User's Manual

Quick Installation Guide
AC1200 Wireless Dual Band Router
Suitable for: A800R
V1.1706
Information in this document is subject to change without prior notice.
Copyrights by TOTOLINK All rights reserved.Website:http://www.totolink.net
1. Please disconnect the power adapter and all cables during
thunderstorm weather;
2. Keep away from heat source and keep well ventilated;
3. Please pay attention to the waterproofing and moisture-proof
when storing, transporting and running.
4. Please use the power adapter provided with the router.
NOTE:
LED Indicators
WAN
LAN
The router is starting or WPS enabled
Status
The router is working normally
Press RST/WPS button for 5 seconds, the Status LED light
blinks fast
Power is off
The WAN port is connected
The WAN port is not connected
There is device connected to LAN port 1/2/3/4.
Fast
blinking
Off
On
On
Slow
blinking
Off
On
Off
No device connected to LAN port 1/2/3/4.
Ports and Buttons Description
WAN
LAN
RST/WPS
Connect with the power adapter
DC IN
Connect to ADSL modem or Internet Cable
Connect to PC or Laptop
Press for 1s, WPS enabled; press for more than 5s, Reset
function enabled.
Configure the Router
Run any Web browser. Enter 192.168.0.1 in the address bar.
http://192.168.0.1/
Enter admin for both User Name and Password, then click LOGIN.
admin
Now you can see the Easy Setup page. All basic settings could be done
here, including Internet Settings and 5GHz & 2.4GHz Wireless
Settings.
TOTOLINK_A800R_5G
TOTOLINK_A800R
Configure the Router
For more information, please go to www.totolink.net
Connect Wireless Network
After router settings, please follow below steps to connect wireless network:
2
Choose the SSID that you have set on Configure the Router. Enter correct
password. Click Connect or Next：5G Wi-Fi is recommended if it is available
for you.
8
The router’s Status interface turns up, showing all connection
information.
3
Wireless network connected. Enjoy your Wi-Fi
☺
.
For Mobile device users, please go to Settings—Wi-Fi to connect wireless network.
What can I do if the login page does not appear?
1.Check your computer’s IP address, make sure it is set to “Obtain an IP
address automatically”. Steps: right click Network—Properties—Change
adapter settings---Local Area Connection—Properties—Internet
Protocol Version 4(TCP/IPv4).
2.Make sure you enter the correct default access: 192.168.0.1.
Try again.
3.Use another web browser and try again.
4.Reboot your router and try again.
1
What can I do if I cannot access the Internet?
1.Check the Internet status by connecting a computer directly to the modem
via Ethernet cable. If it is not working properly, contact your Internet
Service Provider.
2.Setup your router again according to part 2 Configure the Router.
3.Reboot your cable modem (if have) and router, then try again.
2
By default, TOTOLINK router don’t have any wireless network password.
If you have set one, please log in to router’s Web Management page, go
to 5G Wireless---Basic Settings or 2.4G Wireless --- Basic
Settings to obtain or reset your password.
What can I do if I forget my wireless network Password?
5
What can I do if I forget the router’s Web login User Name
and Password?
In case you changed your router’s Login User Name and Password, we
suggest you reset your router to factory default settings by above operations.
Then use the following parameters to login the router’s Web interface:
Default IP address: 192.168.0.1, User Name: admin, Password: admin
4
How to reset the router to factory default Settings?
Keep the router powered on, press the RST/WPS button on router about 10
seconds, it will restore to factory default settings.
3
Click or icon on the right bottom of your desktop:
1
(Frequently Asked Questions)
FAQ
4
Connection Status PPPoE, Connected
Connection Time 0day，0hour，0minute，0second
IP Address 164.126.106.178
Subnet Mask 255.255.255.255
Default Gateway 164.126.96.1
DNS Server 202.96.134.133
MAC Address F4:28:53:00:01:84
B.Static IP. If you choose Static IP, please enter IP Address, Subnet
Mask, Default Gateway and DNS information provided by your ISP.
C.PPPoE. If you choose PPPoE, please enter the User Name and
Password provided by your ISP.
[e-mail]
●●●●●●●●●●●●●●●
Internet Settings. Connection Status shows physical connection
of router’s WAN port. Choose one Connection Type according to your
ISP(Internet Service Provider).
DescriptionConnection TypeNO.
No configuration, simply connect the WAN port to existing
Ethernet port by cable.
DHCPA
You’re required to enter IP Address, Subnet Mask, Default
Gateway and DNS information provided by your ISP.
Static IPB
You’re required to enter User Name and Password provided
by your ISP.
PPPoEC
A.DHCP. After choose DHCP, you can go on with the 5GHz & 2.4GHz
Wireless Settings.
5
5G Wireless Settings. You could customize your 5GHz wireless
Network Name(SSID) and Password. The WPA/WPA2-PSK is
recommended for Encryption.
TOTOLINK_A800R_5G
TOTOLINK
6
2.4G Wireless Settings. Verify or change your 2.4GHz wireless Network
Name(SSID) and Password. The WPA/WPA2-PSK is
recommended for Encryption. Click Apply.
TOTOLINK
TOTOLINK_A800R
7
Connected successfully. Please click Finish.
NOTE:
After you set the Key, please remember your SSID and the Key to connect with
your wireless LAN.
WPS: press for about 1~3 seconds, the system LED indicator keep solid
light, it means WPS working;
RST: press for about 5~8 seconds, the Status LED blinks quickly,the
device will restore to factory default settings.
TOTOLINK_A800R
TOTOLINK_A800R_5G
TOTOLINK_A800R
TOTOLINK_A800R_5G
TOTOLINK_A800R
TOTOLINK_A800R_5G
Default SSID
2.4G: TOTOLINK_A800R
5G: TOTOLINK_A800R_5G
Router
Wall Socket
IPad
Smart Phone
PC
DC IN
GPON Terminal
FCC warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must acceptany interference received, including interference that
may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with theinstructions,
may cause harmful interference to radio communications. However,there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.
Hardware Installation