Configure DEV4: 1. Access the web server (http://192.168.2.254) of device from the Ethernet port. Caution If you configure multiple devices in the same PC, since the devices have the same default IP address but different MAC addresses, it may cause you unable to access the web server of device. If the situation happens, please try to clean the ARP table of your PC by DOS command “arp –d” then you can access the web server of device using the default IP address. 2. Use Wizard page to setup device. 3.
5. Press “Next>>” button then set the IP address of LAN interface. 6. Press “Next>>” button then select the “DHCP Client” for “WAN Access Type”. 7. Press “Next>>” button then select the “Client” for “mode” and change the SSID to “DEV4”. 8. Press “Next>>” button then select “None ” for “Encryption” then press “Finished” button.
9. Wait for refreshing web page. 10. Change the IP address of your PC to 192.168.3.x then access the web server by the new IP address “192.168.3.1” and use “Status” page check the setting. 11. If the “State” of “Wireless Configuration” is not “Connected” or you want to refresh the “RSSI “, please use “Site Survey” page to re-connect a AP.
Configure DEV5: 1. Access the web server (http://192.168.2.254) of device from the Ethernet port. Caution If you configure multiple devices in the same PC, since the devices have the same default IP address but different MAC addresses, it may cause you unable to access the web server of device. If the situation happens, please try to clean the ARP table of your PC by DOS command “arp –d” then you can access the web server of device using the default IP address. 2. Use Wizard page to setup device. 3.
5. Press “Next>>” button then set the IP address of LAN interface. 6. Press “Next>>” button then select the “Client” for “mode” and change the SSID to “DEV5”. 7. Press “Next>>” button then select “None ” for “Encryption” then press “Finished” button. 8. Wait for refreshing web page.
9. Access the web server by the new IP address “192.168.2.205” and use “LAN Interface” page to disable DHCP Server. 10. Wait for refreshing webpage. 11. Use “State” page to check setting.
12. If the “State” of “Wireless Configuration” is not “Connected” or you want to refresh the “RSSI “, please use “Site Survey” page to re-connect a AP.
Basic Settings Disable Wireless LAN Interface Disable the wireless interface of device Band: The device supports 2.4GHz(B), 2.4GHz(G) and 2.4GHz(B+G) mixed modes. Mode: The radio of device supports different modes as following: 1. AP The radio of device acts as an Access Point to serves all wireless clients to join a wireless local network. 2. Client Support Infrastructure and Ad-hoc network types to act as a wireless adapter. 3.
l Infrastructure: This type requires the presence of 802.11b/g Access Point. All communication is done via the Access Point. Ethernet AP AP Client #1 l AP Client #2 Ad Hoc: This type provides a peer-to-peer communication between wireless stations. All the communication is done from Client to Client without any Access Point involved. Ad Hoc networking must use the same SSID and channel for establishing the wireless connection.
The following table is the available frequencies (in MHz) for the 2.4-GHz radio: Channel No.
Advanced Settings These settings are only for more technically advanced users who have sufficient knowledge about wireless LAN. These settings should not be changed unless you know what effect the changes will have on your device. The default setting is optimized for the normal operation. For specific application, setting configuration will required highly attention to reach optimistic condition. Note: Any unreasonable value change to default setting will reduce the throughput of the device.
RTS Threshold The RTS threshold determines the packet size at which the radio issues a request to send (RTS) before sending the packet. A low RTS Threshold setting can be useful in areas where many client devices are associating with the device, or in areas where the clients are far apart and can detect only the device and not each other. You can enter a setting ranging from 0 to 2347 bytes. Beacon Interval The beacon interval is the amount of time between access point beacons in mini-seconds.
You should comply with the following instructions to roam among the wireless coverage areas. Note: For implementing the roaming function, the setting MUST comply the following two items. l All the devices must be in the same subnet network and the SSID must be the same. l If you use the 802.1x authentication, you need to have the user profile in these devices for the roaming station.
Configuring Wireless Security This device provides complete wireless security function include WEP, 802.1x, WPA-TKIP, WPA2-AES and WPA2-Mixed in different mode (see the Security Support Table). The default security setting of the encryption function is disabled. Choose your preferred security setting depending on what security function you need. WEP Encryption Setting Wired Equivalent Privacy (WEP) is implemented in this device to prevent unauthorized access to your wireless network.