Preface Welcome to the Pantum Series products! We heartily appreciate your using of Pantum Series products! To protect your vital interests, please carefully read the following statements. Legal Notice Trademark Pantum and Pantum logos are registered trademarks of Zhuhai Pantum Electronics Co.,Ltd. Microsoft® , Windows® , Windows Server ® and Windows Vista® are trademarks registered by Microsoft Corporation in the United States or other countries/regions.
The product can only be used safely in the non-tropical areas at an altitude no higher than 2000 meters. Safety Precautions Laser Safety The laser radiation is harmful to the human body. Since laser components are completely sealed in the printer, laser radiation will not leak. To avoid laser radiation, please do not randomly disassemble the printer! The printer follows the provisions of Class 1 laser products under CFR standard.
Precautions Precautions before Using the Printer: 1.Read and understand all instructions; 2.Familiarize yourself with the basic principles associated with operating electrical appliances; 3.Comply with all warnings and instructions marked on the equipment or specified in the manual supplied with the equipment; 4.If the operating instructions conflict with the safety information, please refer back to the safety information, as you may have misunderstood the operating instructions.
power supply; 20.As the Class 1 equipment, the product must be connected to the power supply outlet with protective grounding line when using; 21.This product should be placed according to the shipping marks on the product package box during delivery; 22.This product is a kind of low-voltage equipment.
This symbol indicates that, at the end of your product’s life, it must not be discarded as domestic waste. Instead, you should dispose of your used equipment at a designated collection point for the recycling of waste electrical and electronic equipment. Ref: EU Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). Please contact your distributor / supplier for further information. This product is suitable for indoor use only.
1.Before Using the Printer 1.1.
Toner cartridge Drum component USB Interface Cable Power Cord CD Quick Setup Guide Pantum Warranty Note: • The Pantum Warranty may not be attached in some regions. 1.3.
Side view 1 Output Bin For storing the printed paper. 2 Control Panel Indicate printer status to conduct set operation. 3 Output Tray To prevent the printed paper from falling. 4 Front Cover To open the front cover to take out the laser toner cartridge. 5 Manual feed tray For placing mediums that are printed in manual feed tray. Power switch Turn the power on or off and press this button under Ready state to enter energysaving mode.
11 Paper length deflector of auto feed tray Slide paper length deflector to adapt to paper length. 12 Clip of extended tray of auto feed tray For adjustment of length extension of the tray . Rear View 1 USB Interface For connecting product to computer with USB cable. 2 Network Interface For connecting product to network with network cable. 3 Power Interface For connecting product to power with power cord. 4 Rear Cover For paper release when it gets jammed.
Longevity of drum component About 12000 Pages(Based on ISO 19752 standard) Service life of toner cartridge Type Average Print Volume Standard-volume toner cartridge About 1500 Pages(Based on ISO 19752 standard) High-volume toner cartridge About 3000 Pages(Based on ISO 19752 standard) Note: • The model is subject to increase without notice. • Consumables capacity may vary with different using types.
No. Name Functions 1 LCD Display Display operation interface and product information. Indicate Wi-Fi connection status (applicable to Wi-Fi model only). 2 Wi-Fi indicator/save toner indicator 3 Toner cartridge/status indicator Indicate the status of toner cartridge and printer (please refer to Chapter 1.5.2.1) 4 Menu Open the main menu of control panel 5 OK Confirm the selection on screen 6 UP Indicate the on/off of save toner function (applicable to non-Wi-Fi model only).
Open save toner function(applicable to non-Wi-Fi model only). 11 Cancel Execute cancel operation LED control panel No. Name Functions 1 Drum/paper status indicator Indicate the status of paper and drum component (please refer to Chapter 1.5.2.2) 2 Toner cartridge/status indicator Indicate the status of toner cartridge and others other than paper (please refer to Chapter 1.5.2.2). Press this button for more than 2s to cancel current printing operation under normal printing condition.
toner indicator model only) model only) 1 Die out Wi-Fi disconnected and sleep mode Turn save toner state function and sleep mode 2 Blue indicator blinks Wi-Fi connecting None 3 Blue indicator normally on Wi-Fi connected Turn on save toner function Display meanings of toner cartridge / status indicator are as follows: No.
status indicators 1 Die out Sleep mode 2 Green indicator normally on Normal drum, paper out failure 3 Red indicator normally on Drum component error (uninstalled drum component, unmatching drum component, invalid drum component), paper error (paper out, paper jam, paper feed failure) 4 Orange indicator normally on Drum component is about to end its expected service life Display meanings of toner cartridge/status indicator are as follows: No.
2.Paper and Print Media 2.1.
This printer supports using the special paper for printing. Special paper includes: label paper,envelope, transparent film, thick paper,carton paper, thin paper. Note: • When using special paper or print media, be sure to select matched print type and size in the print settings so as to get the best print effect. Please observe the following standards: Types of Print Media Correct Practices Incorrect Practices Use labels with no exposed lining paper only. Labels shall be put flat when using.
2. Slide the clip of extended tray of auto feed tray, paper length deflector and paper width deflector to the slot suitable for paper size, in order to match paper length and width. Note: • Do not overly squeeze the "paper length guide" and "paper width guide", otherwise it could easily lead to deformation of paper. 3.Before loading paper, please unfold the stacked paper to avoid a paper jam or feed error, and then load the paper into the tray printside down.
4.Raise the output tray to avoid the printed paper from slipping and falling, or immediately remove the printed document after the printing is complete. Note: • It is recommended that you raise the output tray to prevent the paper from slipping and falling after printing. If you choose not to raise the output tray, we recommend that you immediately remove the printed paper from the printer.
2. Open manual feed tray 3. Slide the paper deflector of manual feed tray to match the two sides of paper. Do not use excessive force; otherwise, paper will be made jammed or skewed.
4. Put a flat printing medium into the manual feed tray with both hands. Note: • The printer will enter manual feed mode automatically when you put papers inside the manual feed tray. • Please put one printing medium inside the manual feed tray each time and put in another piece after finishing printing. • Put the printing medium inside the manual feed tray with the printing side up; the top of paper should be put inside first. 5.
Note: • After printing, please take out printed papers output from printer immediately. Stacked papers or envelops will lead to paper jam or wrapped paper. 2.4.Non-printable Area The shaded area indicates the non-printable area. Usage Paper Size Top and bottom margins (A) Left and right margins (B) A4 5mm(0.197inch) 5mm(0.197inch) Letter 5mm(0.197inch) 5mm(0.197inch) Printing 2.5.
3.Driver installation and uninstallation 3.1.Driver installation based on Windows system • Before installing the drive, you need to learn about printer model by printing printer information page out and check the product name (please refer to Chapter 9.4 for printing methods). • In case of covering the installed driver, the installation language cannot be changed. Please uninstall the printer driver and then install the driver of new version.
3. Connect network cable to the network interface of printer, to make sure the printer is connected to computer network (please refer to Chapter 4 for network setup). 4. Insert the installation CD companying with the printer in the CD driver of computer and operate Autorun.exe installation program. 5. Read and agree to the licensing agreement, select installation language and printer model, select “Cable network connection (N)” and then click “Install”. 6.
“Install the printer from the list with a hostname”. • If IP address or host name is added manually, you need to know the IP address of the printer connected or host name. If they are not made clear, please print the “NetConf Pg” and view “IP Address” and “Host name” (Please refer to Chapter 9.4). 8. The system starts to install driver, and it may take several minutes. 9. After installation is finished, “Installation Complete” interface will pop out, and it will be closed automatically in about 3s. 3.1.3.
6. After wireless network setup succeeds, the installation program will search for printer automatically, and it may take a while. 7. Select the printer needs to be connected and click “Next”. Note: • If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again. • If you want to install printer driver in the name of host, please tick the “Printer Name” you need to connect and “Install the printer from the list with a hostname”.
3. Insert the installation CD companying with the printer in the CD driver of computer and operate Autorun.exe installation program. 4. Read and agree to the licensing agreement, select installation language and printer model, select “Wireless network connection (W)” and then click “Install”. 5. Select “No, the printer has been connected to wireless network” on the wireless setup window popping out, and then click “Next”. 6.
Note: • If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again. • If you want to install printer driver in the name of host, please tick the “Printer Name” you need to connect and “Install the printer from the list with a hostname”. • If IP address or host name is added manually, you need to know the IP address of the printer connected or host name.
Mac 10.11 is taken as the example in the following operation. The information on your computer screen may differ because of multiple operating systems. 1. Turn the power of printer and computer on. 2. Insert the CD companying with printer in the CD driver of your computer, and double click Pantum X Series installation package. (X in Pantum X Series represents product model.) 3. Click “Continue”. 4. Read licensing agreement and then click “Continue”. 5.
8. Click “Continue Installation” on the prompt window popping out. 9. The system will finish driver installation automatically. • If USB cable is used to connect the computer and Wi-Fi model, the window to prompt wireless network setup will pop out during driver installation process, as shown in the diagram above. Click “Yes” to set up the wireless network of printer with wireless network setup tool (refer to Chapter 5.1.1).
3.3.2.Addition in wired network connection mode 1. Turn the power of printer and computer on. 2. Connect the computer to wired network. 3. Connect the network cable to the network interface of printer, and make sure the printer is connected to the computer network (Please refer to Chapter 4 for network setup). 4. Enter the “System Preferences” – “Printers & Scanners” of computer. 5. Click button to select “Add Printer or Scanner”. 6.
4.Wired network setup (applicable to wired network models) In case printers support wired network printing, they can be connected to network to control printer to print in wired network mode. 4.1.Set IP Address The IP address of the printer may be automatically obtained through DHCP function or set manually. 4.1.1.Automatic Setting DHCP automatic setting function is enabled by default on the printer. 1.Connect the printer to the network through a network cable and complete the startup preparation work. 2.
5.Wireless network setup (applicable to Wi-Fi models) Wireless network connection type is divided into basic structure mode and Wi-Fi Direct mode. If you have problems with wireless network setup, please refer to Chapter 5.3 Wireless Network Setup FAQs. Basic structure mode: connecting to a wireless device via router 1. Access point (wireless router) 2. Wireless network printer 3. Computer connecting to access point via wireless network 4.
Note: • The SSID you selected should be consistent with the SSID of access point (wireless router) connected to your computer. • If the wireless network list is empty, please check if the access point (wireless router) is on, or if the computer is within the wireless network scope, and then click “Refresh” to search again. • If the SSID you need to connect is not in the SSID list searched out, please tick “Enter SSID Manually” to set up it manually (refer to Step 3.2.) 3.
2) WEP: Send and receive data via security key by using WEP (Wired Equivalent Privacy). WEP key is applicable to 64-digit and 128-digit encrypted network and can contain numbers and letters at the same time. 3) WPA/WPA2: it is the pre-shared key (PSK) of Wi-Fi protected access which connects wireless device and access point via TKIP or AES encryption (WPS-Personal). The working length of WPA/WPA2 is within the PSK of 8-63 characters.
3. Select “Advanced” and then select “Wi-Fi Direct” in advanced WLAN interface. 4. Select printer SSID on direct interface to launch a connection invitation. 5. Press “OK key” to confirm connection when the panel lead to prompts whether to connect to start Wi-Fi Direct connection. Note: • In case of auto connection mode, the mobile device will start to connect automatically after initiating connection invitation without panel confirmation. 5.2.2.2.
• Inspect if the power switch of access point (wireless router) is turned on. • The printer cannot find the SSID of the access point (wireless router) you need to connect, please check the SSID of access point and try to connect again. • Every time when the setup of access point (wireless router) is changed, you must set up the wireless network of printer again. 3. Connection failure • Please inspect if the safe mode and password of access point (wireless router) and printer is correct.
6.Web server You can manage printer setup via the embedded Web server. 6.1.Visit the embedded Web server 1. Turn on the power of printer and computer. 2. Connect the printer to network to ensure that the printer is connected to the network where the computer is connected to (please refer to Chapter 4 or Chapter 5 for network setup method). 3. Input the IP address of printer in the address bar of Web browser to visit the Web server imbedded in printer.
2. In case of wireless network model, the printer can be connected to wireless network via wireless network setup tools or Wi-Fi Protected Setup(WPS) (please refer to Chapter 5.1.2). 6.2.1.1.IPv4 setup IPv4 address of the printer is divided into DHCP auto assignment and manual setting, and the DHCP auto assignment function is on by default. You can set up the IPv4 address of printer manually to set up fixed IPv4 address for the printer. 1. Turn on printer power to connect printer to network. 2.
You can add mail address contacts, set up e-mail notification, set up sleep time and recover factory settings via machine setup page. 6.2.3.1.Set up e-mail notification If you set up e-mail notification, an e-mail will be sent to the mail address specified by you when abnormality such as paper out occurs. You can receive emails only if you made correct email setup. Please consult your network administrator for detailed setup steps.
7.Print 7.1.Print Function You can set the print function through "Start"-"Devices and Printers"- select corresponding printer- right click – set print function in "Printing preferences". Some functions are as follows: Functions Diagram Automatic Two-Sided Printing Collate Print Reverse Print N-in-1 Poster Print(for Windows Operation System only) Zoom Print Custom Size Note: • Windows 7 is taken as example in the above description.
Before printing, please make sure mediums of corresponding quantity have been installed inside the auto feed tray, and there is no printing medium in the manual feed tray. Note: • For precautions on loading paper, see Chapter 2. • For the type of media to be printed with the automatic feeder tray, see Chapter2.1. 7.4.2.Printing with manual feed tray When you put papers in the manual feed tray, the printer will enter manual feed mode.
2. Make the backside of duplex unit up. 3. Adjust paper size slide to A4 or Letter position to finish setting up. 4. Install the duplex unit in the printer. 7.5.2.How to carry out auto duplex printing 1.Open the print job to be printed from the application (such as a Notepad). 2.Select Print from the File menu.
3. Select printer of the corresponding model. 4. Single click “Preferences” for printing setup. 5. Select the “Duplex” in “Basic” tab and then select “Long Edge” or “Short Edge”.
6. Single click “OK” to finish printing setup. Click “Print” to realize auto duplex printing. 7.6.Fine mode printing High printing quality can be realized by setting up fine printing mode. Set up fine mode in the basic page of printer preference (please refer to Chapter 7.5.2 for detailed steps). After setup, fine printing mode can be realized.
7.7.Mute printing Low-speed printing with low noise can be realized by setting up mute printing. The operating steps of mute printing are as follows (applicable to printers that are installed via USB connection) Windows 7 is taken as the example in the following operation. The information on your computer screen may differ because of multiple operating systems. 1. Enter the “Start menu” – “Control Panel” –view “Devices and Printers”. 2.
• Printers with LCD control panel can be set to mute printing with keys on control panel directly, please refer to Chapter 9.1.4. 7.8.Open Help Document You can open the "Printing preferences" and click "Help" button (for Windows Operation System only). The help document contains the user guide where you can find the information on print settings.
8.Mobile Print 8.1.Android device mobile printing 8.1.1.Pantum Pantum is a free App with which you can print TXT files, photos and webpages from you smart phone or tablet directly. 8.1.1.1.Operating systems and Apps supported by Pantum Pantum is applicable to Android 4.0 or operating systems of higher version. Pantum only supports TXT file, photo and webpage printing currently. 8.1.1.2.How to download Pantum App 1. You can download it from its official website http://www.pantum.
4. Select corresponding option in the main menu (e.g.: print from the album), tick the photos you need to print and then click “Print Settings”. 5. Select the printer needs to be connected, set printing parameters and then click the “Print” button, the printer will start to print. Note: • If printing fails, please inspect if the Android device is connected to the wireless network where the printer is connected to.
2.Set the "Mopria print service" as "On". All other printing plug-ins should be shut down when you use Mopria mobile printing function. The printing steps may varied by applications, taking Adobe Reader as an example for explanation. 1. Turn on printer power. 2.Connect the Android mobile device with wireless network of the printer (Please refer to Chapter 5 for how to connect). 3. Open the files you need to print with Adobe Reader on the Android device. 4. Click . 5.Tap "Print". 6.
several seconds, the mobile device will connect to the printer. 4. Select the content to be printed and set printing parameters according to needs. 5. Click print and the printer will start to print. 8.2.IOS device mobile printing 8.2.1.Pantum Pantum is a free App with which you can print TXT files, photos and webpages from your smart phone or tablet directly. 8.2.1.1.Operating systems and Apps supported by Pantum Pantum is applicable to IOS 6.0 or operating systems of higher version.
4. Select corresponding option in the main menu (e.g.: print from the album), tick the picture you need to print and then click . 5. Select the printer needs to be connected, set printing parameters and then click the “Print” button, the printer will start to print. Note: • If printing fails, please inspect if the IOS device is connected to the wireless network where the printer is connected to.
If you select other printers (or no printer), please click printer option and then select your Pantum printer. 7. Set printing parameters such as number of copies to print. 8.Tap "Print". Note: • If printing fails, please inspect if the IOS device is connected to the wireless network where the printer is connected to. • If the IOS mobile device did not detect any printer, check whether the printer is powered on and the printer is turned on.
9.General Settings This Chapter mainly introduces some general settings. 9.1.System Setting 9.1.1.Language Setting "Language Setting" is used to select the language to be displayed on the control panel. 1)Press "Menu" to enter the Menu Settings interface. 2)Press "OK" to select the "1.System Setting" option. 3) Press “OK” key to select “1.Language Set” option to set language, as shown in the below figure: 9.1.2.
Note: • In sleep mode, the printer can be woken up by pressing any key or sending printing work. • Sleep time of network printer can be set with the embedded Web server (Please refer to Chapter 6.2.3.2). 9.1.3.Toner Save You can select the save toner mode which can reduce toner consumption and reduce printing cost. When save toner mode is “on”, the printed color will be lighter. Save toner mode is “off” by default. 1)Press "Menu" to enter the Menu Settings interface. 2)Press "OK" to select the "1.
9.1.5.Restore Factory Settings “Recover factor settings” is used to recover the default settings of printer. The printer will restart itself automatically after recovering factory settings. 1)Press "Menu" to enter the Menu Settings interface. 2)Press "OK" to select the "1.System Setting" option. 3UHVV GLUHFWLRQ NH\ Ÿ RU ź WR VHOHFW WKH 5HVWRUH 6HW RSWLRQ DQG SUHVV 2. Note: • Factory settings of network printer can be recovered via embedded Web server (please refer to Chapter 6.2.4).
9.3.Network Information You can check network information via network information. 1)Press "Menu" to enter the Menu Settings interface. 3UHVV GLUHFWLRQ NH\ ³Ÿ´ RU ³ź´ DQG VHOHFW ³ 1HWZRUN ,QIR´ RSWLRQ DQG SUHVV ³2.´ NH\ WR YLHZ ³ZLUHG QHWZRUN LQIRUPDWLRQ´ ³ZLUHOHVV QHWZRUN LQIRUPDWLRQ´ DQG ³:L Fi Direct information”. 9.4.Print information report You can print information report by operating control panel.
3) Press “OK” key to enter information report print. You can print product report according to needs. Product reports that can be printed include demonstration page, information page, menu structure page, network setup page, Wi-Fi hotspot list page, PCL font list page and PS font list page. Note: • The product report above is the most complete version, and may be different from the product report of model that you actually use.
10.Routine Maintenance Note: • Printer appearance may differ because of different models and functions, so the schematic diagram is only for your reference. 10.1.Cleaning the Printer Note: • Please use mild detergents. • Some parts of the printer may still be hot for a short period after use. When opening the front cover or rear cover to clean the parts inside the printer, please do not touch the parts in the shaded area as shown in the following picture. 1.
4. Wipe the LSU lens of printer gently with dry lint cloth. 5. Open the auto feed tray and wipe the pickup roller gently with dry lint cloth. 10.2.Toner cartridge and drum component component maintenance 10.2.1.About toner cartridge and drum component component 1. Application and maintenance of toner cartridge Please use the original toner cartridge for better printing quality.
• Do not take the toner cartridge out of its package unless it will be used immediately. • Do not refill the toner cartridge without permission; otherwise, the damages caused will not be included in the scope of warranty of the printer. • Please place the toner cartridge in cool and dry places. • Please do not place the toner cartridge near ignition sources, as the toner inside it is inflammable and may cause fire. • Please pay attention to toner leakage while it is taking out or disassembled.
3. Press the blue button on the left side of drum component with left hand and lift the toner cartridge handle with right hand at the same time to take the toner cartridge out. 4. Open the package of the new toner cartridge and hold the toner cartridge handle to shake it left and right for 5 – 6 times, so that the toner inside can be uniformly dispersed. 5. Pull the seal out and take the toner protection cover out. 6. Install the drum component along the inner track to finish installing toner cartridge.
8. Close the front cover. Drum component replacement steps: 1.Power off the printer. 2. Open the front cover and take the laser toner cartridge out along the track. 3. Press the blue button on the left side of drum component with left hand and lift the toner cartridge handle with right hand at the same time to take the toner cartridge out.
4. Open the package of new drum component, take the protection device of drum component, and put the drum component on a horizontal table. 5. Install the drum component along the inner track to finish installing toner cartridge. 6. Take the drum component with toner cartridge installed and install it inside the printer along the inner track of printer to finish installing. 7. Close the front cover.
11.Troubleshooting Please read this section carefully. It may help you to solve common problems encountered during the printing process. If the problems persist, please contact Pantum Aftersales Service Centre. Prior to handling common problems, first check that: • The power cord is connected correctly and the printer is powered on. • All of the protective parts are removed. • The toner cartridge is installed correctly. • The paper is correctly loaded into the tray.
recover printing automatically. 11.1.2.Paper jam of manual feed tray 1.Gently pull the jammed paper out. 2. After taking papers jammed out, open and close the front cover and the printer will recover printing. 11.1.3.Middle jam Note: • When papers jammed in the middle are taken out, please pay attention and do not touch the shaded area shown below, in order to avoid burn.
1. Pull paper tray out. 2.Gently pull the jammed paper out. 3. Install paper tray.
4.Open the front cover. 5. Take the laser toner cartridge out along the track. (For the purpose of preventing printing quality from affecting by the exposure of photosensitive drum, please put the laser toner cartridge inside the protection bag or warp it with thick paper). 6.Gently pull the jammed paper out. 7. After taking out papers jammed, install the laser toner cartridge again and close the front cover, then the printer will recover printing. 11.1.4.
1.Open the rear cover. 2.Open the fuser door using the handles on both sides. 3.Gently pull the jammed paper out. 4. After taking papers jammed out, close the back cover and open the front cover and then the printer will recover printing.
11.1.5.Duplex Unit Jam 1.Remove the duplex printing unit from the back of the printer. 2.Remove the jammed paper from the duplex unit. 3.If the paper does not come out along with the duplex unit, open the tray and remove the jammed paper directly from the bottom. 4. After taking papers jammed out, install the duplex unit back and inspect other parts to the product.
• If the printer still does not start printing, please check that all the jammed paper inside the printer has been cleared. • If you cannot remove the jammed paper yourself, please contact your local Pantum authorized repair center or send the printer to the nearest Pantum authorized service center for repair. • Printer appearance may differ because of various models and functions, so the schematic diagram is only for your reference. 11.2.
Driver program of printer is not installed correctly. Please eliminate errors so that the printer can recover to its normal state. Unload and reinstall the driver program of printer. Problems with Paper Handling Paper feed failure The print media has been loaded incorrectly. The print media is out of the supported media range. Please install printing medium correctly; please print with manual feed tray if special printing medium is used to print. The feed roller is dirty.
• Toner cartridge is damaged. Toner spots • The print media does not meet the usage specifications, for example the media is damp or too rough, or has been used previously. • Please use the print media within the specification range. • Clean the paper path. • The paper path is dirty. • The print media does not meet the usage specifications, for example the media is damp or too rough, or has been used previously. • The paper path is dirty.
Skewed pages Wrinkled paper • The print media has been loaded incorrectly. • Ensure the correct loading of the print media. • The print media does not meet the usage specifications. • Please use print media within the specification range. • The paper path of the printer is dirty. • Clean the paper path inside the printer. • The fuser component is damaged. • Please contact customer services center to replace to a new fuser assembly.
12.Menu Structure This chapter mainly introduces the overall menu structure of control panel. The user can know the menu options which can be set by checking the menu structure. Note: • The menu structure in this chapter is the most complete menu structure. Differences might be existed between the menu structure of the mode you actually use with the following menu structure. General Menu Structure First-level Menu Second-level Menu Third-level Menu 1.中文* 2.English 3.Italiano ɪɭɫɫɤɢɣ 5.
5. 60min 1.Turn off 3.Toner Save 2.Turn on 1.Turn off 4.Mute printing 2.Turn on 1.No 5.Restore Set 2.Yes 1.Paper Size 1.Man.FeedTray 2.Paper type 1.Paper Size 2.Tray Setup 2.AutoInp.Tray 2.Paper type 1.Turn off 3.Load paper tip 2.Turn on 1.IPv4 1.Wired Config 2.IPv6 1.Wireless NetW 2.WPS 2.Wireless Conf 3.Network Set 3.IPv4 4.IPv6 1.Turn off 3.Wi-Fi dir. 2.Auto 3.
1.IP Address 1.Wired Info 2.Subnet mask 3.Gateway 1.Connect state 2.IP Address 3.Subnet mask 2.Wireless Info 4.Gateway 4.Network Info 5.Channel 6.SSID 1.Status 2.Device name 3. Wi-Fi dir. Info 3.IP Address 4.Password 5.Cnnected device 1.Demo Page 2.Info Page 3.Menu Struc Pg 4.NetConf Pg 5.Prt Info Rept 5.Wi-Fi Hots Page 6.PCL Font Page 7.PS Font Page 8.
1.Data FW ver. 6.Version Info 2.Engine FW ver. 7.
13.Product Specifications Note: • Specification values vary slightly from printers with different models with different functions ,and product specifications vary from different countries and regions. • These values are based on the initial data. For more information about the latest specifications, please visit: www.pantum.com. 13.1.Overview of the Specifications Product Size(W*D*H) 333mm*355mm*215mm Product Weight 6.
Linux (Ubuntu 12.04/ Ubuntu 14.04) Operating system Versions higher than IOS 6.0 (excluding IOS 6.0) Android 4.0 and higher versions NeoKylin (Loongson V6.0 Build0341050) USB 2.0(High Speed) Communication interface IEEE802.3 10Base-T/100Base-Tx IEEE802.