Confidentiality: ■ O open □ S Confidential □ TS Confidential Document Category: R & D Doc Document Number: UM‐DNYS2C‐002 Version: V1.00 DNYS‐2C smart key Operating Manual Total 30 pages Zhuhai Unitech Power Technology Co., Ltd.
Approval for Documents: Department / Position Date Signature Prepared by Product development / software engineer Lu Haijiang, Tan Yi 2014.10.20 Checked by R & D Management Department /RQA Xu Lan 2014.10.20 Verified by Structure Department / Project Manager Yin Xuewen 2014.10.20 Countersigned by Hardware Department representative / hardware Chen Pengzhi 2014.10.20 Countersigned by Structure Department Representative / Structure Li Qiping 2014.10.
Copyright The copyright of the DNYS‐2C MiniSmart Key Operating Manual is owned by Zhuhai Unitech Power Technology Co., Ltd. No part of the Manual shall be copied or disseminated in any form by any means, electronically or mechanically, including photocopying or recording, or for any purpose, without written permission of Zhuhai Unitech Power Technology Co., Ltd. (c)Copyright 2014 Zhuhai Unitech Power Technology Co., Ltd. All rights reserved.
Guide READING GUIDE Manual Objective: The Manual mainly provides operating instructions on DNYS‐2C Smart Keys and auxiliary iAdapterE-1 transmission adapter and iCDZE-1 recharge stand products supplied by Zhuhai Unitech Power Technology Co., Ltd. To enable product users to have a basic understanding of product functions, performance and characteristics and grasp product operating and maintenance methods.
Foreword The products are mainly used in power industry interlock by foreign terminals, such as substations, power plants, etc. It is capable to receive operating orders from Smart interlock hosts, and then to operate all kinds of locks in strict operating orders. In Smart interlock system, the smart key is used as a handheld device between the host and device on site, and regarded as one of the most critical system components.
Table of Contents CHAPTER 1 OVERVIEW ......................................................................... 1 1.1 INTRODUCTION ............................................................................. 1 1.2 SCOPE OF APPLICATION .................................................................... 1 1.3 FUNCTIONS AND FEATURES ................................................................ 1 1.4 MODEL AND CONFIGURATION ............................................................
CHAPTER 4: PARAMETER SETTINGS .....................................................27 4.1 AUTO POWER‐OFF ....................................................................... 27 4.2 AUTO SLEEP MODE ....................................................................... 27 4.3 INTERFACE BRIGHTNESS ................................................................. 27 4.4 DISPLAY L ANGUAGE ...................................................................... 27 4.5. INTERFACE THEMES .........................
Chapter 1 Overview 1.1 Introduction DNYS‐2C smart key is a new type of OLED color‐screen smart key based on the “Double‐less” technology of the company, based on our application and development experience over the years, which can be operated in conjunction with JOYO series of microcomputer safety interlock systems.
Available in recording function, equipped with large‐capacity recording & storage device, available to be selected according to needs. 9 OLED color screen to enhance the visual effects. 9 High‐contrast, multi‐line Chinese character display. 9 OLED screen, adjustable display brightness, thus to meet the needs of different users. 9 Friendly interface, easy to use, simple.
4. The smart key is product integrating machinery, optic, and electric technologies, with a complex internal structure, except as authorized by its manufacturer, please do not disassemble to avoid any damage to internal components. 5. Please keep its data transmission ports clean, to avoid any damage to data transmission performance. 6. Smart key is a precision power handheld devices; please avoid damage and abnormality resulting from strong shock or falling. Chapter 3 Operation 3.
‐‐‐‐‐‐ High speed infrared IRDA transmission device for exchanging data with mis‐operation prevention hosts. 3.2 Operations 3.2.1 Basic operations ¾ Power‐on (1) Ensure that the smart key is available to be powered. If the battery runs low, the smart key can’t start, please operate in accordance with the second step. When the power is enough, please operate in accordance with the third step.
¾ Menu Operation In the standby interface, press the “Menu” key to enter main menu: Then press the UP or Down keys to browse the whole main menu, as shown below: Thereinto: z The “Receive” is the default option on the menu, indicating the option is selected. Now a user presses the Down key to select the next option on the menu, similarly, it is available to press the Up key to select the previous option.
Thereinto: z Press the Return key to the previous menu。 When the key is being charged on the transmission adapter, the key can receive synchronous data if the user sets host system to the synchronous state, and the smart key enters the synchronous interface. When the key starts receiving synchronous data, it can display the following interface, the progress bar shows the receiving progress of synchronous data.
When the smart key has processed and saved the received data, the key can switch to the following operating interface automatically. A user can operate on site now in accordance with the displayed content. 3.2.
Rotate the smart key to open the mechanical coding lock at this moment and then switch. When the correct operation is completed, the smart key can ring “beep” and prompt “Operation finished” Then the operator can continue the next operation. Note: for exmaple, in “Confirm 61E Breaker operation”, if the inserted lock’ code is not consistent with the displayed in the key, the key can ring “beep” three times or make a voice prompt “Error, Please Check.
Switch the breaker at this moment, the key rings “Beep” and displays “the operation is completed, please continue!” indicating that the key has detected the completion signal. It is available to unplug the smart key and continue.
A user can operate electric coding lock or mechanical lock as needed, then the user chose to insert the mechanical locks and Rotate the smart key to unlock, the smart key rings “beep” and displays the following information: It indicates that the smart key has completed its working; the user can remove the smart key and continue the next operation. While inserting the corresponding electric coding lock, it is available to operate in accordance with the steps described in “3.4.
z Electriferous Detection(electroscope, high‐voltage live locking device) Insert the smart key into the corresponding electroscope for further electriferous detection, when the smart key displays electriferous detection and the next option.if the electriferous detection is correct, and the operation is successful, it is available to enter the next step.
And produces rapid alarm sound “Beep…Beep…Beep…”indicating the circuits are electriferous, and can’t enter the next operation. When the smart key displays the following information, and rings “Beep,” it indicates that the circuits aren’t electriferous, remove the smart key from the electroscope and enter the next operation.
After operation is completed, please lock as prompted by the smart key; insert the smart key. When it prompts the lock code is correct, rotate the smart key to lock: The above is operation steps for the first type of fixed program lock. Secondly, as for one‐way fixed program lock (one‐way lock), taking “62E Line: Open Breaker” as an example.
Thereinto: The operating procedures for the second type are only half of the first type’s. the whole operation can be completed only after unlocking or locking ends.
The above is operation steps for the third type of fixed program lock. The third category of fixed program lock operation is complete. Thereinto: As for the third type of fixed program lock, its unlocking is similar with the first type’s, the only difference is that the third type of fixed program lock operates twice on two fixed program locks on the same device, while the first type operates a fixed program lock.
3.2.6 Browse orders z Browse Order Contents The order browsing functions as browsing and checking the content of the current operating order in the smart key. Select the Main Menu‐ “Browse” – > “Current” Contents to enter the option. If the smart key has not any operating order, it will prompt “No operation order to review”, if the smart key has received the operating order, press the Enter key to show the contents on the first item of the current operation order.
3.2.7 Function z Synchronization See details in the section 3.2.2 Synchronization z Check Code The option is to check the code value or RFID value of the current lock. And it is also capable of showing the corresponding device name. Select the Main Menu‐ “Function” –> “ChkCode” to enter the option, press the Enter key to read the lock code or RFID code value. The code’s equipment name can be shown if exists. If the device name doesn’t exist, it can show “This Dev isn’t exist”.
Insert the smart key step into the skipping key, the smart key begins to identify the skipping key and execute skipping. If skip operation is successful 5 seconds later, the smart key displays as follows: If fails, the key displays: Please remove the smart key from the skipping key when the skipping operation is successful, the smart key loads the next operation automatically, and continues its operations.
Thereinto: z Press the Enter key to delete the order, the smart key will automatically return to the main menu; or press the Return key to directly return to the main menu, rather than to delete the operation order. z Deploy This menu provides a series of debugging programs special for professional test personal, and such test options are unavailable to final users for further safe and reliable operations.
3.2.8 Settings z NetWork This menu provides a debugging tools special for professional deployment user, which is not available for normal use. You have to enter the access password before enter the setting menu for further operation. z VoiceFunc Select “Settings” ‐> “VoiceFunc” to enter this menu, and then set voice‐related options by operating various sub‐menus.
After the recording function is enabled, “record” or “ stop” button will appear on the user interface, as shown below, It is available to start up or stop recording as needed. Recpress Select “VoiceFunc” ‐> “Recpress” to enter Audio compression interface, and press the “Close” button or the “Open” button to disenable or enable the function. After the function is enabled, the system will compress and save recorded audio, thus saving memory space.
RecTest Select “VoiceFunc” ‐> “RecTest” to enter Recording test interface, and press the “Close” button or the “Open” button to disenable or enable the function.
PlayTest Select “VoiceFunc” ‐> “ PlayTest” to enter Playing test interface, and these audio files are stored in the REC folder directory; a user can select an audio file by the “UP “ and “Down” buttons, and then play or delete such a file. z Brightness The menu functions as setting backlight brightness, Select “Settings” ‐> “ Brightness” on the main menu, to enter the menu.
z Time Setting Select “Time” ‐> “Time” to enter the option, and then move the cursor by operating the Down button, and adjust the value by the Up button. Press the Enter key to confirm after setting is completed. z Background The menu functions as setting the background pattern of the user interface, Select“Settings” ‐> “ Background”to enter the menu, as shown as below. Press the Up or Down key to select the background image, press the Enter key to set, press the Return key to cancel the operation.
z Language Select “Settings” ‐> “Language” to enter the option, and the optional languages include Chinese and English. Chinese Select “Language” ‐ > “Chinese” to enter, and press the Enter key to select the Chinese. English Select “Language” ‐ > “English” to enter, and press the Enter key to select the English.
3.2.9 About Enter this option to check the software version, model number and manufacturer name. Thereinto: A user can press the return key directly to the main menu interface.
Chapter 4: Parameter settings 4.1 Auto Power‐off The smart key will automatically power off if continues its standby state for 6 minutes, If it is being charged or fully‐charged state, or being under cycle unlocking test for electric‐controlled lock or discharging test, the key will cancel the auto power‐off, till the above state is canceled. 4.
Chapter 5 Display Descriptions Under the standby mode, the green indicator flashes every 5 seconds, The blue backlight lights up under key‐operating state, From start‐up, running to normal operation, related prompts show the current state of the key, and part of prompts s are shown in the following table: Prompt Description Hardware fault,format is failed! iNand mass storage device is damaged Battery error! The battery is improperly contracted or the battery is damaged.
Chapter 6 Products Maintenance 6.1 Upgrade maintenance If need to upgrade and maintain the product, please contact your local service personnel. 6.2 Routine maintenance Please read the operating manual in details as well as Troubleshooting as shown in the next section to implement routine maintenance. 6.3 Troubleshooting Troubles Causes Solutions The smart key cannot synchronize , or is abnormal in synchronization. 1. Battery voltage is low. 2. synchronization program is incorrectly operated. 3.
1. The internal components of the lock are unsmooth. The smart key shows 2. The ring is blocked by “Code correctly, please external components. unlock the mechanical 3. Battery voltage is low. lock.” But the mechanical 4. coding lock still cannot be Internal unlocking components of the smart opened. key do not work. 5. The mechanical coding lock is damaged. When operating the breaker, the breaker can not be connected; though the smart key shows “Electric coding lock can be opened.” 1.
