Installation Manual RANGE TOPS www.zlinekitchen.
ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams is never out of reach. Through our unique designs and unparalleled quality, we’re dedicated to providing you an elevated experience in the heart of your home. With an endless selection of features and finishes, our inspiration is your reality.
ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury designs and professional features into everyone’s homes. Because we continually strive to improve our products, we may change specifications and designs without prior notice. Scan the QR code to view the most up-to-date version of the Installation Manual and User Manual. WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ��������������������������������������1 BEFORE INSTALLATION ��������������������������������������������������������������4 Technical Product Dimensions �������������������������������������������������������������������������������� 4 Cabinet Cutout Dimensions ����������������������������������������������������������������������������������� 5 Securing The Range Top ����������������������������������������������������������������������������������������� 7
IMPORTANT SAFETY INSTRUCTIONS GAS SAFETY WARNING: If the information in these WARNING instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. • Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. • WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch. • Do not use any phone in your building.
IMPORTANT SAFETY INSTRUCTIONS If the information in this manual is not followed exactly, a fire or explosion WARNING may result causing property damage, personal injury, or death. • Before beginning installation, please read and follow these important instructions for the safety of your home and the people living in it. • The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation, improper use of the appliance, or failure to heed the warnings listed.
IMPORTANT SAFETY INSTRUCTIONS An air curtain or other overhead range/range top hood, which operates WARNING by blowing downward airflow onto the range, shall not be used/installed in conjunction with this gas range top. • Please ensure that the altitude of your home is conducive for the use of gas cooking products. If the product is installed at higher altitudes above sea level, you may experience issues with gas pressure that will affect product performance.
m) BEFORE INSTALLATION TECHNICAL PRODUCT DIMENSIONS 29 3/4" ) (756 mm 27 1/2" (699 mm) 24" (610 mm) 7 7/8" (200 mm) 27 1/2" (699 mm) (70) 22"3/4 3/4" (70 mm) 35 3/4" ) (908 mm 7 7/8" (200 mm) 27 1/2" (699 mm) 11"3/8 3/8" (35) (35 mm) 1 1"5/1 5/16 7 7/8" (200 mm) ) (1219 mm 47 3/4" 5 3/8" (137 mm) 27 1/2" 7 7/8" (200 mm) 1"15/15 2" (51 mm)(48.5) (699 mm) REAR RECESS GRATE HEIGHT 27 1/2" (699 mm) 24" (610 mm) (70) 22"3/4 3/4" (70 mm) mm) 1 1"5/16 5/16" (33 (33.
BEFORE INSTALLATION CABINET CUTOUT DIMENSIONS 13" (330 mm) max 6" (152 A mm) 18" (457 mm) 30"‒36" (762‒914 mm) uct width W1: Prod ut width W2: Cuto Cutout depth: 24" (610 mm) Cutout height: 7 7/8" (200 mm) Cutout Dimensions 36" (914 mm) 5 SIZE RT30 series models W1 29 3/4" (756 mm) W2 30" (762 mm) RT36 series models 35 3/4" (908 mm) 36" (914 mm) RT48 series models 47 3/4" (1213 mm) 48" (1219 mm)
BEFORE INSTALLATION OTHER INSTALLATION REQUIREMENTS AND NOTES • The dimensions shown on page 5 represent minimum clearance to combustible surfaces; no combustible materials are to be located within these areas. • For cutout depth of 24" (610 mm) noted on page 5, the recommendation for all RT models is the standard cabinet depth of 24" (610 mm) so the front face of the range top sticks out from the counter for optimal access.
BEFORE INSTALLATION SECURING THE RANGE TOP While the range top is stable enough to sit on top of a 3/4" (20mm) or thicker platform itself while pushed flush against the wall, ZLINE recommends the following options to secure the appliance and prevent tipping: MOUNTING TO CABINET SHELF Secure appropriate-sized screws or bolts to the cabinet shelf and slide them into the keyhole slots (see Figure 1 for location) as the range top is pushed into place.
BEFORE INSTALLATION GAS SUPPLY • This appliance shall only be installed by an authorized professional. • If local codes permit, a flexible metal appliance connection with the new AGA or CGA certified design, 3/4" (19 mm), is recommended for connecting this appliance to the gas supply line. DO NOT bend or damage the flexible connector when moving the appliance. • This appliance must be used with the pressure regulator provided (see below).
BEFORE INSTALLATION ROOM VENTILATION An exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the appropriate national and local standards. Exhaust hood operation may affect other vented appliances; in each case it shall be installed in conformity with the appropriate national and local standards. TYPE OF GAS This appliance is shipped from the factory for use with natural gas.
INSTALLATION • For gas inlet position of appliance refer to Figures 1 and 2. After installing the gas supply and making all connections check thoroughly for possible leaks. Turn all control knobs on the unit to ‘OFF’ position. • Open the valve on the gas supply. Using a soap and water solution check each gas connection one at a time by brushing the solution over the connection. Presence of bubbles will indicate a leak. • Tighten the fitting and re-check for leaks.
INSTALLATION To check inlet pressure of the appliance: • Disconnect electric power before checking pressure. • Take off one of the gas burner caps and the relative flame spreader in order to get access to the burner injector. • Place the pressure detector directly on the burner injector, then afterward open the relative burner knob at maximum position keeping it pressed, then measure the outlet pressure from the burner injector.
INSTALLATION GAS CONNECTION • All gas connections must comply with national and local codes. The gas supply line (service) must be the same size or greater than the inlet line of the appliance. This range top uses a 1/2" NPT inlet. Use appropriate sealant on all pipe joints that are resistant to gas. • This range top can be used with natural or liquid propane gas. The range top is shipped from the factory for use with natural gas.
INSTALLATION ELECTRIC POWER RATING A properly grounded and horizontally-mounted electrical NEMA 5-15 receptacle should be installed no higher than 3" (76 mm) above the floor, and no less than 2" (51 mm) and not more than 8" (203 mm) from the left side (facing product). The appliance shall be connected to a single phase electric line rated at 120VAC and 60HZ. The true voltage in most homes is usually within this rating.
INSTALLATION MANUAL SHUT-OFF VALVE • This valve is not shipped with the appliance and must be provided by the installer. • The valve must be installed in the gas service line between the gas hook-up on the wall and the appliance inlet, in a position where it can be reached quickly in the event of an emergency. • In Massachusetts: A T-handle type manual gas shut-off valve must be installed in the gas supply line to this appliance.
INSTALLATION PRESSURE REGULATOR Since service pressure may fluctuate with local demand, every gas cooking appliance must be equipped with a pressure regulator on the incoming service line for safe and efficient operation. Pressure Regulator • The pressure regulator shipped with the appliance has two female 1/2" (13 mm) NPT threads. • The regulator shall be installed properly in order to be accessible when the appliance is installed in its final position.
INSTALLATION LIQUID PROPANE CONVERSION PROCEDURE The gas conversion procedure for this range top includes: 1. Pressure Regulator 2. Surface Burners 3. Flame Adjustment The conversion is not finished if all steps are not completed. Before performing the gas conversion, locate the package containing the replacement orifices, which has a number indicating its flow diameter printed on the body. Consult the table below for matching orifices to burners.
INSTALLATION Reference the diagrams below if your range was manufactured before May 2021. To check, reference the rating label under the range top.
INSTALLATION Reference the diagrams below if your range was manufactured after May 2021. To check, reference the rating label under the range top.
INSTALLATION STEP 1: PRESSURE REGULATOR The pressure regulator supplied with the appliance is a convertible type pressure regulator for use with natural gas at a nominal outlet pressure of 4" W.C.P. (1 kPa) or liquid propane gas at a nominal outlet pressure of 10" W.C.P. (2.5 kPa) and it is pre-assembled from the factory to operate with one of these gas pressures as indicated in the labels affixed on the appliance, package, and instruction booklet.
INSTALLATION STEP 2: SURFACE BURNERS To replace the orifices of the surface burners, lift up the burners and unscrew the orifices shipped with the range top using a 7 mm socket wrench. Replace orifices using the conversion set supplied with the range top. Each orifice has a number indicating its flow diameter printed on the body. Consult the images starting on page 16 for matching orifices to burners.
INSTALLATION STEP 3: FLAME ADJUSTMENT 1. Light one burner at a time and set it to the MINIMUM position (small flame). 2. Remove the knob by firmly and carefully pulling it straight out. 3. The range is equipped with a safety valve. Using the 2.0 x 50 mm flat-head screwdriver provided with this manual, locate the adjustment screw (see diagram below), hold the metal stem with one hand and turn the screwdriver to the right or left until the burner flame is adjusted to desired minimum. 4.
INSTALLATION INSTALLATION CHECKLIST 1. Is the back guard of the range top securely connected? If not, locate screws to secure. 2. Is the electricity properly grounded to a dedicated NEMA 5-15 receptacle? 3. Is the gas service line connected following the directions of the manufacturer? 4. Have all the proper valves, stoppers, and gaskets been installed between the range top and the service line? 5. Has the gas connection been checked for leaks? 6.
WARRANTY COVERAGE ZLINE Kitchen and Bath (“ZLINE”) range tops have a one year parts and service warranty and a limited lifetime warranty on burners, which includes parts and labor for spark tips. ZLINE warranty periods begin from the original purchase date of the product and solely cover the original purchaser of the product, delivered new and in its original carton.
WARRANTY If a product qualifies within the service window provided under these warranty terms, and ZLINE is unable to repair the product or a defective part of the product after a reasonable number of attempts, ZLINE reserves the right to offer to replace the defective part or the product or provide the original purchaser a full refund of the purchase price of the product (not including installation, removal, or other charges that were not included in the original purchase price).
WARRANTY In the event service is dispatched, and it is discovered that the reported issue is not covered under warranty based on the disclaimers above, the customer will be responsible for all service fees. Failure to pay these fees will result in the forfeiture of remaining warranty coverage.
WARRANTY SERVICE For warranty service, please contact our Customer Service team at 1-614-777-5004 or visit www.zlinekitchen.com/contact to utilize our online Customer Experience Portal. Scan the QR code to view the most up-to-date version of our Installation Manual and User Manual. Need to purchase a part or accessory for your ZLINE product? Visit www.zlineparts.com, ZLINE’s official parts distribution partner.
4.0.1 1-614-777-5004 www.zlinekitchen.com contact@zlinekitchen.