User's Manual

Congratulations on the purchase of your smart doorlight!
This quick start guide will assist you on getting the doorlight
up and running as soon as possible. We recommend that
you connect everything and give it a try before you do a
permanent installation, to make sure nothing was damaged
during shipping.
For the hardware of the doorlight:
Connects with the
external socket
USB Connector for the
PIR cable
HD Camera, press up and
down for vertical direction
adjust
Horizontal direction
adjust for camera
Introduction
Getting to Know Your Smart doorlight:
1
2
For the PIR cable:
Before you begin, you need to know:
For indoor use, please install it at dry locations.
For outdoor use, please install it under a weatherproof
cover.This doorlight can be mounted either base up or
down.Make sure the doorlight is within range of your
WiFi connection.
Disconnect the power
supply before you install
the doorlight.
Plug the doorlight into
your existing socket.
PIR sensor
MIC
Speaker
Infrared LEDs
3
Doorlight Installation:
1
3
2
4
1
2
3
4
Now you can power on the doorlight. It will switch
the seven basic colors for one time and then lights
in white color. To set up the camera and control the
color theme fo the doorlight, you need to set it up
with the mobile app.
Plug in the included PIR cable to the doorlight,
and attach the other side to the wall with the
adhesive tape.
Mobile setup
4
TM ®
Connect your Android phone or iPhone to the
WiFi network that you want your camera to use.
Make sure that you know the password to connect
to this network.
You can also view your device on any computer
using MeShare’s free web app. Simply use your MeShare
username and password and log in to
user.meshare.com.
System Requirements: Android™ (v.4.0 or newer) or
® ® ®
iPhone , iPad , iPod touch (v.7.0 or newer) ,a
password-protected 2.4GHz WiFi network.
Download and install the ‘MeShare’ app from
TM TM
Google Play or the App Store . Launch the app
and sign up for a free MeShare account.
MeShare
Log in and press the Add Device option
located on the bottom of the screen. Follow the
on-screen instructions to complete your setup!
MeShare App Interface
5
Tap one point on one photo
among the nine themes to
select the favorite color
theme.
9
View captured alarm
snapshots.
Enter the camera's
live view.
My MeShare Interface
Access colors and themes
settings.
Invite your family or friends
to view the clips of
moments.
To customize six of your
favorite color, first tap one
of the six pads here.
5
Select one color on the
color wheel.
6
Drag the color bar to
adjust the color
saturation.
7
Three modes of the button:
Grey to turn off the light
Green to turn on the light
Auto will turn on or off the
light according to the light
changes.
8
Color Control Interface
5
6
8
7
9
We have partnered with MeShare to bring you
optional cloud services! The MeShare Cloud
Service (MCS) allows you to:
Visit for more www.meshare.com/cloud
information on plans and features.
MeShare Web App
Now compatible with MeShare!
Create and save video clips from your
recordings.
Access your playback footage and clips from
any location with Internet connection.
Share recorded footage and clips with family
and friends.
Access more smart features in the future!
Record continuously and store the footage on
our secure cloud servers.
Viewing Options
6
9
Having difficulty?
For more instructions, troubleshooting, support
information, our knowledge base, the community
forum, and other resources, please visit:
http://www.zmodo.com/supports
Like us on Facebook.com
/Zmodo
Scan the QR-code below!
Follow us on Twitter
@Zmodo
Scan the QR-code below!
Android is a trademark of Google Inc. Google Play is a trademark
of Google Inc. Apple, the Apple Logo, and iPhone are trademarks
of Apple Inc., registered in the U.S. and other countries. App
Store is a service mark of Apple Inc.
Connect with us!
8
Important Information
9
Support
7
Smart LED DoorLight
with Video Camera
QUICK
START
GUIDE
ON
ON
FCC Verification
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
IC ID Verification (for Canana)
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
For lamps with a weight significantly higher than that of the
lamps for which they are a replacement, attention should be
drawn to the fact that the increased weight may reduce the
mechanical stability of certain luminaires and lampholders and
may impair contact making and lamp retention.”
Warning -Changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment must be installed and operated in accordance
with provided instructions and the antenna(s) used for this
transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for
satisfying RF exposure compliance.