ZP19036 ASSEMBLY INSTRUCTIONS HUNTERSVILLE VINYL SCREEN 2-PACK ASSEMBLY INSTRUCTIONS ZP19036 (36” W X 45” H) 60 MIN Approximate assembly time for 2 screens If necessary, this screen can be trimmed down vertically to fit your custom space. Use a fine-toothed circular or hack saw. Rails will need to be re-spaced and configured accordingly. Want to see a video on how to assemble this product? Scan the QR code WWW.ZIPPITY-OUTDOOR.COM 1 VER.
ZP19036 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT k Check the inside of the larger pieces in your box for other materials packed inside. k When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. k We recommend an area approximately 5’x 8’ for unobstructed assembling. k You should not need to use excessive force when assembling components.
ZP19036 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B G Post Cap (4) C Post Anchor (4) ¾” x 1¼” x 16” Top and Middle Rail (4) 1½” x 1½” x 36” H D Joiner Clip (4) Post (4) ⅞” x 1½” x 44½” Rail End Cap (12) (6 installed, 6 loose) I E Pickets Picket #1 (4) ¼” x 1¼” x 41¹³̸₁₆” Picket #5 (4) ¼” x 1¼” x 37⅞” Picket #2 (4) ¼” x 1¼” x 40⁹̸₁₆” Picket #6 (4) ¼” x 1¼” x 37⅜” Picket #3 (4) ¼” x 1¼” x 39⁷̸₁₆” Picket #7 (4) ¼” x 1¼” x 37⅟₁₆” Picket #4 (4) ¼” x 1¼” x 38⁹̸₁₆” Picket #8 (2) ¼” x 1¼”
ZP19036 ASSEMBLY INSTRUCTIONS STEP 2: ASSEMBLE SCREEN FRAME STEP 2.1 C D F Identify the top/middle (C) and bottom (F) rails. Fit the three loose rail end caps (D) into the ends of the rails. STEP 2.2 STEP 2.3 B Position the two posts (B) as illustrated, and slide the top and middle rails down the posts, towards the locking tabs. Align the pre-drilled holes in the top and middle rails with the pre-drilled holes in the posts. Fasten together using (8) ¾” self-drilling stainless steel screws (I).
ZP19036 ASSEMBLY INSTRUCTIONS STEP 3: ASSEMBLE FENCE PANEL STEP 3.1 STEP 3.2 G Slide the bottom rail over the post towards the locking tabs, aligning the pre-drilled holes on the bottom rail with the pre-drilled holes on the posts. Then, slide the post anchors (G) into the bottom of the posts. 10” of the post anchors should be visible beyond the bottom of the posts. Fasten with (4) ¾” self-drilling stainless steel screws.
ZP19036 ASSEMBLY INSTRUCTIONS STEP 3.3 Repeat steps 1 through 3 for your second screen. STEP 4: INSTALL SCREEN INTO GROUND STEP 4.1 Move the screen to its final location, and identify the location of the posts. STEP 4.2 Attempt to push the unit into the ground as illustrated. All 10” of the post anchors should be inserted into the ground, so that they are no longer visible Push down on the top of posts with both hands. 6 WWW.ZIPPITY-OUTDOOR.
ZP19036 ASSEMBLY INSTRUCTIONS STEP 4.3 Step 4.3 is only to be completed if the ground is too hard: 1. Loosen the top 6” or 7” of the ground with a claw hammer as illustrated. 2. Add water to loosen soil. 3. Use a block of wood to protect the top of the post, and gently hammer the post into the ground. 2 1 3 Block of wood WWW.ZIPPITY-OUTDOOR.
ZP19036 ASSEMBLY INSTRUCTIONS STEP 4.4 Level the screen as necessary, then backfill and compact the excavated dirt. Level STEP 4.5 If your ground is really hard, you may need to dig a hole large enough to accommodate one post from each screen into the same hole. Backfill and compact dirt. 8” diameter x 10” deep. 8 WWW.ZIPPITY-OUTDOOR.
ZP19036 ASSEMBLY INSTRUCTIONS STEP 5: FASTEN JOINER CLIPS STEP 5.1 Fasten screens together by using (2) joiner clips (H) and (4) 1” self-drilling stainless steel screws (J) as illustrated. Bottom Rail Top Rail H J Angled Screens Application WWW.ZIPPITY-OUTDOOR.
ZP19036 ASSEMBLY INSTRUCTIONS STEP 6: FASTEN POST CAPS STEP 6.1 Push the post caps (A) down over the posts to lock into place. A 10 WWW.ZIPPITY-OUTDOOR.
ZP19036 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 support@zippity-outdoor.com 704-892-5222 877-234-6196 WWW.ZIPPITY-OUTDOOR.COM 12 WWW.ZIPPITY-OUTDOOR.
