Product Name and Model Number User Manual User Manual RevFace15[TI] Date: July 2021 Doc Version: 2.0 English Thank you for choosing our product. Please read the instructions carefully before operation. Follow these instructions to ensure that the product is functioning properly. The images shown in this manual are for illustrative purposes only. For further details, please visit our Company’s website www.zkteco.com. P a g e |1 Copyright©2020 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual Copyright © 2021 ZKTECO CO., LTD. All rights reserved. Without the prior written consent of ZKTeco, no portion of this manual can be copied or forwarded in any way or form. All parts of this manual belong to ZKTeco and its subsidiaries (hereinafter the "Company" or "ZKTeco"). Trademark is a registered trademark of ZKTeco. Other trademarks involved in this manual are owned by their respective owners.
RevFace15[TI] User Manual relating to the use of the information contained in or referenced by this manual, even if ZKTeco has been advised of the possibility of such damages. This manual and the information contained therein may include technical, other inaccuracies or typographical errors. ZKTeco periodically changes the information herein which will be incorporated into new additions/amendments to the manual.
RevFace15[TI] User Manual About the Company ZKTeco is one of the world’s largest manufacturer of RFID and Biometric (Fingerprint, Facial, Finger-vein) readers. Product offerings include Access Control readers and panels, Near & Far-range Facial Recognition Cameras, Elevator/floor access controllers, Turnstiles, License Plate Recognition (LPR) gate controllers and Consumer products including battery-operated fingerprint and face-reader Door Locks.
RevFace15[TI] User Manual Document Conventions Conventions used in this manual are listed below: GUI Conventions For Software Convention Bold font > Description Used to identify software interface names e.g., OK, Confirm, Cancel. Multi-level menus are separated by these brackets. For example, File > Create > Folder. For Device Convention Description <> Button or key names for devices. For example, press . [] Window names, menu items, data table, and field names are inside square brackets.
RevFace15[TI] User Manual Table of Contents 1 SAFETY MEASURES ......................................................................................................................... 7 2 OVERVIEW...................................................................................................................................... 10 3 INSTRUCTION FOR USE ................................................................................................................. 11 3.
RevFace15[TI] User Manual 8.3 FACE PARAMETERS ...............................................................................................................................................................................50 8.4 DETECTION MANAGEMENT .................................................................................................................................................................54 8.5 DEVICE TYPE SETTING .........................................................................
RevFace15[TI] 1 User Manual Safety Measures The below instructions intend to ensure that the user can use the product correctly to avoid danger or property loss. The following precautions are to keep users safe and prevent any damage. Please read carefully before installation. Noncompliance with instructions could lead to product damage or physical injury (may even cause death). 1.
RevFace15[TI] User Manual 10. Lightning - Can install external lightning conductors to protect against electrical storms. It stops power-ups from destroying the system. Recommended installing the devices in areas with limited access. Electrical Safety Before connecting an external cable to the device, complete grounding properly, and set up surge protection; otherwise, static electricity will damage the mainboard.
RevFace15[TI] User Manual Note Make sure whether the positive polarity and negative polarity of the DC 12V AC adapter is connected correctly. A reverse connection may damage the device. It is not advisable to connect the AC 24V AC adapter to the DC 12V input port. Make sure to connect the wires following the positive polarity and negative polarity shown on the device's nameplate.
RevFace15[TI] 2 User Manual Overview RevFace15[TI] uses Thermal Imaging Intelligent Engineering Facial Recognition algorithms and the latest Computer Vision Technology. It supports facial verification with large capacity and quick recognition and also improves security performance in all aspects. It accepts touchless recognition technology and new functions namely Temperature Detection and Masked Individual Identification which eliminates hygiene concerns effectively.
RevFace15[TI] 3 User Manual Instruction for Use Before getting into the device features and functions, it is recommended to be familiar with the below fundamentals. 3.1 Standing Position, Posture and Facial Expression The recommended distance The distance between the device and a user whose height is in a range of 1.55m-1.85m is recommended to be 0.3-2.5m. Users may slightly move forward or backward to improve the character of facial images captured.
RevFace15[TI] User Manual 3.2 Face Registration Try to keep the face in the centre of the screen during registration. Please face towards the camera and stay still during face registration. The screen should look like this: Correct face registration and authentication method Recommendation for registering a face When registering a face, maintain a distance of 40cm to 80cm between the device and the face. Be careful to keep your facial expression natural and not to change.
RevFace15[TI] User Manual Recommendation for authenticating a face Ensure that the face appears inside the guideline displayed on the screen of the device. Sometimes, authentication may fail due to the change in the wearing glasses then the one used while registration. In such a case, you may require authenticating your face with the previously worn glasses. If your face was registered without glasses, you should authenticate your face without glasses further.
RevFace15[TI] User Manual 3.4 Virtual Keyboard NOTES: The device supports the input in Chinese language, English language, numbers, and symbols. • Tap [En] to switch to the English keyboard. • Press [123] to switch to the numeric and symbolic keyboard. • Tap [ABC] to return to the alphabetic keyboard. • Tap the input box, a virtual keyboard appears. • Tap [ESC] to exit the virtual keyboard. P a g e | 14 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 3.5 Verification Mode 3.5.1 Facial Verification 1:N Facial Verification 1. Conventional verification In this verification mode, the device compares the collected facial images with all face data registered in the device. The following is the pop-up prompt of a successful comparison result. 2.
RevFace15[TI] User Manual 3. Enable mask detection When the user enables the Enable mask detection function, the device identifies whether the user is wearing a mask while verification or not. The following are the popups of the comparison result prompt interface. P a g e | 16 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 4. Display Thermodynamics Figure When the user enables the Display Thermodynamics Figure function, the thermal image of the person is displayed in the upper left corner of the device, while verification. As shown in the images below: 1:1 Facial Verification In this verification mode, the device compares the face captured by the camera with the facial template related to the entered user ID.
RevFace15[TI] User Manual If the user has registered password in addition to the face, and the verification method is set to Password/ Face verification, the following screen will appear. Select the icon to enter the face verification mode. P a g e | 18 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual After successful verification, the prompt box displays "Successfully verified", as shown below: If the verification is failed, it prompts "Please adjust your position! ". 3.5.2 Multi-face Verification 1:N Multi-face Verification 1. Conventional verification In this verification mode, the device compares the collected multi-person facial images with all the face data registered in it. The device supports verification of up to 4 people at once.
RevFace15[TI] User Manual 2. Enable temperature screening with infrared When Enable temperature screening with infrared function is on, the user's body temperature is measured before the verification process begins. During the user verification process, the user's face must be aligned with the temperature measurement area to measure the body temperature. It displays the measured temperature either in value or in the normal/abnormal temperature range.
RevFace15[TI] User Manual Turn on body temperature display Turn off body temperature display 3. Enable mask detection When the user enables the Enable mask detection function, the device identifies whether the user is wearing a mask while verification or not. The following are the popups of the comparison result prompt interface. Turn on body temperature display NOTE: Not wearing a mask is displayed as P a g e | 21 Turn off body temperature display icon. Copyright©2021 ZKTECO CO., LTD.
RevFace15[TI] User Manual 4. Display Thermodynamics Figure When the user enables the Display Thermodynamics Figure function, the thermal image of the person is displayed in the upper left corner of the device, while verification. As shown in the images below: Turn on body temperature display Turn off body temperature display 1:1 Multi-face Verification In this verification mode, the device compares the face captured by the camera with the facial template associated to the entered user ID.
RevFace15[TI] User Manual If the user has a registered password in addition to the face, and the verification method is set to Password/ Face verification, the following screen will appear. Select the icon to enter the face verification mode. After the verification is successful, the prompt box will display the verification result, as shown in the figure below: P a g e | 23 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 3.5.3 Password Verification The device compares the entered password with the registered password of the given User ID. Tap the button on the main screen to enter the 1:1 password verification mode. Then, input the user ID and press [OK]. P a g e | 24 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual If the user has registered face in addition to a password, and the verification method is set to Password/ Face verification, the following screen will appear. Select the icon to enter password verification mode. Input the password and press [OK]. Following are the display screen after entering a correct password and a wrong password respectively. P a g e | 25 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual Verification is successful P a g e | 26 Verification is failed Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] 4 User Manual Main Menu on the Standby interface to enter the Main Menu, the following screen will be displayed: Press Function Description Menu Descriptions User Mgt. To Add, Edit, View, and Delete information of a User. User Role To set the permission scope of the custom role and enroller for the users, that is, the rights to operate the system. COMM. To set the relevant parameters of Network, Serial Comm.
RevFace15[TI] 5 User Manual User Management 5.1 User Registration Tap User Mgt. on the main menu. 5.1.1 User ID and Name Tap New User and enter the User ID and Name. NOTES: 1) A name can take up to 17 characters. 2) The user ID may contain 1-9 digits by default. 3) You can modify your ID during the initial registration but not after registration. 4) If a message "Duplicated!" pops up, you must choose another ID as the entered User ID already exists. P a g e | 28 Copyright©2021 ZKTECO CO.
RevFace15[TI] User Manual 5.1.2 User Role On the New User interface, tap on User Role to set the user’s duty as either Normal User or Super Admin. • Super Admin: The Super Administrator owns all management privileges in the Device. • Normal User: If the Super Admin is registered already in the device, then the Normal Users will not have the privilege to manage the system and can only access authentication verifications.
RevFace15[TI] User Manual 5.1.4 Password Tap Password in the New User interface to enter the password registration page. • On the Password interface, enter the required password and re-enter to confirm it and tap OK. • If the re-entered password is different from the initially entered password, then the device prompts the message as "Password not match!", where the user needs to re-confirm the password again. NOTE: The password may contain 1 to 8 digits by default.
RevFace15[TI] User Manual 5.1.5 Profile Photo Tap on Profile Photo in the New User interface to go to the Profile Photo registration page. • When a user registered with a photo authenticates successfully, the user's registered photo is displayed. • Tap Profile Photo to open the device’s camera, then tap the camera icon to take a photo. The captured photo is displayed on the top left corner of the screen and the camera opens up again to take another photo, after taking the initial photo.
RevFace15[TI] User Manual 5.2 Search User On the Main Menu, tap User Mgt., and then tap All Users to search a User. • On the All Users interface, tap on the search bar on the user’s list to enter the required retrieval keyword (where the keyword may be the user ID, surname, or full name) and the system will search for the related user information. P a g e | 32 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 5.3 Edit User On the All Users interface, tap on the required user from the list and tap Edit to edit the user information. NOTE: The process of editing the user information is the same as adding a new user, except that the User ID cannot be modified when editing a user. The process in detail refers to "5.1 User Registration". 5.
RevFace15[TI] User Manual 5.5 Display Style On the Main Menu, tap User Mgt., and then tap Display Style to enter Display Style setting interface. All the Display Styles are shown as below: Single Line P a g e | 34 Multiple Line Mixed Line Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] 6 User Manual User Role User Role facilitates assigning some specific permissions to certain users based on the requirement. • On the Main menu, tap User Role > User Defined Role to set the user-defined permissions. • You may set the permission scope of the custom role (up to 3 roles) and an enroller, that is, the permission scope of the operation menu. • On the User Defined Role interface, toggle Enable Defined Role to enable or disable the userdefined role.
RevFace15[TI] User Manual NOTE: If the User Role is enabled for the device, tap on User Mgt. > New User > User Role to assign the created roles to the required users. But if there is no super administrator registered in the device, then the device will prompt "Please enroll super admin first! " when enabling the User Role function. P a g e | 36 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] 7 User Manual Communication Settings Communication Settings are used to set the parameters of the Network, Serial Comm, PC connection, Wireless Network, Cloud server, and Wiegand, Network Diagnosis. Tap COMM. on the main menu. 7.1 Network Settings When the device needs to communicate with a PC over the Ethernet, you need to configure network settings and ensure that the device and the PC connect to the same network segment. Tap Ethernet on the Comm.
RevFace15[TI] User Manual Function Description Function Name Descriptions IP Address The default IP address is 192.168.1.201. It can be modified according to the network availability. Subnet Mask The default Subnet Mask is 255.255.255.0. It can be modified according to the network availability. Gateway The default Gateway address is 0.0.0.0. It can be modified according to the network availability. DNS The default DNS address is 0.0.0.0. It can be modified according to the network availability.
RevFace15[TI] User Manual Master Unit: When RS485 is used as the function of "Master unit", it can be connected to a card reader. There are 4 baud rate options at which the data communicates with PC. They are: 115200 (default), 57600, 38400, and 19200. Baud Rate The higher is the baud rate, the faster is the communication speed, but also the less reliable.
RevFace15[TI] User Manual Tap Wireless Network on the Comm. Settings interface to configure the Wi-Fi settings. Searching the Wi-Fi Network • WIFI is enabled in the device by default. Toggle the • Once the Wi-Fi is turned on, the device will search for the available Wi-Fi within the network range. • Tap on the required Wi-Fi name from the available list and input the correct password in the button to enable or disable WIFI. password interface, and then tap Connect to WIFI (OK).
RevFace15[TI] User Manual Adding WIFI Network Manually The WIFI can also be added manually if the required WIFI does not show on the list. Tap on Add WIFI Network to add the WIFI manually. On this interface, enter the WIFI network parameters. (The added network must exist.) NOTE: After successfully adding the WIFI manually, follow the same process to search for the added WIFI name. Click here to view the process to search the WIFI network.
RevFace15[TI] User Manual 7.5 Cloud Server Setting Tap Cloud Server Setting on the Comm. Settings interface to connect with the ADMS server. Function Description Function Name Enable Domain Name Disable Domain Name Description Server Address Once this mode is turned ON, the domain name mode "http://... " will be used, such as http://www.XYZ.com, while "XYZ" denotes the domain name. Server Address The IP address of the ADMS server. Server Port Port used by the ADMS server.
RevFace15[TI] User Manual 7.6.1 Wiegand input Function Description Function Name Descriptions Wiegand Format Its value can be 26 bits, 34 bits, 36 bits, 37 bits, and 50 bits. Wiegand Bits The number of bits of the Wiegand data. Pulse Width(us) The value of the pulse width sent by Wiegand is 100 microseconds by default, which can be adjusted within the range of 20 to 100 microseconds.
RevFace15[TI] User Manual ECCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCO Wiegand34 It consists of 34 bits of binary code. The 1st bit is the even parity bit of the 2nd to 17th bits, while the 34th bit is the odd parity bit of the 18th to 33rd bits. The 2nd to 25th bits is the card numbers. ESSSSSSSSCCCCCCCCCCCCCCCCCCCCCCCCO Wiegand34a It consists of 34 bits of binary code. The 1st bit is the even parity bit of the 2nd to 17th bits, while the 34th bit is the odd parity bit of the 18th to 33rd bits.
RevFace15[TI] User Manual 7.6.2 Wiegand output Function Description Function Name Descriptions SRB When SRB is enabled, the lock is controlled by the SRB to prevent the lock from opening due to device removal. Wiegand Format Its value can be 26 bits, 34 bits, 36 bits, 37 bits, and 50 bits. Wiegand output bits After selecting the required Wiegand format, select the corresponding output bit digits of the Wiegand format.
RevFace15[TI] User Manual 7.7 Network Diagnosis It helps to set the network diagnosis parameters. Tap Network Diagnosis on the Comm. Settings interface. Enter the IP address that needs to be diagnosed and tap Start the diagnostic test to check whether the network can connect to the device. P a g e | 46 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] 8 User Manual System Settings It helps to set related system parameters to optimize the accessibility of the device. Tap System on the Main Menu interface to get into its menu options. 8.1 Date and Time Tap Date Time on the System interface to set the date and time. • Tap Manual Date and Time to manually set date and time and tap Confirm to save. • Tap Select Time Zone to select a time zone then tap the return button to save and exit.
RevFace15[TI] User Manual Week Mode • Date Mode When restoring the factory settings, the time (24-hour) and date format (YYYY-MM-DD) can be restored, but the device date and time cannot be restored. NOTE: For example, if a user sets the time of the device (18:35 on March 15, 2020) to 18:30 on January 1, 2021. After restoring the factory settings, the time of the device will remain at 18:30 on January 1, 2021. 8.2 Access Logs Setting Tap Access Logs Setting on the System interface.
RevFace15[TI] User Manual Function Description Function Name Description Choose whether to capture and save the current snapshot image during verification. There are 5 modes: No Photo: No photo is taken during user verification. Take photo, no save: Photo is taken but not saved during verification. Camera Mode Take photo and save: All the photos taken during verification is saved. Save on successful verification: Photo is taken and saved for each successful verification.
RevFace15[TI] User Manual 8.3 Face Parameters Tap Face on the System interface to go to the face parameter settings. FRR FAR High Recommended Matching Thresholds 1:N 1:1 Low 85 80 Medium Medium 82 75 Low High 80 70 P a g e | 50 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual Function Description Function Name Description 2D Monocular Anti-Spoofing: It detects the spoof attempt using visible light images to determine if the provided biometric source sample is of a real person (a live human being) or a false representation. 2D Monocular Anti-Spoofing Threshold: It facilitates judging whether the captured visible image is a real person (a live human being). The larger the value, the better the anti-spoofing performance using visible light.
RevFace15[TI] User Manual Face Enrollment Threshold: During face enrollment, 1:N comparison is used to determine whether the user has already registered before. When the similarity between the acquired facial image and all registered facial templates is greater than the set threshold, it indicates that the face has already been registered. Face Pitch Angle: It is the pitch angle tolerance of a face for facial template registration and comparison.
RevFace15[TI] User Manual Tracking Identification: The same face can only be recognized once. To recognize it again, you must leave the face recognition area and re-enter it before it can be recognized again. Face Comparison Interval(s): After the interval identifying is clicked (selected), for example, if the comparison interval is set to 5 seconds, then the face recognition will verify the face every 5 seconds. Valid value: 0 to 9 seconds.
RevFace15[TI] User Manual 8.4 Detection Management Tap Detection Management on the System interface to configure the Detection Management settings. Function Description Function Name Description It enables or disables the infrared temperature measurement. Enable temp. screening with infrared When this function is enabled, users must pass the temperature screening in addition to identity verification before the access to be granted.
RevFace15[TI] User Manual Enable capture of unregistered person To enable or disable the capture of unregistered person function. When enabled, the device will automatically capture the photo of the unregistered person, enabling this feature requires to enable Allow unregistered people to access. Temperature deviation correction As the temperature measurement module reads a small range of variation of an observed value under unusual environments (humidity, extreme room temperature, etc.).
RevFace15[TI] User Manual Function Description Function Name Description Time Attendance Terminal Set the device as a time attendance terminal. Access Control Terminal Set the device as an access control terminal. NOTE: After changing the device type, the device will delete all data and restart, and some functions will be adjusted accordingly. 8.
RevFace15[TI] 9 User Manual Personalize Settings Tap Personalize on the Main Menu interface to customize interface settings, voice, bell, punch state options, and shortcut key mappings. 9.1 Interface Settings Tap User Interface on the Personalize interface to customize the display style of the main interface. Function Description Function Name Description Wallpaper It helps to select the main screen wallpaper according to the user preference.
RevFace15[TI] Menu Screen Timeout (s) User Manual When there is no operation, and the time exceeds the set value, the device automatically goes back to the initial interface. The function can either be disabled or set the required value between 60 and 99999 seconds. Idle Time To Slide Show (s) When there is no operation, and the time exceeds the set value, a slide show is displayed. The function can be disabled, or you may set the value between 3 and 999 seconds.
RevFace15[TI] User Manual New Bell Schedule Tap New Bell Schedule on the Bell Schedule interface to add a new bell schedule. Function Description Function Name Description Bell Status Toggle to enable or disable the bell status. Bell Time Once the required time is set, the device automatically triggers to ring the bell during that time. Repeat Set the required number of counts to repeat the scheduled bell. Ring Tone Select a ringtone.
RevFace15[TI] User Manual 9.4 Punch States Options Tap Punch States Options on the Personalize interface to configure the punch state settings. Function Description Function Name Description Off: Disable the punch state function. Therefore, the punch state key set under Shortcut Key Mappings menu will become invalid. Manual Mode: Switch the punch state key manually, and the punch state key will disappear after Punch State Timeout.
RevFace15[TI] • User Manual On the Shortcut Key Mappings interface, tap on the required shortcut key to configure the shortcut key settings. • On the Shortcut Key (that is "F1") interface, tap function to set the functional process of the shortcut key either as punch state key or function key. • If the Shortcut key is defined as a function key (such as New user, All users, etc.), the configuration is completed as shown in the image below.
RevFace15[TI] • User Manual Once the Switch cycle is selected, set the switch time for each day and tap OK to confirm, as shown in the image below. NOTE: When the function is set to Undefined, the device will not enable the punch state key. P a g e | 62 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 10 Data Management On the Main Menu, tap Data Mgt. to delete the relevant data in the device. 10.1 Delete Data Tap Delete Data on the Data Mgt. interface to delete the required data. Function Description Function Name Description Delete Access Records To delete attendance data/access records conditionally. Delete Attendance Photo To delete attendance photos of designated personnel. Delete Blocklist Photo To delete the photos taken during failed verifications.
RevFace15[TI] User Manual Delete Profile Photo To delete all user photos on the device. Delete Wallpaper To delete all wallpapers in the device. Delete Screen Savers To delete the screen savers in the device. The user may select Delete All or Delete by Time Range when deleting the access records, attendance photos or block listed photos. Selecting Delete by Time Range, you need to set a specific time range to delete all data within a specific period. Select Delete by Time Range.
RevFace15[TI] User Manual 11 Access Control On the Main Menu, tap Access Control to set the schedule of the door opening, locks control and to configure other parameters settings related to access control. To gain access, the registered user must meet the following conditions: • The relevant door’s current unlock time should be within any valid time zone of the user’s time period.
RevFace15[TI] User Manual 11.1 Access Control Options Tap Access Control Options on the Access Control interface to set the parameters of the control lock of the terminal and related equipment. Function Description Function Name Description It toggles between ON or OFF switch to get into gate control mode or not. Gate Control Mode Door Lock Delay (s) When set to ON, the interface removes the Door lock relay, Door sensor relay, and Door sensor type options.
RevFace15[TI] User Manual Door Available Time Period It sets the timing for the door so that the door is accessible only during that period. Normal Open time Period It is the scheduled time-period for “Normal Open” mode so that the door is always open during this period. Master Device While configuring the master and slave devices, you may set the state of the master as Out or In. Out: A record of verification on the master device is a check-out record.
RevFace15[TI] User Manual On the selected Time Zone number interface, tap on the required day (that is Monday, Tuesday, etc.) to set the time. Specify the start and the end time, and then tap OK. P a g e | 68 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual NOTES: 1) The door is inaccessible for the whole day when the End Time occurs before the Start Time (such as 23:57~23:56). 2) It is the time interval for valid access when the End Time occurs after the Start Time (such as 08:00~23:59). 3) The door is accessible for the whole day when the End Time occurs after the Start Time (such that Start Time is 00:00 and End Time is 23:59). 4) The default Time Zone 1 indicates that the door is open all day long. 11.
RevFace15[TI] User Manual Delete a Holiday On the Holidays interface, select a holiday item to be deleted and tap Delete. Press OK to confirm the deletion. After deletion, this holiday does not display on the All Holidays interface. 11.4 Combined Verification Access groups are arranged into different door-unlocking combinations to achieve multiple verifications and strengthen security.
RevFace15[TI] User Manual • If the Door-unlock combination 3 is set as (09 09 09 09 09). It indicates that there are 5 people in this combination; all of which are from AC Group 9. • If the Door-unlock combination 4 is set as (03 05 08 00 00). It indicates that the unlock combination 4 consists of only three people. The first person is from AC Group 3, the second person is from AC Group 5, and the third person is from AC Group 8.
RevFace15[TI] User Manual Function Description Function Name Description No Anti-Passback: The Anti-Passback function is disabled, which means successful verification through either the master device or slave device can unlock the door. The attendance state is not saved in this option. Anti-Passback direction Out Anti-Passback: The user can check-out only if the last record is a check-in record otherwise an alarm is raised. However, the user can check-in freely.
RevFace15[TI] User Manual 12 Attendance Search Once the identity of a user is verified, the access record is saved in the device. This function enables users to check their event logs. Select Attendance Search on the Main Menu interface to search for the required event logs. The process of searching for attendance and blocklist photos is similar to that of searching for event logs. The following is an example of searching for event logs.
RevFace15[TI] 1. Enter the user ID to be searched and tap OK. If you want to search for records of all users, tap OK without entering any user ID. 3. Once the record search completes. Tap the record highlighted in green to view its details. P a g e | 74 User Manual 2. Select the time range in which the records need to be searched. 4. The below figure shows the details of the selected record. Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 13 Print Settings Devices with a printing function can print attendance records when a printer is connected (this function is optional and only implemented in some products). Tap Print on the Main Menu interface. 13.1 Print Data Field Settings Select Data Field Setup on the Print interface. Toggle button to turn on/off the fields requiring a print. P a g e | 75 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 13.2 Print Options Settings Select the Printer Options on the Print interface. Toggle button to enable or disable the Paper Cut function. Remarks: To turn on the Paper Cut function, it is required to connect the device with a printer with paper cutting function, so that the printer will cut papers according to the selected printing information while printing. P a g e | 76 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 14 Autotest Select Main Menu, tap Autotest. It enables the system to automatically test whether the functions of various modules are working normally, including the LCD, Voice, Camera, and Real-Time Clock (RTC). Function Description Function Name Description Test All To automatically test whether the LCD, Audio, Camera and RTC are working normally.
RevFace15[TI] User Manual 15 System Information On the Main Menu, tap System Info to view the storage status, the version information of the device, and firmware information. Function Description Function Name Description Device Capacity Displays the current device's user storage, password and face storage, administrators, access records, attendance and blocklist photos, and profile photos.
RevFace15[TI] User Manual 16 Connect to ZKBioAccess IVS Software 16.1 Set the Communication Address 1. Device side Tap COMM. > Ethernet in the main menu to set the IP address and gateway of the device. (Note: The IP address should be able to communicate with the ZKBioAccess IVS server, preferably in the same network segment with the server address) 2. In the main menu, tap COMM. > Cloud Server Setting to set the server address and server port.
RevFace15[TI] User Manual Software side Login to ZKBioAccess IVS software, click System > Communication > Communication Monitor to set the ADMS service port, as shown in the figure below: 16.2 Add Device on the Software Add the device by searching. The process is as follows: 1) Click Access > Device > Search, to open the Search interface in the software. 2) Click Search and it will prompt [Searching……]. 3) After searching, the list and the total number of access controllers are displayed.
RevFace15[TI] User Manual 16.3 Add Personnel on the Software 1. Click Personnel > Person > New: 2. Fill in all the required fields and click [OK] to register a new user. 3. Click Access > Device > Control > Synchronize All Data to Devices to synchronize all the data to the device including the new users. P a g e | 81 Copyright©2021 ZKTECO CO., LTD. All rights reserved.
RevFace15[TI] User Manual 16.4 Real-time monitoring on the ZKBioAccess IVS Software 1. Click Prevention > Epidemic > Temperature Detection > Real-time monitoring to view all the personnel's events present under the Abnormal Temperature, No Masks, and Normal Records. The user data of abnormal body temperature is displayed on the Abnormal Temperature information bar automatically according to the set temperature threshold. 2.
RevFace15[TI] User Manual Appendix 1 Requirements of Live Collection and Registration of Visible Light Face Images 1) It is recommended to perform registration in an indoor environment with an appropriate light source without underexposure or overexposure on the face. 2) Do not place the device towards outdoor light sources like door or window or other harsh light sources. 3) Dark-color apparels other than the background color are recommended for registration.
RevFace15[TI] User Manual Requirements for Visible Light Digital Face Image Data The digital photo should be straight-edged, coloured, half-portrayed with only one person, and the person should be uncharted and in casuals. Persons who wear eyeglasses should remain to put on eyeglasses for getting photos captured. Eye Distance 200 pixels or above are recommended with no less than 115 pixels of distance. Facial Expression A neutral face or smile with eyes naturally open is recommended.
RevFace15[TI] User Manual Appendix 2 Privacy Policy Notice: To help you better use the products and services of ZKTeco (hereinafter referred as "we", "our", or "us") a smart service provider, we consistently collect your personal information. Since we understand the importance of your personal information, we took your privacy sincerely and we have formulated this privacy policy to protect your personal information.
RevFace15[TI] User Manual 2. All the functions of displaying the biometric information are disabled in our products by default. You can choose Menu > System Settings to set whether to display the biometric information. If you enable these functions, we assume that you are aware of the personal privacy security risks specified in the privacy policy. 3. Only your user ID is displayed by default. You can set whether to display other user verification information (such as Name, Department, Photo, etc.
RevFace15[TI] User Manual Eco-friendly Operation The product's "eco-friendly operational period" refers to the time during which this product will not discharge any toxic or hazardous substances when used in accordance with the prerequisites in this manual. The eco-friendly operational period specified for this product does not include batteries or other components that are easily worn down and must be periodically replaced. The battery's eco-friendly operational period is 5 years.
FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.