3 Usted necesita: • Un computador o USB hub con un puerto USB disponible para cargar el Transmisor y los Audífonos usando el cable USB aquí incluido.
Para usar los Audífonos, ver página 23. Para emparejar los Audífonos tanto con su reproductor de música como con su teléfono móvil/celular Bluetooth, ver página 25. Para ver algunos consejos sobre como usar el Transmisor, consulte la página 28. Paso 1: Como Cargar el Transmisor Luz LED para cargar Interruptor encender/apagar (1/0) Tapa plástica desprendible Conector Mini-USB a Asegúrese de que su computador NO este configurado para entrar en el modo inactivo después de un periodo de inactividad.
cargando y se vuelve tenue cuando ya ha finalizado el proceso de carga. d Cuando el Transmisor este completamente cargado, desconecte el cable de cargar del Transmisor y del PC. Un Transmisor completamente cargado funciona cerca de 6 horas. e Cuando el Transmisor no este en uso, cambie el interruptor 1/0 (Encender/apagar) a 0 (Apagar) para ahorrar la batería.
La luz LED para cargar de los Audífonos estará roja durante el proceso de carga. Puede que los Audífonos tomen hasta 2 horas para cargar por completo, momento en el cual la luz LED se volverá verde. d Cuando la luz LED este verde, desconecte el cable para cargar de los Audífonos y del computador. e Deje los Audífonos apagados hasta que este listo para emparejarlos con el Transmisor. Por lo general los audífonos completamente cargados funcionan por 12 horas.
Enchufe para Estereo Luces LED para Emparejamiento Botón Conectar El transmisor emparejará automáticamente con los Audífonos. Durante el proceso de emparejamiento las luces LED de emparejamiento del Transmisor titilarán en color rojo y azul. Las luces LED de emparejamiento de los Audífonos también titilarán en color rojo y azul. Luz LED para Emparejamiento En 10 segundos, los Audífonos y el Transmisor deberán emparejarse.
emparejamiento, sus luces LED quedarán fijas mientras él trata de reiniciar el emparejamiento. (Si el emparejamiento no ocurre, vea las Notas sobre Emparejamiento en la página 26.) Como Usar los Audífonos para Escuchar el Reproductor de Música Subir Volumen ( ) Bajar Volumen ( ) Teléfono LED de Emparejamiento Micrófono Tan pronto como el Transmisor Universal y los Audífonos se hayan emparejado, usted podrá escuchar la música guardada en su reproductor de música.
Botón Responder/term inar llamada telefónica LED para Emparejar Micrófono Función Le permite responder/terminar una llamada telefónica. En estado inactivo, sostenga por 2 segundos para marcar de nuevo el último número marcado. Titila en color rojo y azul durante el emparejamiento, titila en color azul cuando empareja y se apaga después de 10 segundos. Se voltea hacia abajo durante las conversaciones telefónicas. Cierra/abre el micrófono.
Advertencia de la Asociación Americana del HablaLenguaje-Audio (ASHA) Para evitar daño en la audición, ASHA aconseja a los usuarios de los audífonos bajar el volumen, tomar frecuentes descansos y usar audífonos como los de Zoom que se colocan sobre las orejas para bloquear el ruido de fondo.
f Cuando así se lo indique ingrese un código PIN de emparejamiento de 0000 y haga la conexión. Nota: Algunos teléfonos también requieren que se les indique que se conecten al dispositivo emparejado. Eso es todos lo que necesita hacer! No tiene que hacer nada con los Audífonos. La luz LED de emparejamiento en los Audífonos titilará en color azul durante 10 segundos y luego se apagará. Nota: Si necesita más información sobre el emparejamiento por favor consulte la documentación del teléfono.
con los que no desea emparejar. Retire estos dispositivos fuera de rango o apáguelos. • Los Audífonos pierden la conexión inalámbrica si están muy lejos de su iPod/MP3 o del teléfono celular – por ejemplo si usted se mueve fuera del rango de los 10 metros/30 pies sin quitarse los Audífonos. Si esto pasa los Audífonos entrarán al modo inactivo y la luz LED de Emparejamiento titilará intermitente en color azul.
Titileo intermitente color rojo Batería baja. Sin indicación Emparejado o en modo Inactivo, o los Audífonos están apagados o la batería esta muerta. Como Usar el Transmisor Universal Bluetooth ► Las dos luces LED superiores del transmisor le muestran el modo en que se encuentra.
► Con el Transmisor se han incluido algunas cintas de ® Velcro que puede usar para adherir el Transmisor a su iPod u otro dispositivo de audio. El Velcro funciona mejor si esta lo más lejos posible del enchufe de los audífonos del reproductor de música, pero ninguna parte del Velcro puede estar a más de 3.75 cm (1.5 pulgadas) del enchufe o no alineará correctamente con el Transmisor.
pegajoso) contra el Velcro gris que ya instalo de manera que las dos piezas se unan. Luego conecte el Transmisor, teniendo cuidado de que este derecho. Presiónelo en su lugar de manera que empuje contra el lado pegajoso del Velcro blanco. Cuando haga esto por primera vez debe dejar el Transmisor en su lugar por lo menos una hora antes de sacar el Transmisor y el dispositivo de audio aparte. Para mayor seguridad, le recomendamos que los deje unidos hasta el día siguiente.
Algunos otros productos iHiFi Zoom El Transmisor iHiFi Modelo 4355 de Zoom para iPods conecta en el puerto de cualquier iPod y funciona con los Audífonos y el Receptor iHiFi de Zoom. El Receptor iHiFi Modelo 4360 conecta con parlantes estéreo o eléctricos. Recibe inalámbricamente y toca el audio desde un iPod, MP3, computador, u otro dispositivo que tenga capacidad Bluetooth A2DP.
3487-C 27456-2 ©2007