User's Manual

ManualsBrandsZida Technologies ManualsElectronicsTomato

BIOS Setup

Mainboard User's Manual Page 29

UR2 Duplex Mode

This option is not available when UART is set to "Normal". Available options

are Half Duplex and Full Duplex. Default setting is "Half Duplex".

Onboard Parallel Port

Specifies the I/O port address of the onboard parallel port. Available settings

are Disable, 378h, 278h and 3BCh. Default setting is "378h".

Parallel Port Mode

Specifies the onboard parallel port mode. Available options are SPP, EPP,

ECP, ECP+EPP and Normal. Default setting is "SPP".

EPP Mode Select

Specifies the Enhanced Parallel Port specification version number. This option

only appears if the Parallel Port Mode is set to "EPP". The settings are

1.7 or 1.9. Default is N/A because the default setting for the Parallel Port

Mode option is not EPP.

ECP Mode USE DMA

This option only appears if the Parallel Port Mode option is set to ECP. It

assigns a DMA channel to the onboard parallel port. Available settings are

1, 3. Default setting is "3".

PWRON After PWR-Fail

Selects the power-on method after a power function. Options are Off, ON

and Former-Sts.

Game Port Address

Specifies the Onboard Game Port I/O address. Available settings are 201,

209, and Disabled. Default setting is "201".

Midi Port Address

Specifies the I/O address of the MIDI interface on the Onboard Game

Port. Available options are 300h, 330h 290h and Disabled. Default setting

is "330".

Midi Port IRQ

Assigns the IRQ line to the MIDI interface. Available options are 5 and 10.

Default setting is "10". This option is not available if the Onboard Midi Port

is disabled S-232 serial port.

Summary of content (14 pages)

PAGE 1
UR2 Duplex Mode This option is not available when UART is set to "Normal". Available options are Half Duplex and Full Duplex. Default setting is "Half Duplex". Onboard Parallel Port Specifies the I/O port address of the onboard parallel port. Available settings are Disable, 378h, 278h and 3BCh. Default setting is "378h". Parallel Port Mode Specifies the onboard parallel port mode. Available options are SPP, EPP, ECP, ECP+EPP and Normal. Default setting is "SPP".
PAGE 2
Power Management Setup ACPI Function Enabled / Disabled ACPI Function. Default setting is "Disabled". ACPI Suspend Type Specifies ACPI Suspend type. Options are : S1(POS), S3(STR) Instant On function. Default setting is "S1(POS)". Power Management Specifies Power Management Mode. Default setting is "User Define". Video Off Method Specifies Video off Method. Default setting is V/H SYNC+Blank. Video Off In Suspend Specifies Video off in Suspend. Default setting is "Yes". Suspend Type Specifies Suspend Type.
PAGE 3
HDD Power Down Specifies HDD Power Down Mode. Default setting is "Disabled". Soft Off by PWR-BTTN Sets Power Down Mode by PWR_BTTN. Default setting is "Instant-off". CPU THRM-Throttling Monitor CPU Temperature, slow down CPU Speed. Power On by Ring Enabled / Disabled Power on by Ring. Default setting is "Enabled". USB KB Wake-Up From S3 Enabled / Disabled USB KB Wake-up from S3. "Disabled". Default setting is Resume by Alarm Enabled / Disabled Resume by alarm. Default setting is "Disabled".
PAGE 4
PnP/PCI Configurations Reset Configuration Data Enabled / Disabled Reset configuration Data. "Disabled". Default setting is Resources Controlled By Sets the allocation of PCI resources. Available options are Manual and Auto(ESCD). Default setting is "Auto"(ESCD). BIOS automatically assigns resources. IRQ Resources When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt.
PAGE 5
PC Health Status CPU Warning Temperature Specifies CPU warning temperature value. Available options are 50°C/122°F, 53°C/127°F, 56°C/133°F, 60°C/140°F, 63°C/145°F, 66°C/151°F, 70°C/158°F and Disabled. Default setting is "Disabled". BIOS Setup Current System Temp. Current CPU Temperature Display System and CPU temperatures. Current System Fan Speed Current CPU Fan Speed Display Fan Speed status. Vcore/VDDq/3.3V/+5V/+12V/-12V/-5V/VBAT(V)/5VSB(V) Display System's Voltage status.
PAGE 6
Frequency / Voltage Control CPU Clock Ratio Select CPU’s core/bus frequency ratio. This setting has no effect on processors with frequency ratio locked. Available settings are between X8 to X24 of the CPU BUS Speed. Default setting is "X8" (Safe). Auto Detect PCI Clk Enabled / Disabled Auto detect PCI CLOCK. "Enabled". Default setting is Spread Spectrum This option turns on/off the clock generator’s Spread Spectrum feature to reduce Electromagnetic Interference (EMI) generated by high speed clock signals.
PAGE 7
Load Fail-safe Defaults BIOS Setup Fail-safe defaults contain the most appropriate values of the system parameters that allow minimum system performance.
PAGE 8
Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects.
PAGE 9
BIOS Setup Set Supervisor / User password When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password, up to eight characters and press. The new password will clear the previously entered password from CMOS Memory, you will be asked to confirm the Password. Type the password again and press , you may also press to about the selection and not enter a password.
PAGE 10
To disable password, just press when you are prompted to enter password. A Message <> will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter setup freely. If you select "System" at "Security Option" in BIOS Features Setup Menu, you will be prompted for the password every time. If you select "Setup" at "Security option" in BIOS Features Setup Menu, you will be prompted only when you try to enter Setup.
PAGE 11
Save & Exit Setup Type "Y" will quit the Setup Utility and Save the user setup value to RTC CMOS. BIOS Setup Type "N" will return to Setup Utility.
PAGE 12
Exit Without Saving Type "Y" will quit the Setup Utility and Without Saving the User setup Value. Type "N" will return to Setup Utility.
PAGE 13
Glossary
PAGE 14
Glossary A PS/2 Mouse & Keyboard Connector The Mainboard provides two on-board PS/2 connectors, one for the keyboard, and one for the mouse. PS/2 devices all have a standard 6-pin round shape connector. If you are already using a PS/2 mouse or keyboard, simply plug them into the corresponding connector. No jumper settings are necessary. B ATX Power Supply Connectors The Mainboard provides 20-pin ATX power supply connector, which incorporates standard +5V and +12V, 3.3V and soft-on/off signals.