Bellatrix, Inc.
FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Information to the User This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of FCC Rules.
Quick Installation Model: Reference Card FM-SFT56i COBRA 56x With Voice Mail Speakerphone | PCI Dual Mode IT-T V.90 & Flexible SFT Win Modem i 2 sitars Upgrade 1 BI 56,000" bps Data Modem (DUAL MODE) supporting both V.90 and Flexible | BI 14,400 bps Send & Receive Fax ¥ Supports speeds up to 115,200 bps & Full Featured Voice Messaging Ml Speakerphone Functions 1 V.42 Error Correction and V.42bis 4-to-1 Data Compression Actual speeds vary depending upon fine conditions.
Installing your fax/modem if you have never installed an add-in board in your computer before, please follow the instructions in this section carefully. You may also wan to refer to the Installation Chapter in your manual Safety Precautions 1. Tum OFF the computer before you begin. Also, turn OFF any external devices that are connected to your computer, such ag printers. 2. Handle the board gently by the edges.
Jumper settings Before inserting the modem into the soot in the computer, you should go over the following options to properly configure the modems jumper settings.
Connecting to a sound card (via Sound cards line-in} To control the volume of the modem use your sound cards software audio mixer or the Wing volume control and use the Line selection. 1. Connect an audio cable, with a 1/8 inch stereo plug at both ends, into the modems speaker jack. 2. Connect thee other end of the audio cable into the sound cards line-in jack. Inserting the Fax/Modem 1. Tun off the power to the computer. Also, turn off any external devices that are attached, such as a printer and monster.
Installing Telephone Lines (See Fig. 2} The Fax/Modem has two modular telephone jacks on the back of the made. You will need to connect your Fax/Modem to the wall outlet vig a modular telephone cord, If your Walt outlet is not a modular type, you can purchase an inexpensive converter at most electronics or phone stores. It is suggested that you connect your modem to a “dedicated ling’. A dedicated line is a regular phone line that does not go through a switchboard, PBX, etc...
Testing The actual installation of the modem is now complete. Before attempting to use your modem, you should complete the following steps: 1. Before turning the power back on to the computer, check the telephone connection by lifting the telephone handset. You should hear a dial tone. i you don’, check that all phone cords are firmly connected. If you still don't hear a dial tone, refer to Appendix A (Troubles heating) in the installation manual. 2. Tum the computer power back on.
Windows 95(0SR2) Driver Installation 1. Start Windows 95. As soon as Windows 95 stars you will seg a screen similar to the diagram to the right: 2. Click on the button, You will see a screen similar to the diagram to the right: 4. Click on the Other Locations button 10 bring up a screen similar to the diagram to the right: §. Click on the Browse button and then select the correct drive and directory containing the Wing driver and then click on the OK button.
6. Click on the [Eas] 0 button to complete the modem driver installation. it the screen to the right is displayed, Click on Browse and once again select the correct drive and directory that contains, the modem driver to complete the driver installation, 7. You should then see the Modem driver and Wave device for the voice modem detected and installed. Windows 98 Driver Installation 1. Start Windows 98. As soon as Windows 98 starts you will see a screen similar to the diagram to the right: 2.
button. if you have the Bellatrix COMMUNICATIONS CD-ROM, insert the CD-ROM into your CD-ROM drive and select DAFMSFTS6I Note: Replace D: with the drive letter of your CD-ROM drive if necessary. button will be grayed out until you find a directory that actually contains a modem driver. 5. Click on the button. If the directory contained the driver you will see a screen scimitar to the diagram to the right: 6. Dickson the bunion, You will see a screen similar to the diagram to the right: 8.
UN-Instailation of the Windows 85/98 Driver If you ever want to remove the modem or update the modem drivers with newer versions obtained on the web, you must first remove the HSF modem drivers. We provided a utility program that not only removes the modem driver, but completely removes all the modem entries in the Windows registry. Use the following procedure to remove the modem drivers. 1. Start the Control Panel and double click on You should see a screen similar to the diagram to the right: 2.
Common Problems and Their Solutions Problem:Modem answers incoming calls and then returns {0 the on-hook condition, disconnecting the caller. This scours most often when connecting to a UNIX system. In most case, the host does riot prefer to see any result or command echo codes. If this is the sacs, the codes can be disabled by adding EQ QF to the modem configuration string. Problem:No echo from modem This is normally caused by an JO address or IRQ conflict.
Feature Notes In addition te high speed fax and data waster functions, your demimonde supports the following additional voice features: personal Vole Messaging System Automatically detect and route incoming voice, fax and data calls. Create up 10 899 voice mailboxes, each with a personal mailbox greeting message. Listen to voice messages through the telephone handset or speakers. Record your own greeting messages for each mailbox. Monitor incoming calls and answer the calls at your own convenience.