User Manual

ManualsBrandsZoom Telephonics ManualsElectronicsSensor

ZoomGuard

Starter Package Documentation

Chapter 1. Overview

ZoomGuard lets you protect, monitor, and control a home, office, or other site.

This package includes:

* Internet Link Model XX and its power cube and Ethernet cable.

* Wireless Multi-sensor M Model XX and its optional mounting bracket

* 1,000 mAH battery for Multi-Sensor M

* Magnet for Multi-Sensor M that’s used to monitor a door, window, or drawer opening

and/or closing

* Tape for optional use in mounting

A ZoomGuard system always includes the following:

1) At least one ZoomGuard Internet Link. A

ZoomGuard Internet Link communicates

wirelessly with up to 12 nearby ZoomGuard sensor

and/or controls, linking those sensor/controls

through the Internet and a Zoom Internet-

connected Server to smartphones, computers,

phones and other devices you choose. The

ZoomGuard Internet Link Model 8005 connects to

a router that’s linked to the Internet, so you need a router or modem/router. The Multi-

sensor M Model 8105 in this Starter Package is one of the 12 sensor/controls that can

connect to the Internet Link. You can add additional multi-sensors and other ZoomGuard

sensor/controls to your system now or in the future.

2) One or more Sensors and Controls. The Zoom Multi-sensor M can sense water

leaks, temperature, light, motion, door/window/drawer openings and closings, or a button

push. The Zoom Multi-sensor H is similar, but replaces the motion sensor with a

humidity sensor. The Zoom Power Sensor/Control can monitor power usage at an outlet

and also temperature and light; and can allow you to power on or off a connected heater,

air conditioner, light, or other device locally or from a distance over the Internet. Zoom

has a long list of planned wireless sensors and controls, including a Smoke Detector

Companion, Indoor/Outdoor Alarm, Thermostat, and Lightswitch. ZoomGuard Monitors

and Controls always connect wirelessly to a ZoomGuard Internet Link, with typically up

to 12 Monitors and Controls connected to one Internet Link. More than one Internet Link

can be used in an installation with more than 12 Monitors and Controls or one that spans

a greater distance than one ZoomGuard Internet Link can reach. ZoomGuard software

allows you to setup and control as many Internet Links and sensor/controls as you like,

even ones spread all over your city or country!

Summary of content (8 pages)

PAGE 1
ZoomGuardtm Starter Package Documentation Chapter 1. Overview ZoomGuard lets you protect, monitor, and control a home, office, or other site. This package includes: * Internet Link Model XX and its power cube and Ethernet cable.
PAGE 2
3) The Internet. This transmits Sensor information from a ZoomGuard Internet Link through a Zoom Server to Remote ZoomGuard Devices, and also transmits Control information from ZoomGuard Sensors and Remote ZoomGuard Devices through a Zoom Server to a ZoomGuard Internet Link and connected ZoomGuard Controls.
PAGE 3
Chapter 2. Connecting ZoomGuard Internet Link Model 8005 To A Router ZoomGuard Internet Link Model 8005 connects to the Ethernet port of almost any router or broadband modem/router. Just do the following: 1) Connect the Internet Link’s Power Cube between a power outlet and the power jack of the Internet Link. 2) Flip up the antenna on the top of the Internet Link, since that antenna position normally gives you better wireless connection to ZoomGuard sensor/controls.
PAGE 4
Chapter 3: Connecting and using a Multi-sensor M Model 8105 First you need to decide where to put the multi-sensor. This depends on what you want to do with it. Please keep in mind that you can use anywhere from one to all of the multisensor’s sensors if you’d like. The only sensors that have a noticeable effect on battery life are the motion sensor, the open/close detector, and the flood sensors; and ZoomGuard setup software lets you turn each of these on or off.
PAGE 5
sensor. (Discuss this further and show a drawing. Ideally we’d determine an angle up and down for the cone.) The angle of view is much smaller vertically, to allow you to place the multi-sensor high enough that it doesn’t detect pets. ZoomGuard software has a Calibration function that blinks a light on the Multisensor so you can see when it detects motion.
PAGE 6
Once the battery is installed, it helps to bring the multi-sensor within 30 feet or so of its Internet Link. This helps the multi-sensor and Internet Link to establish a wireless connection, which you can tell by seeing a rapidly blinking green light when the connection is first established. Then you can bring the multi-sensor much farther away, sometimes over 100 feet, and it will continue to work.
PAGE 7
Chapter 4: Using ZoomGuard Web Software ZoomGuard Web software is easy and self-documented. We recommend doing setup using a computer or tablet, since they have a larger screen than a phone. However, you can use a phone if you like as long as it has a Web browser. To use ZoomGuard Web software, go to www.XXX and follow the easy instructions.
PAGE 8
Appendix A: Compliance Information FCC Statement: This equipment has been tested and fount to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable Protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.