Quick Start Guide FaceDepot - 7BL Version: 1.
Overview Flash Microphone Camera Network interface Connection interface 7 inch touch screen Magnetic tamper switch Speaker Alarm AUX GND SEN GND BUT NO COM NC ALAL+ Lock Auxiliary input Power GND +12V Reset Sensor Exit Button Connection interface FP & RFID Reader (Optional) Fingerprint sensor Card reading area 1 +12V GND Wiegand INWD0 In INWD1 Wiegand W D 0 Out WD1 RS232 RS232 RS485 12V GND 485A 485B TXD1 RXD1 GND TXD2 RXD2 USB port
Device Installation Method 1: Installation on the wall 2 1 3 1.5m ① Attach the mounting template sticker to the wall, and drill holes according to the mounting paper. Fix the back plate on the wall using wall mounting screws. ② Attach the device to the back plate. ③ Fasten the device to the back plate with a security screw. Note: If you want to install FP & RFID reader, please insert the reader after step ①. Method 2: Install on the barrier gate Adjust the device 1. Adjust the angle of the device. 2.
Standalone Installation Smoke detector Alarm Door Sensor Exit Button Lock Card Reader TCP/IP ZKBioSecurity Note: On this document, we just guide you to connect some normal components, if you want more connection of SRB, external fingerprint reader and so on, please check user manual document.
Lock Relay Connection The system supports Normally Opened Lock and Normally Closed Lock. The NO LOCK (normally opened at power on) is connected with 'NO' and 'COM' terminals, and the NC LOCK (normally closed at power on) is connected with 'NC' and 'COM' terminals.
Barrier Connection AUX GND SEN GND BUT NO K1 COM GND Barrier gate NC ALAL+ Ethernet Connection 1 2 3 4 5 6 7 8 RJ 45 Default IP address: 192.168.1.201 Subnet mask: 255.255.255.0 ZKBioSecurity IP address: 192.168.1.130 Subnet mask: 255.255.255.0 Click [COMM.] > [Ethernet] > [IP Address], input the IP address and click [OK]. Note: In LAN, IP addresses of the server (PC) and the device must be in the same network segment when connecting to ZKBioSecurity software.
Power Connection GND 12V DC Recommended power supply 1) 12V ± 10%, at least 3000mA. 2) To share the power with other devices, use a power supply with higher current ratings. User Registration When there is no super administrator set in the device, click on to enter the menu. After setting the super administrator, the system will request for the administrator’s verification before entering the menu.
L L L Method2: Register on ZKBioSecurity software Please set the IP address and cloud service server address on the device. 1. Click [Access] > [Access Device] > [Device] > [Search Device] to add the device to the software. When the device has set the server address and port, it can be added automatically.
Step 1 Step 2 Step 3 Step 4 2. Click [Personnel] > [Person] > [New] to register users in the software. 3. Add users to access levels. 4. Click [Access] > [Device] > [Device Control] > [Synchronize All Data to Devices]. For more details, please refer to the ZKBioSecurity User Manual. Method3: Register on the phone Once ZKBioSecurity software installation, users could enroll face via browser application on their own mobile phone. 1.
2. The users will display in [Personnel] > [Temporary Personnel], click [Review]. Ethernet and Cloud Server Settings Click on > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface. Click on > [COMM.] > [Cloud Server Setting] to set the server address and server port, that is, the IP address and port number of the server after the software is installed.
L Access Control Settings Click on > [Access Control] to enter the access control management interface and set relevant parameters of access control.
ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town, Longgang District, Shenzhen China 518129 Tel: +86 755-89602345 Fax: +86 755-89602394 www.zkteco.com Copyright©2019 ZKTECO CO., LTD. All rights reserved.
