‘Thermal Infrared temperature. measurement module Flash Camera & Palm collector Microphone « 5" touchscreen Fingerprint sensor Magnetic tamper Wen = switch Speaker Reset feo] [mo] ma | he ald Note: Not all products have the function with =, the real product shall prevail. Please refer to the following recommendations for installation.
( Attach the mounting template sticker to the wall, and drill holes according to the mounting paper. Fix the back plate on the wall using wall mounting screws, @ Attach the device to the back plate, @ Fasten the device to the back plate with a security screw.
The system supports Normally Opened Lack and Normally Closed Lock.
1) 12V = 10%, at least 3000mA. 2) Ta share the power with other devices, use a power supply with higher current ratings. readiness: 192.168.1130 Default IP address; 192.168.1.201 Subset mask 2552552550 Subset mask. 255.255.2550 Click [COMM] > [Ethernet] > [IP Address], Input the IP address and click [OK]. Note: In LAN, IP addresses of the server (PC} and the device must be in the same network segment when connecting to Accessorizes MTD software.
‘When there is no super administrator set in the device, click on to enter the menu. After setting the super administrator, the system will request for the administrator's verification before entering the menu. For the security purpose, It is recommended to register a super administrator at the first time you use the device. Method 1: Register on the device Click oni: > [User Mgt] > [New User] to register a new user.
Method 2: Register on Accessible MTD software Please set the IP address and cloud service server address on the device. 1. Click [Access] > [Access Device] > [Device] > [Search Device] to add the device to the software. When the device has set the server address and port, it can be added automatically. 2.Click [Personnel] > [Person] > [New] to register users in the software. 3. Add users to access levels. 4, Click [Access] > [Device] > [Device Control] > [Synchronize All Data to Devices].
Method 3: Register on the phone Once Accessible MTD software Installed, users could enroll face via browser application an their own mobile phone. 1. Click [Personnel] > [Parameters], input *timeserver sportiness the QR Code UGL bar. The software will automatically generates a QR code. Scan the QR code or login onto *timeserver by the mobile phone to register users.
Click on iz: > [COMM] > [Ethernet] to set the network parameters. If the TC PAP communication of the device Is successful, the con 2 will be displayed In the upper right comer of the standby interface. Click on > [COMM] > [Cloud Server Setting] to set the server address and server port, that is, the IP address and port number of the server after the software is installed. If the device communicates with the server successfully, the Icon & will be displayed in the upper right comer of the standby interface.
Click on 3 > [Attendance Search] > [Attendance Record] to enter the records query Interface, input the user ID and select the time range, the corresponding attendance logs will be displayed,
Click on i=: > [System] > [Detection Management] to enter the setting interface. 1. You can set the value of High temperature alarm threshold. The device will send an alarm prompt when the temperature of the user detected exceeds this value. 2.When the Temperature over the range; access denied is enabled, the user will be forbidden to access, as shown in the following figure. 3.
1. The effective distance for temperature detection is within 50cm. 2. Recommended for indoor use. 3. Temperature measurement data is for reference only, not for medical use. 4, Remove the mask to register the face, wear a mask to recognize the face, the type of mask, the size of the face covered by the mask, and bangs will affect the facial recognition effect. 5. Facial verification for masked individuals will increase FAR. Palm verification for masked individuals is recommended.
1. Place your palm within 30-50cm of the device, 2. Place your palm In the palm collection area, such that the palm Is placed parallel to the device. 3. Make sure to keep space between your fingers. This device complies with part 15 of the FCC Rules Operation is subject tithe following two conditions: {1) This device may not cause harmful Interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
the users encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver, Connect the equipment inch an outlet ona circuit different from that to which the receivers connected. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.