User's Manual

Contents: Wireless Broadband Router, Power adapter, QIG, UTP cable,
Installation Helper CD.
Hardware Installation
If use ADSL access Internet, please comply with step 1, 2, 3, 4 in proper order in below diagram; If use residential broadband
access Internet, please complay with step 2, 3, 4, connect your router WAN port to the residential broadband directly.
After connected, please check if the indicator light is normal.
Name
WLAN indicator light
WAN indicator light
LAN indicator light
CPU indicator light
Normal Status
Flashing while data access
Light on or flashing
The corresponding indicator
light which connect to PC is
on or flashing
Flashing
Note
1. Please disconnect the power adapter and all cable during
thunderstorm;
2. Keep away from heat source and keep well ventilated;
3. Please pay attention to the waterproofing and moisture-proof
when storing, transporting and running.
4. The power supply must reached the rated current and power.
5. Put the router in flat places.
Set Up PC
Windows 2000 or Windows XP Operating System, please comply with following steps to set up.
Right-click “My Network
Places”, click “Properties”
Right-click “Local Area
Connection”, click “Properties”
Double-click “Internet Protocol
(TCP/IP)”
Choose “Obtain an IP address
automatically” and “Obtain DNS
server address automatically”,
click “OK”; go back to previous
interface and click “OK”
Windows Vista or Windows 7 Operating System, please comply with following steps to set up.
Click “Start— Control Panel— Network
and Internet— Network Connection”,
right-click “Local Area Connection”,
and choose “Properties”.
Double-click “Internet Protocol
Version 4 (TCP/IPv4)”
Choose “Obtain an IP address automatically”
and “Obtain DNS server address automatically”,
click “OK”; go back to previous interface and
click “OK”
Set Up Router
Please set up the router as following steps.
Run the Web browser.
Telephone
Wire
Telephone Wire
Telephone
Wire
Network
Cable
Network
Cable
Type 192.168.1.1 in the Web browser address bar,
and press enter, then click “Setup Tool”.
Input user name and password, and then click “OK”.
(The default user name and password are “admin”.)
Wireless Network Connection
Right-click “My Network
Places”, click “Properties”
Right-click “Wireless Network
Connection”, and click “View
Available Wireless Networks”
Confirm the wireless network SSID name,
choose one that you would like to connect,
then click “Connect”
Input the encrytion key and click “Connect”
Have connected wireless network, you can access
Internet through wireless mode.
For more information, please go to www.totolink.net
Internet
Access Mode
DHCP
PPPoE
Static IP
Parameters that provided by ISP (Service Provider)
User name & Password
Fixed IP address, Subnet mask, Default gateway
and DNS server
ISP do not provide any parameters, you can access
Internet when without router, no need set up the PC.
Access Internet Mode Judgement Method
Internet Access
Mode Settings
Wireless Settings
Router Security Settings
LAN/DHCP Server Settings
When power on, press the button for 5 seconds,
the system will be restored to factory settings.
Use auto setup wizard CD of TOTOLINK router,
can help you to set up the router by one-click.
Website: http://www.totolink.net
Quick Installation Guide
300Mbps Wireless N Router
Model: N302R Plus, IP04213
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should
be installed and operated with minimum distance between 20cm the radiator your
body: Use only the supplied antenna.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.