Pantum M6700/M6800 Series Pantum M7100/M7200 Series Monochrome Laser Multifunction Printer It is recommended that you read this Guide carefully before using the printer
Preface Welcome to the Pantum Series products! We heartily appreciate your using of Pantum Series products! To protect your vital interests, please carefully read the following statements. Legal Notice Trademark Pantum and Pantum logos are registered trademarks of Zhuhai Pantum Electronics Co., Ltd. Microsoft®, Windows®, Windows Server® and Windows Vista® are trademarks registered by Microsoft Corporation in the United States or other countries/regions.
Safety Precautions Disconnect the power supply The product should be placed close to or easily accessible to power sockets, so as to allow easy disconnection of power supply! Laser Safety The laser radiation is harmful to the human body. Since laser components are completely sealed in the printer, laser radiation will not leak. To avoid laser radiation, please do not randomly disassemble the printer! The printer follows the provisions of Class 1 laser products under CFR standard.
Safety Warning Please note the following safety warnings before using the printer: Warning There is high-voltage electrode inside the printer. Before cleaning the printer, make sure the power is turned off! Plugging and unplugging the power cord plug with a wet hand can result in an electric shock. The fuser unit is hot when and after printing. Touching the fuser unit (the shaded area as shown) may cause burns! The fuser unit is attached with a high temperature warning label.
Precautions Precautions before Using the Printer: 1. Read and understand all instructions. 2. Familiarize yourself with the basic principles associated with operating electrical appliances. 3. Comply with all warnings and instructions marked on the equipment or specified in the manual supplied with the equipment. 4. If the operating instructions conflict with the safety information, please refer back to the safety information, as you may have misunderstood the operating instructions.
19. In standby status, the product will automatically enter into the power saving (sleep) mode if it does not receive any job order for a while (such as 1 minute); and it can realize zero power consumption only if it has not been connected with any external input power supply. 20. As the Class 1 equipment, the product must be connected to the power supply outlet with protective grounding line when using. 21.
30. The power consumption of the product with wireless function is 2.8W without wireless function is 2.0W in networked standby if all wired network ports are connected and all wireless network ports are activated. 31. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits. 32. This Class B digital apparatus complies with Canadian ICES-003. 33. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
Legal Information This symbol indicates that, at the end of your product’s life, it must not be discarded as domestic waste. Instead, you should dispose of your used equipment at a designated collection point for the recycling of waste electrical and electronic equipment. Ref: EU Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). Please contact your distributor / supplier for further information. This product is suitable for indoor use only.
Table of Contents 1. Before Using the Printer .......................................................................................................... 1 1.1. Product series introduction ............................................................................................ 1 1.2. Supplied Accessories .................................................................................................... 2 1.3. Product View ..................................................................................
5.2.3. How to disable the Wi-Fi Direct ......................................................................... 52 5.3. Wireless network setup FAQs ..................................................................................... 53 6. Web server ........................................................................................................................... 54 6.1. Visit the embedded Web server .................................................................................. 54 6.2.
9.1.1. Pantum Scan Application .................................................................................. 79 9.1.2. TWAIN Scan Driver ........................................................................................... 80 9.1.3. WIA Scan Driver ............................................................................................... 82 9.2. macOS System Scan .................................................................................................. 87 9.2.1. ICA Scan.............
.1.6. Print a Page for Clean & Fix .......................................................................... 107 12.1.7. Auto shut-off setting ...................................................................................... 107 12.1.8. Sound/volume (applicable to machine with the fax feature) ........................... 108 12.1.9. Time/date (applicable to machine with the fax feature) .................................. 108 12.2. Network Settings ....................................................
1. Before Using the Printer 1.1.
Note：• This product series is subject to additions or changes without prior notice. • For machine with the fax feature, it needs to execute language, system and fax settings following instructions on the panel in first startup or after restoring to factory settings. • For this user manual, the "ADF" is short for automatic document feeder. 1.2.
1.3. Product View Side view 1 2 3 Cover of automatic document feeder Feed tray of automatic document feeder Exit tray of automatic document feeder 4 Cover of scanner 5 6 7 9 10 11 12 Output Bin Front USB interface Control Panel NFC (Near Field Communication) label Glass Platen Output Tray Front Cover Manual feed tray 13 Power switch 14 Automatic Feeder Tray 8 This is used to remove the paper jammed in scanning for the ADF. This is used to place originals scanned from the ADF.
15 16 17 18 Paper deflector of manual feed tray Paper width deflector of auto feed tray Paper length deflector of auto feed tray Clip of extended tray of auto feed tray Slide paper deflector to adapt to paper width Slide paper width deflector to adapt to paper width. Slide paper length deflector to adapt to paper length. For adjustment of length extension of the tray . Rear View 1 LINE interface (only for machine Telephone line interface, used for connection of this product to with the fax feature.
1.4. Laser Toner Cartridge Laser toner cartridge is composed of drum component and toner cartridge.
1.5. Control Panel 1.5.1. Overview of control panel The layout of the printer control panel is shown below: Control panel without the fax feature 1 LCD Display Display operation interface and product information. 2 Copy Button Press this button to enter into copy mode. 3 Scan Button Press this button to enter into scan mode. 4 ID Card Copy Button Press this button to enter into ID Card Copy mode.
10 Back Return to the previous menu. 11 OK Confirm the selection on screen. 12 UP Scroll through the menus and options . Increase 1 copy on the ready interface of Copy mode. 13 Down Scroll through the menus and options . Decrease 1 copy on the ready interface of Copy mode. 14 Status Light Indicate the status of printer. (Please see Chapter 1.6). Control panel with the fax feature No. Name Functions 1 LCD Display Display operation interface and product information.
8 Redial/Pause This is used to redial the last number dialed before under Standby mode or to insert a pause symbol in the fax number under Edit mode. 9 Bill Copy Button Press this button to enter into Bill Copy mode. 10 Wi-Fi button Short press Wi-Fi button to turn on direct Wi-Fi connection of the printer and automatically print out "Mobile Device Wi-Fi Connection Wizard" page (for models with Wi-Fi function only).
1.5.2. Function of numeric keyboard Sometimes it needs to input names and numbers in executing some tasks. Letters, numbers and characters on the keyboard are distributed as below: Keys Numbers, letters and characters distributed 0 0 1 @ 2 / ; .
1.6. Function of status indicator The meanings of status displayed by the status indicator are as below: No.
2. Paper and Print Media 2.1.
2.2. Special Paper This printer supports using the special paper for printing. Special paper includes: label paper,envelope, transparent film, thick paper,carton paper, thin paper. Note：• When using special paper or print media, be sure to select matched print type and size in the print settings so as to get the best print effect. Please observe the following standards: Types of Print Media Correct Practices Incorrect Practices Label Paper Use labels with no exposed lining paper only.
2.3. Non-printing Area and Non-scanning Area The shaded part indicates the non-printing area and non-scanning area. Usage Printing Scan Paper Size Top and bottom margins (A) Left and right margins (B) A4 5mm(0.197inch) 5mm(0.197inch) Letter 5mm(0.197inch) 5mm(0.197inch) A4 5mm(0.197inch) 5mm(0.197inch) Letter 5mm(0.197inch) 5mm(0.197inch) 2.4. Loading Paper Note：• Printer appearance may differ because of various models and functions, so the schematic diagram is only for your reference. 2.
2. Slide the clip of extended tray of auto feed tray, paper length deflector and paper width deflector to the slot suitable for paper size, in order to match paper length and width. Note：• Do not overly squeeze the "paper length guide" and "paper width guide", otherwise it could easily lead to deformation of paper. 3. Before loading paper, please unfold the stacked paper to avoid a paper jam or feed error, and then load the paper into the tray print-side down.
Note：• It is recommended that you raise the output tray to prevent the paper from slipping and falling after printing. If you choose not to raise the output tray, we recommend that you immediately remove the printed paper from the printer. • If more than 250 pages (80 g/m²) are put inside the auto feed tray at one time, paper jam or paper feed failure will be led to. • If carrying out single-sided printing, please make sure that the side to be printed (the blank side) is face down. 2.4.2.
3. Slide the paper deflector of manual feed tray to match the two sides of paper. Do not use excessive force; otherwise, paper will be made jammed or skewed. 4. Put a flat printing medium into the manual feed tray with both hands. Note：• The printer will enter manual feed mode automatically when you put papers inside the manual feed tray. • Please put one printing medium inside the manual feed tray each time and put in another piece after finishing printing.
Note：• After printing, please take out printed papers output from printer immediately. Stacked papers or envelops will lead to paper jam or wrapped paper. 2.5. Paper and Manuscript Use Process Manuscript requirements: Source Type Size Automatic document feeder (ADF) Plain paper A4, A5, B5, A6,Letter,Folio,Legal Platen Plain paper, thin paper, thick paper, A4, A5, B5, Letter, Full Scanning transparent film, carton paper, label paper, Platen, Custom envelope 2.5.1.
2. Load the manuscript face down. 3. Align the manuscript to match the appropriate paper size. Note：• If the manuscript does not match with any size marker, please align the upper-left corner of the manuscript with the arrow. • Make sure there is no document in the ADF. If a document is detected in the ADF, it will be more preferential than that on glass platen 4. Close the scanner cover gently.
Note：• Please put the paper or document on the scanner glass after the glue, ink or correction fluid are completely dried. • Rough textured, uneven, oil stained and extremely smooth paper will make printing effect poor. • Please make sure that there is no dust, fluff, etc. on the paper. • Paper shall be put on a flat surface and stored under a cool and dry environment. • To avoid influencing the definition, please don't open the scanner cover during scanning with the platen. 2.5.2.
3. Driver installation and uninstallation 3.1. How to install Windows printer driver Windows driver installation software provides two installing methods: one-click installation and manual installation.We recommend one-click installation, which can help to install driver automatically in a faster and more convenient way.If you have any difficulty in using one-click installation, please try manual installation.
4. Click on the "One-click installation" button in Method I and enter into the installation process. The process may need some time, and the duration is related to your computer configuration, please wait patiently. 5. After the installation, click "Print &Test Page" button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.1.2. Method II: Connect the printer via wired network (applicable to wired network models) 1.
• Windows 8 system: When the " DVD RW driver" window pops up from the right top corner of computer desktop, click anywhere in the pop-up window, then click "Autorun.exe" to run the installation procedure. • Windows 10 system: When the "DVD RW driver" window pops up from the right top corner of computer desktop, click anywhere in the window, then click "Autorun.exe" to run the installation procedure. Note:• Some computers may be unable to auto play the CD beacase of system configuration.
• If your software has searched several printers, click on the"One-click intallation" button, and the printer list interface will pop up. Please select the printer that you need according to your printer wired network IP address or host ID.
Note:• If the printer you need is not shown in the list, please click "Refresh" button to search again. If it is not found, please check if the printer and computer are in the same network. (Please see Chapter 5.3 for how to check). • When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver. If you need to install the printer driver with the host ID, please check the option "Install the printer in the list with host ID".
4. Read and agree to the terms contained in the End User License Agreement and the Privacy Policy, click the “Next” button in the lower right corner of the interface to enter the driver installation interface. 5. Click the "One-click installation" button in Method III to install driver software.
• If your software has searched several printers, click "One-click intallation" button, and the printer list interface will pop up. Please select "Configure printer with Wi-Fi via USB and install" and select USB printer, click "Confirm" button and enter into installation process to complete automatic network configuration and driver installation. Note:• When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver.
• Windows 8 system: When the " DVD RW driver" window pops up from the right top corner of computer desktop, click anywhere in the pop-up window, then click "Autorun.exe" to run the installation procedure. • Windows 10 system: When the "DVD RW driver" window pops up from the right top corner of computer desktop, click anywhere in the window, then click "Autorun.exe" to run the installation procedure. Note:• Some computers may be unable to auto play the CD beacase of system configuration.
• If your software has searched more than one printers, the printer list interface will pop up.You need to configure the current printer which is connected via USB cable to wireless network and install driver. Please select "Configure the print via USB and install" on the printer list interface and check the USB printer option. Click the "Confirm" button, and the wireless network configuration interface will pop up.
Note:• When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver. If you need to install the printer driver with the host ID, please check the option "Install the printer in the list with host ID". 6. After the installation, click "Print &Test Page" button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.1.3.1.2.
4. Read and agree to the terms contained in the End User License Agreement and the Privacy Policy, click the “Next” button in the lower right corner of the interface to enter the driver installation interface. 5. Click on the "One-click installation" button in Method III, and enter into installation process. The process may need some time, and the duration is related to your computer configuration, please wait patiently. 6. After the installation, click "Print &Test Page" button.
• Windows 8 system: When the " DVD RW driver" window pops up from the right top corner of computer desktop, click anywhere in the pop-up window, then click "Autorun.exe" to run the installation procedure. • Windows 10 system: When the "DVD RW driver" window pops up from the right top corner of computer desktop, click anywhere in the window, then click "Autorun.exe" to run the installation procedure. Note:• Some computers may be unable to auto play the CD beacase of system configuration.
• If the software has searched several printers, the printer list interface will pop up. Please select the printer you need according to your printer wired network IP address or host ID .
Note:• If the printer you need is not shown in the list, please click "Refresh" button to search again. If it is not found, please check if the printer and computer are in the same network. (Please see Chapter 5.3 for how to check). • When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver. If you need to install the printer driver with the host ID, please check the option "Install the printer in the list with host ID".
6. Select "Connect via USB" and click on "Install". 7. The software installs the driver automatically and the installation process may need some time. The duration is related to your computer configuration, please wait patiently. 8. After the installation, click "Print &Test Page" button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.2.2. Installation via wired network connection (applicable to wired network models) 1.
6. Click on the "Manual installation" at the bottom of driver installation interface, and enter into manual intallation interface. 7. Please select installation language and printer model. 8. Select "Wireline network connection" and click on "Install". 9. The installation software will search the printer automatically and the searching process may need some time. 10. After finishing searching, select the printer that needs to be connected and click “Next”.
11. The software installs the driver automatically and the installation process may need some time. The duration is related to your computer configuration, please wait patiently. 12. After the installation, click "Print &Test Page" button. If your printer prints the test page successfully, it means that you have installed the driver correctly. 3.1.2.3.
7. Select "Wireless network connection" and click on "Install". 8. Select “Yes, I want to configurate the printer's wireless network” on the wireless setup window popped out, and operate according to the prompts to set up the printer to wireless network (please refer to Chapter 5.1.1 for setup method).
9. The installation software will search the printer automatically after wireless network is configured successfully. The search process may need some time. 10. Select the printer needs to be connected and click “Next”. Note:• If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again. • When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver.
Note:• Some computers may be unable to auto play the CD beacase of system configuration. Please double click "Computer" icon, find "DVD RW driver", then double click "DVD RW driver" to run the installation procedure. 4. Read and agree to the terms contained in the End User License Agreement and the Privacy Policy, click the “Next” button in the lower right corner of the interface to enter the driver installation interface. 5.
10. Select the printer needs to be connected and click “Next”. Note:• If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again. • When the printer IP address changes under printer driver installed with host ID , you can also directly print without re-installing the driver. If you need to install the printer driver with the host ID, please check the option "Install the printer in the list with host ID".
3.2. macOS system driver installation • Driver installation under macOS system is divided into 2 steps, driver installation and adding a printer. If you are going to print in AirPrint mode, there is no need to install a driver and you just need to add a printer directly. • When you are installing a driver with wired or wireless network, you may need to know the Bonjour name of printer. Please print the “Network setup page” to view it. (Please refer to Chapter 12.4). 3.2.1. Driver installation macOS 10.
5. Click “Agree” on the prompt window popping out to accept the licensing agreement. 6. Read the Privacy Policy and press "Continue". 7. In the popped-up prompt window, press "Agree" to accept the Privacy Policy. 8. Click “Install”. 9. Input computer password and click “Install Software”. 10. Click “Continue Installation” on the prompt window popping out. 11. The system will finish driver installation automatically.
• If using a USB cable to connect a computer with a Wi-Fi model printer, a wireless network configuration prompt window will pop up during driver installation, as shown in following picture. Note: • Click “Yes”, you can configure printer’s wireless network via wireless network configuration tool (refer to Chapter 5.1.1 for how to make configuration).
3.3.3. Add up the printer via wireless connection(applicable to Wi-Fi models) 1. Turn the power of printer and computer on. 2. Make sure the wireless network connection between computer and printer is set up. Note：• In case of basic structure mode, connect wireless network printer to the access point (wireless router). Please refer to Chapter 5.1 for connection method. • In case of Wi-Fi Direct mode, connect wireless client to wireless network printer directly. Please refer to Chapter 5.
4. Wired network setup (applicable to wired network models) In case printers support wired network printing, they can be connected to network to control printer to print in wired network mode. 4.1. Set IP Address The IP address of the printer may be automatically obtained through DHCP function or set manually. 4.1.1. Automatic Setting DHCP automatic setting function is enabled by default on the printer. 1.
5. Wireless network setup (applicable to Wi-Fi models) Wireless network connection type is divided into basic structure mode and Wi-Fi Direct mode. If you have problems with wireless network setup, please refer to Chapter 5.3 Wireless Network Setup FAQs. Basic structure mode: connecting to a wireless device via router 1. Access point (wireless router) 2. Wireless network printer 3. Computer connecting to access point via wireless network 4.
5.1.1.2. Setup methods of wireless network setup tools 1. Take the wireless network setup tool in computer. 1) Windows system: Click the “Start menu” – “All programs” - “Pantum”－ Product name – “Wireless network setup tool”. 2) macOS system: click "Go" - "Applications" - "Pantum" - "Utilities" - "Wireless Network Configuration Tool" on the computer Finder menu bar. 2. Use USB cable to connect and configure. Select "Yes, I have an USB cable that can be used for installation" in the following interface.
2) Please tick “No” to configure other wireless network needed to connect to. Complete configuration according to interface prompt. Note：• The display password is not ticked by default; if it is ticked, all passwords input can be seen in clear text. • Some models can automatically match the encryption method, no manual selection is required. 2.2 The computer is not connected to wireless network Input the SSID (case sensitive) and password of access point (wireless router) in the interface below.
3. Use WPS connection. Select “No, I don't have a USB cable” in the interface below and then click “Next”. 1)Use WPS method to perform steps below to start wireless network on printer. (Please refer to Chapter 5.1.
2) Judge if the printer is successfully connected according to the status of Wi-Fi indicator on printer. If configuration failed, please click “Previous” to configure again; if configuration succeeded, please click “Done” to complete configuration. Note：• If the printer cannot be used normally after wireless network setup is finished, please install the drive again. 5.1.2.
Note：• Please refer to Chapter 1.5 for how to cancel and disconnect Wi-Fi connection. • After successful Wi-Fi Protected Setup (WPS) connection, please install a driver if you want to print via wireless network. 5.1.3. How to disable the Wi-Fi network connected Connect the wireless network in infrastructure mode by the steps above. If connected, the Wi-Fi light on the control panel is normally on. Press and hold this button for more than 2s to disconnect from Wi-Fi network (Wi-Fi light will be off). 5.2.
3. Select “Advanced” and then select “Wi-Fi Direct” in advanced WLAN interface. 4. Select printer SSID on direct interface to launch a connection invitation. 5. Press “OK key” to confirm connection when the panel lead to prompts whether to connect to start Wi-Fi Direct connection. Note：• In case of auto connection mode, the mobile device will start to connect automatically after initiating connection invitation without panel confirmation. 5.2.2.2.
5.3. Wireless network setup FAQs 1. The printer is not found. • If the power of computer, access point (wireless router) or printer is turned on. • If the computer is connected to printer with USB cable. • If the printer supports wireless network connection. 2. SSID cannot be found when network is connected • Inspect if the power switch of access point (wireless router) is turned on.
6. Web server You can manage printer setup via the embedded Web server. 6.1. Visit the embedded Web server 1. Turn on the power of printer and computer. 2. Connect the printer to network to ensure that the printer is connected to the network where the computer is connected to (please refer to Chapter 4 or Chapter 5 for network setup method). 3. Input the IP address of printer in the address bar of Web browser to visit the Web server imbedded in printer.
6.2. Use Web server to manage printer You can use the embedded Web server to manage printer. 1. View the basic information including product name, printer state and ink cartridge of printer. 2. Set up the network protocol parameters supported by printer. 3. Set up the wireless network connection of printer, and turn on/off wireless network and Wi-Fi Direct function. 4. Set up mail server client and acquire printer state via E-mail notification. 5.
6.2.1.2. IPv6 setup 1. Turn on printer power to connect printer to network. 2. Log in the embedded Web server (please refer to Chapter 6.1 for login method). 3. Click “Settings” – “Network settings” – “Protocol Settings” – “IPv6”. 4. Tick “Enable IPv6 protocol” and “Enable DHCPv6” (ticked by default) and then click “Apply”. You can refresh the browser and view the “IPv6 Local Link Address” and “Stateful Address” in “Wired IP Configuration” interface.
6.2.3. Machine setup You can add mail address contacts, set up e-mail notification, set up sleep time and recover factory settings via machine setup page. 6.2.3.1. Set up e-mail notification If you set up e-mail notification, an e-mail will be sent to the mail address specified by you when abnormality such as paper out occurs. You can receive emails only if you made correct email setup. Please consult your network administrator for detailed setup steps.
II. Set the e-mail group 1. Log in the embedded Web server (please refer to Chapter 6.1 for login method). 2. Click “Settings”, “Machine Settings” and then “E-mail Group” to enter the setting interface of e-mail group. 3. Click “Create” to pop out a window as below and edit the group name and check the e-mail address to be added in the contact name (e-mail address) listbox, and then click "Apply". 6.2.3.3.
3. Click "Create" to pop out a window as below and set relevant parameters; after settings completed, and then click "Apply". 6.2.3.4. Sleep time setup 1. Log in the embedded Web server (please refer to Chapter 6.1 for login method). 2. Click “Settings” – “Machine settings” – “System”. 3. Select sleep time according to you need and then click “Apply”. 6.2.4. Recover factory settings via Web server 1. Log in the embedded Web server (please refer to Chapter 6.1 for login method). 2.
7. Print 7.1. Print Function You can set the print function through "Start"-"Devices and Printers"- select corresponding printerright click – set print function in "Printing preferences". Some functions are as follows: Functions Diagram Automatic Two-Sided Printing Collate Print Reverse Print N-in-1 Poster Print(for Windows Operation System only) Zoom Print Custom Size Note：• Windows 7 is taken as example in the above description.
7.2. Print Settings You can set up printing parameters with the following two methods before sending printing work (such as paper type, paper size and paper source). Operating system Temporary printing setup change Permanent default setup change Windows 7 1. Click “File” menu – “Print” – “Select printer" - “Printer properties” (the detailed steps may differ because of multiple operating systems). 1. Click “Start” menu- “Control Panel” – “Devices and Printers”. 2.
Note：• For precautions on loading paper, see Chapter 2. • For the type of media to be printed with the automatic feeder tray, see Chapter 2.1. 7.4.2. Printing with manual feed tray When you put papers in the manual feed tray, the printer will enter manual feed mode. Note：• Manual feed mode means that papers will be fed from the manual feed tray first if there are papers being put inside it. • Generally, the manual feeder tray is used to print on special paper, such as envelopes, transparencies, etc.
7.5.1. Duplex printing unit setup For the purpose of achieving the best printing result, you can set up the paper size of duplex printing unit. As for duplex printing of A4 and 16K papers, the slide should be adjusted to the A4 position; as for Letter, Legal, Folio and Oficio duplex printing, the slide should be adjusted to the Letter position. Setup steps of duplex unit are: 1. Draw out duplex unit. 2. Make the backside of duplex unit up. 3.
4. Install the duplex unit in the printer. 7.5.2. How to carry out auto duplex printing 1. Open the print job to be printed from the application (such as a Notepad). 2. Select Print from the File menu.
3. Select printer of the corresponding model. 4. Single click “Preferences” for printing setup. 5. Select the “Duplex” in “Basic” tab and then select “Long Edge” or “Short Edge”.
6. Single click “OK” to finish printing setup. Click “Print” to realize auto duplex printing. 7.6. Fine mode printing The Fine mode is applicable to engineering drawings and fine lines printing. Set up fine mode in the basic page of printer preference . After setup, fine printing mode can be realized.
7.7. Mute printing If the Mute Printing is set, the printing noise will be reduced but the printing will slow down to some extent. The operating steps of mute printing are as follows (applicable to printers that are installed via USB connection) Windows 7 is taken as the example in the following operation. The information on your computer screen may differ because of multiple operating systems. 1. Enter the “Start menu” – “Control Panel” –view “Devices and Printers”. 2.
7.8. Auto shut-off setting “Auto shut-off setting” to set off condition and off delay of printer. 1. Enter computer “Start Menu” – “Control Panel” – View “Devices and Printers”. 2. Right click printer, select “Printer properties” in drop-down list. 3. Enter “Secondary Settings” option and set “Auto shu-off setting”. 4. Click “OK” to finish setting. Note：• For printer provided with LCD control panel, users may set auto off function through control panel keys. Please refer to Chapter 12.1.7.
7.9. Open Help Document You can open the "Printing preferences" and click "Help" button (for Windows Operation System only). The help document contains the user guide where you can find the information on print settings.
8. Copying 8.1. Copying function Copy Instructions Multipage Print a multi-page document to a piece of paper. Clone Print several identical images to a piece of paper. Poster Print a one-page original to pieces of paper. Collated copy Collate copies of an original. Duplex copying It supports manual duplex copying for originals. Image quality Set the definition mode to improve the copying effect. Intensity Adjust deep-light copying effect by setting intensity.
3. Press “direction key to select option to be set and press “OK key” to set option. Note：• The image quality, intensity, resizing and paper setting can keep valid after options are set. • Settings on all-in-one, clone, poster, collated copy and duplex copy will be restored to defaults after completing the copying, switching among panel keys or rebooting the machine. 8.4.1. Image quality Select corresponding image quality mode for original document used in order to improve copying effect.
8.4.4. Multipage With setting on all-in-one feature, a 2- or 4-page document could be copied to one piece of paper. Copying with the ADF and the glass platen are both supported. The multipage includes 3 modes: (1) Two-in-one: (2) Horizontal four-in-one: (3)vertical four-in-one: Note：• "Multipage” and “resizing function” cannot be set at the same time. 8.4.5. Clone Through setting on clone feature, you may print multiple original images on one piece of paper.
8.4.6. Poster Poster setting enables the printing of one piece of original document on several pieces of paper. The "Poster" feature supports only copying with the glass platen. The poster copying includes 3 modes: 2x2： 3x3： 4X4： Note：• The “poster” and “resizing function” cannot be set at the same time. 8.4.7. Collated copy The "Collated Copies" feature supports only copying with the automatic document feeder (ADF).
8.4.8. Manual duplex copying You may use the glass platen or the ADF for duplex copying. The followings are examples of copying with the ADF. There are 4 modes in total for duplex copying: 1. One-sided → One-sided:： 2. One-sided → Two-sided： 3. Two-sided → One-sided： 4.
8.4.8.1. Steps of duplex original copying 1. Put an original into the ADF with its front upward and its top fed first; meanwhile, make sure there are some paper in the carton. 2. Operate following steps described in Chapter 8.4. Select Duplex Copying and then press “OK” to save settings. 3. Press “Start” to begin copying. 4.
5. After completion of copying one side, put the paper into the entrance as shown in figure (without turnover or rotation). Note：• If the turnover prompt on panel times out, the machine will execute one-sided copying automatically. 6. Press "Start" to begin copying the other side. 8.4.9. Paper setting Select the paper size and paper type of original copying in Paper Settings menu. Paper dimension: A4, Letter, B5, A5, A6, Executive, Legal and Folio.
8.5.1. Arrangement mode There are 4 arrange modes for ID card copying totally: Whole page up-down Half page up-down Half page left-right A5 left and right Position: Half page up-down: default mode; put ID card at “orange left half area” of glass platform. Half-page up and down, half-page left and right or A5 left and right: put the ID card in the "blue area" in glass platen.
8.6. Receipt setting For better copying effect of bills, you can enter the "Bill Copy Setting" menu to change relevant settings. 1. Press "Bill Copy" and then "Menu" on control panel to enter the "Menu Settings" interface. 2. Press "OK" to enter the "Bill Copy Setting" interface. 3. Press “direction key to select option to be set and press “OK key” to set option. 8.6.1. Intensity For intensity setting, see 8.4.2. 8.6.2.
9. Scan This printer provides two types of scan: "Push Scan", which means scanning through the printer’s Control Panel operations; "Pull Scan" which means scanning through PC terminal scanning the application. Before scanning, please be sure a printer driver has been installed in the computer. 9.1. Pull Scan You may scan with the scanning application in PC via USB, wired or wireless connection. Please be sure the printer has been properly connected before scanning. 9.1.1.
This product complies with the TWAIN and Windows Image Application (WIA) standard. If using the application which supports TWAIN and WIA standard, users can use the scan function and directly scan the images to the open application. The handbook requires Office Software (Word and Excel) and Photoshop ,for example, to show the operation. 9.1.2. TWAIN Scan Driver 9.1.2.1. Office Software (Word and Excel) Operation Steps: 1. Open the Office software (Word or Excel). 2.
4. After the window pops up, set the scan information in the right list of "Basic Setting" and "Advanced Setting". Click on "Scan" and start scan.
9.1.2.2. Photoshop Operation Steps: 1. Launch Photoshop, click on "File" – "Import" on the top left corner and select TWAIN Scan, as is shown below: 2. After the window pops up, please refer to Step 4 of 9.1.2.1 to see the specific operation steps. 9.1.3. WIA Scan Driver 9.1.3.1. WIA1.0 Scan (Windows XP / Windows Server 2003) 1. Office Software (Word and Excel) Operation Steps: 1) Open the Office software (Word or Excel). 2) Keyboard shortcuts: Alt+I+P+S to open the application’s window.
3) Click on "Device" and select WIA Scan,click the “Custom Insert” below. 4) The prompt window as is shown below, set the scan information.
5) Click on "Adjust the Scanned Image Quality" on the bottom left corner of the above picture, the advanced properties interface will pop up, then users can set the scan; After finishing the settings, click on the "OK" button, then "Scan" button to start scan. 2.
2) After the window pops up, please refer to Step 4 and Step 5 of 9.1.3.1 to see the specific operation steps. 9.1.3.2.WIA 2.0 Scan (Windows Vista / Windows Server 2008 and later versions) Operation Steps: 1. Click on "Start"- "All Programs"- "Device and Printer" on the left bottom of the desktop. 2. When the pop-up window appears, select the printer you want to use, and right click the mouse.
3. Click on "Start Scan" in the above option bar. 4. After the window pops up, set the scan and click "Scan" on the bottom right corner and start scan.
9.2. macOS System Scan 9.2.1. ICA Scan 9.2.1.1. Open ICA via "Print and Scan" Operation Steps: 1. After installing the printer driver, click "System Preferences" icon on the bottom left corner of the computer desktop. 2. After the window pops up, click on "Print and Scan".
3. After the window pops up, click on "Scan" 4. Click on "Open Scanner" and the scan window will pop up.
5. Click on "Show Details" on the bottom right corner to set the scan parameters. 6. Click on "Scan" on the bottom right corner and start scan. 9.2.1.2. Call CIA through applications Operation Steps: 1. Click on "Finder" icon on the bottom left corner of the computer desktop, or use keyboard shortcuts command+shift+C to open the window. Find "Image Capture" in "Applications" (or conduct keyboard shortcuts command+shift+A to directly switch to "Applications") and click to launch the application.
2. After selecting the printer in the left list, set the scan parameters in the right list. Click on "Scan" on the bottom right corner and start scan. 9.2.2. TWAIN Scan Take Photoshop as an example. Operation Steps: 1. Launch Photoshop, click on "File" – "Import" on the top left corner and select TWAIN Scan, as is shown below: 2. After the window pops up, please refer to Step 4 of 9.1.2.1 to see the specific operation steps.
9.3. Push Scan This section is mainly to introduce how to scan files to PC, E-mail, FTP and USB with the printer's control panel. Note：• The one-page file scanned to PC, E-mail or FTP could be saved in PDF, TIFF or JPEG; if scanned to USB, it could be saved in PDF and JPEG. • Under merge scan mode, a file scanned to PC or USB will be saved in PDF be default; if scanned to E-mail or FTP, it will be saved in PDF, TIFF or JPEG. 9.3.1.
Set the group name for group e-mail sending by webpage, and set the members, i.e.the receivers, in the group of group email. After finishing scanning, firmware will send the scanned documents to the mail server. Then mail server sends the documents to every member of the group. 9.3.3. Scan to FTP Be sure the user is in an Internet-connected environment in scanning files to FTP server.
10. Fax 10.1. Connect Devices •“ •“ ” port is used to connect fax with telephone line. ” port is used to connect external telephone. Note：• It is recommended to use the traditional analog phone service (PSTN: Public Switched Telephone Network) in connecting telephone line. If a digital environment (for examples, DSL, PBX, ISDN or VoIP) used, please be sure to use a proper filter and configure digital settings correctly. For more information, please contact your digital service provider. 10.2.
3. Choose the Fax option you want to set by pressing the page up and down keys. 4. Here can be a total of 16 settings, set the standard as follows: No. Options Description 1 Resolution You may select the faxing definition from options of “Standard, Fine, Super Fine and Image”. It defaults to “Standard”. 2 Original Size You can select the desired size of the document to be Faxed. The available options are A4, Letter and Legal.
11 Compatibility If Fax is sent or received abnormally due to disturbance on telephone line, try to switch to VOIP compatibility mode. 12 Country / Region To adapt to different telephone lines in different countries, settings on different countries or regions are needed. 13 Fax Report You can use the options in Fax Report to print the Fax report as you need. 14 Active Job Query for the list of all Faxes for Delay sending and you can press the Cancel button to delete a Delay sending job.
5. After all scanning complete, activate the fax to send. Note：• In order to prevent damage to this product, do not use a manuscript with correction tape, correction fluid, paper clips or staples on it. In addition, do not load photos, small manuscripts or brittle manuscripts into the automatic document feeder. 10.3.1.2. Manual fax sending 1. Put an original on the glass platen or into the ADF (please see Chapter 2.5 for how to put an original). 2.
10.3.2.1. Auto receiving under fax mode In receiving the fax, the machine answers the call with the set ring count and then receive the fax automatically. The ring count defaults to 4 times. To change the ring count, please see Chapter 10.2 and Chapter 15. To adjust the ring volume, please see Chapter 12.1.8. 10.3.2.2. Manual receiving under telephone mode Under telephone mode, there are 3 ways to receive a fax when there is a fax call: 1.
4. Receive and forward You can forward the Fax you receive. When you receive a Fax job, it will be stored in memory at first. Then the printer dials the Fax number you have specified and send the Fax. If a fax fails to be forwarded due to busy line or line failure, This printer will print a copy of fax contents to be forwarded for backup. (If the Redial feature is set, it will print after redialing) .
10.4.1.Sending Fax with PC-Fax 1. Open the document to be faxed. 2. Click "File" and then "Print". 3. Select a printer named after the end of Fax and then click "Printer Properties"; next, set "Paper" and "Quality" of PC-Fax sending on the "Fax Settings" popup. 4. Click "Print" to present the "Send Fax" interface. 5.
11. Mobile Print/Scan/Fax 11.1. "Pantum" APP Pantum APP is a free application with mobile printing, scanning and faxing functions, allowing you to print or fax photos, files, pages and scan photos or files directly from mobile terminal. Your printer may not support all of above mentioned functions, so please select relevant function of Pantum APP for use according to your printer type. Please be sure the application has been installed and connected to wireless network properly before use. 11.1.1.
11.1.3.2. For iOS Devices 11.1.3.2.1. Preliminary preparations 1. A printer that has wireless network function. 2.iOS mobile device. 11.1.3.2.2. Operation steps 1. Turn on printer power. 2. For an iOS mobile device, tap the “PANTUM” icon on the main screen to enter the first interface of “PANTUM”. 3. Select the connection method according to your habit to connect the printer. 4. Select the function you need and set it up to meet your function needs.
11.2.4. How to use Mopria mobile printing Before printing, please set the Mopria print service as "ON". 1.Tap the "settings" of the Home Screen on Android mobile device, and select "print". 2.Set the "Mopria print service" as "ON". All other printing plug-ins should be shut down when you use Mopria mobile printing function. The printing steps may varied by applications, taking Adobe Reader as an example for explanation. 1. Turn on printer power. 2.
Note:• For some mobile devices, NFC antenna may not be on their backsides. Before touching, please check the position of the NFC antenna of your mobile device. • If the mobile device is not installed with Pantum App, the Pantum App download link will pop out automatically. Try again after downloading and installing the App. 3. Select the content to be printed and set printing parameters according to needs. 4. Click print and the printer will start to print. 11.4.
12. General Settings This Chapter mainly introduces some general settings. Note：• The panel appearance may be a little different due to difference in type or function. All diagrams are only for reference. 12.1. System Settings 12.1.1. Ink saving setting You can select the save toner mode which can reduce toner consumption and reduce printing cost. When save toner mode is “on”, the printed color will be lighter. Save toner mode is “off” by default. 1. Press "Menu" to enter the menu setting interface. 2.
12.1.2. Language Setting "Language Setting" is used to select the language to be displayed on the control panel. 1. Press "Menu" to enter the menu setting interface. 2. Press "▲" or "▼" to select "System Setting" and then press "OK". 3. Press "▲" or "▼" to select "Language set" and then press "OK" to do language setting. 12.1.3. Restore Factory Settings “Restore factory settings” is used to recover the default settings of printer.
12.1.4. Sleep Time Setting Sleep mode can reduce the energy consumption of printer effectively, and “Sleep time setting” can be made in the idle time before the device enters sleep mode. 1. Press "Menu" to enter the menu setting interface. 2. Press "▲" or "▼" to select "System Setting" and then press "OK". 3. Press direction key “▲” or “▼” to select “Sleep time set” option, and press “OK” key to set the corresponding sleep time.
12.1.6. Print a Page for Clean & Fix "Print a Page for Clean & Fix"function can clean the toner, paper powder and other inpurities, so as to realize better printing effect.The printer will start up Print a Page for Clean & Fix function automatically after the printer has printed a certain number of pages. You can also launch Print a Page for Clean & Fix function manually by setting up the printer panel. The steps are as follows: 1. Press "Menu" to enter the Menu Settings interface. 2.
12.1.8. Sound/volume (applicable to machine with the fax feature) You may set the up and down of sound/volume or shut down. 1. Press "Menu" to enter the menu setting interface. 2. Press "▲" or "▼" to select "System Setting" and then press "OK". 3. Press "▲" or "▼" to select "Sound/Volume" and then press "OK" to do settings on "Prompt Tone", "Ring Tone", "Fax Tone" and "Master Volume". 12.1.9. Time/date (applicable to machine with the fax feature) You may set the time and date with the Time/Date option. 1.
12.2. Network Settings You can check or set network status via network setting. 1. Press "Menu" to enter the menu setting interface. 2. Press direction key “▲” or “▼” and select “ Network Set” option. 3. Press “OK” key to set “Network set”, “wireless network setting” and “Wi-Fi Direct”. 12.3. Network Information You can check the network status through Network Information. 1. Press "Menu" to enter the menu setting interface. 2.
12.4. Print information report You can print information report by operating control panel. These pages can help you to learn about product information, and diagnose and solve product failures. 1. Press "Menu" to enter the menu setting interface. 2. Press "▲" or "▼" to select "Info.report". 3. Press “OK” key to enter information report print. You can print product report according to needs.
3. Press "OK" to enter and check the residual amount. 12.6. Configure the e-mail address book (Applicable to machine with the fax feature) 1. Press “Scan” and then “Menu” on control panel to enter the “Menu Setting” interface. 2. Press "OK" to enter the "Scan setting" interface. 3. Press "▲" or "▼" to select “Email Add.” and then press “OK”. 4. Press "▲" or "▼" to select “Add. book edit” and then press “OK” to execute operations of Create, Edit/Check, Delete and Add to Group. 5.
13. Routine Maintenance Note：• Printer appearance may differ because of various models and functions, so the schematic diagram is only for your reference. 13.1. Cleaning the Printer Note：• Please use mild detergents. • Some parts of the printer are still in high temperature within a short time after use. To prevent burns, please don't directly touch places labled with high temperature warning in contact with internal components after opening the printer's front or rear cover. 1.
3. Open the front cover and take the laser toner cartridge out along the track. Note：• When removing the toner cartridge, put the toner cartridge in a protective bag or wrap it with thick paper to avoid direct light damaging the toner cartridge. 4. Clean the inside of the printer by gently wiping the shaded area, as shown in picture, with adry and lint-free cloth. 5. Wipe the LSU lens of printer gently with dry lint cloth.
6. Open the auto feed tray and wipe the pickup roller gently with dry lint cloth. Note：• The machine with the ADF should be regularly cleaned, removing dirt on the top cover of the ADF. Please wipe the place as shown in figure with a soft cloth.
13.2. Toner cartridge and drum component maintenance 13.2.1. About toner cartridge and drum component component 1.Cartridge, use and maintenance of the drum assembly. Please use the original toner cartridge for better printing quality. Please pay attention to the following items while using the toner cartridge: • Please keep the toner cartridge in a dry and dark place.
13.2.2. Replace toner cartridge and drum component Note：Please pay attention to the following matters before replacing toner cartridge: • Since there may be toner on the surface of toner cartridge, please pay attention while taking it out to avoid spattering. • Please place the toner cartridge taken out on paper to avoid large-scale spattering of toner. • When installing, do not touch the surface of the toner cartridge, so as to avoid scratching it. Toner cartridge replacement steps: 1.
3. Press the blue button on the left side of drum component with left hand and lift the toner cartridge handle with right hand at the same time to take the toner cartridge out. 4. Open the package of the new toner cartridge and hold the toner cartridge handle to shake it left and right for 5 – 6 times, so that the toner inside can be uniformly dispersed. 5. Pull the seal out and take the toner protection cover out. 6. Install the drum component along the inner track to finish installing toner cartridge.
7. Take the drum component with toner cartridge installed and install it inside the printer along the inner track of printer to finish installing. 8. Close the front cover. Replace the drum assembly steps are as follows: 1. Power off the printer. 2. Open the front cover and take the laser toner cartridge out along the track.
3. Press the blue button on the left side of drum component with left hand and lift the toner cartridge handle with right hand at the same time to take the toner cartridge out. 4. Open the package of new drum component, take the protection device of drum component, and put the drum component on a horizontal table. 5. Install the drum component along the inner track to finish installing toner cartridge. 6.
14. Troubleshooting Please read this section carefully. It may help you to solve common problems encountered during the printing process. If the problems persist, please contact Pantum Aftersales Service Centre. Prior to handling common problems, first check that: • The power cord is connected correctly and the printer is powered on. • All of the protective parts are removed. • The toner cartridge is installed correctly. • The paper is correctly loaded into the tray.
2. Gently pull the jammed paper out. 3. Install paper tray.
4. Open the front cover. 5. Take the laser toner cartridge out along the track. (For the purpose of preventing printing quality from affecting by the exposure of photosensitive drum, please put the laser toner cartridge inside the protection bag or warp it with thick paper).
6. Gently pull the jammed paper out. 7. After taking out papers jammed, install the laser toner cartridge again and close the front cover, then the printer will recover printing. 14.1.2.
1. Open the front cover and then remove the laser toner cartridge along the guide rail. 2. Open the rear cover. 3. Open the fuser door using the handles on both sides.
4. Gently pull the jammed paper out. 5. Close the back cover after removing the paper jammed. 6. Install a new toner cartridge and then close the front cover; then, the printer will recover printing automatically.
14.1.3. Duplex Unit Jam 1. Remove the duplex printing unit from the back of the printer. 2. Remove the jammed paper from the duplex unit. 3. If the paper does not come out along with the duplex unit, open the tray and remove the jammed paper directly from the bottom. 4. After taking papers jammed out, install the duplex unit back and inspect other parts to the product.
printer will recover printing automatically. Note：• After all papers jammed are taken out according to the above steps, close the front cover and tidy the papers in paper tray, then the printer will recover to print automatically. • If the printer still does not start printing, please check that all the jammed paper inside the printer has been cleared.
2. Remove the paper jammed from the ADF. 3. After removing the paper jamed, close the top cover and then the printer will be back to the ready state.
4. If it is difficult to remove the paper jammed, please try to open the scanner cover and remove it from the pressing block. 14.2. Software Failure Problem Solution The printer icon will not be displayed in the “Device and Printer” folder. Reinstall the printer driver. Ensure that the USB interface cable and the The printer is in Ready mode but it will not perform any print job. If the failure still exists after restarting the Make sure the network cable of USB cable is connected correctly.
14.3. Error Message Error Message Cause Measure No Laser Toner Cartridge Detected The laser toner cartridge is installed incorrectly or laser toner cartridge is damaged. The laser toner cartridge is installed correctly or new laser toner cartridge is replaced. Toner Low (this prompt is displayed together with the standby picture alternately.) The toner in cartridge runs low. Please replace with a new toner cartridge.
14.4. Common Troubleshooting 14.4.1. Common Trouble Trouble Type Fault phenomenon Cause Solution Problems in printing Poor print quality See 14.4.2 Image Defects. See 14.4.2 Image Defects. Failed to copy The scanner is damaged. Please contact Pantum Customer Service. • The scanner is dirty or defective. • The toner cartridge is dirty or damaged. • Clean the scanner. • It is suggested to replace the original toner cartridge.
Paper feed failure Problems with Paper Handling Paper Jam Print multipage feed • Please install printing medium correctly; please print with manual feed tray if special • The printer paper isn't put printing medium is used to print. properly. • Please use the print media • The print media is beyond the within the specification range. usage specification range. • Please clean the pickup roller. • The pickup roller is dirty. Take the excessive papers out Too many papers in paper tray.
14.4.2. Image Defects Problem The printout is whitish or light Toner spots White spots Toner comes off Black vertical stripes Cause Solution • The print media does not meet the usage specifications, for example the media is damp or too rough. • The resolution in the print program is set too low, concentration setting is too low, or toner saving mode is ticked. • Toner cartridge is damaged. • Toner is low. • Please use proper print media within the specification range.
• The scanner is damaged. Black background(gray background) • The print media that does not meet usage specification is used. For example, the media is damp or too rough. • Dirty toner cartridge • Damaged inner parts of toner cartridge. • The paper path is dirty. • The transfer voltage inside the printer is abnormal. • Scanning exposure. • If black background or gray background appears when copying and scanning, the platen glass may be dirty. • Please use the print media within the specification range.
printout is dirty Whole page dark The toner does not adhere to the paper • Toner cartridge is improperly installed. • Inner damage of toner cartridge. • Abnormal internal charging of machine or the toner cartridge is not charged. • If all-black image appear when copying and scanning, maybe it is scanning exposure, and the cover on the manuscript is not properly closed. • The scanner is damaged. • Install ink cartridge correctly. • It is suggested to replace the original toner cartridge.
14.5. Fax faults Trouble Type Fault phenomenon Solution • If you cannot hear the dialing tone after picking up the receiver, please check the connection of all telephone lines between the fax and the wall-mounted The dialing tone cannot be heard. socket. Telephone • Use the telephone connecting another line to test line or the wall-mounted socket; if there is no dialing tone, connection please check the communication line. fault The printer cannot response in a fax call automatically.
files could work normally. • Transmit with a higher resolution. • The telephone line may suffer from temporary noise or electrostatic interference. Please send the fax again. A prompt of "Communication • Please try to set as VoIP in compatibility and then Failure" appears in printing the fax send again. (Please see Chapter 10.3.3 for confirmation report compatibility setting.) If the problem still occurs, please check the telephone line.
15. Menu Structure With the help of menu structure of this printer on the panel menu, you may know and set various functions. The steps of printing are as follows: 1. Press "Menu" to enter the menu setting interface. 2. Press "▲" or "▼" to select "Information Report". 3. Press "OK" and then "▲" or "▼" to select "Print Menu Structure". 4. Press "OK" to print.
16. Product Specifications Note：• Specification values vary slightly from printers with different models with different functions ,and product specifications vary from different countries and regions. • These values are based on the initial data. For more information about the latest specifications, please visit: www.pantum.com. 16.1.
16.2. Print Specifications Print Speed Please see Chapter 1.1. Print Time of First Page Print Language ≤8.5sec Please see Chapter 1.1. 16.3. Copy Specifications Copy Speed FCOT 30cpm(A4)/33cpm(Letter) Flatbed <10 seconds ADF <12 seconds Maximum Pages for Successive Print 99 pages Zoom Ratio Other Copy Functions 25%~400% "ID copy, Receipt copy, N-up copy, Clone copy" 16.4.
Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Unique Identifier Trade Name: PANTUM Model No.: M6/M7******(suffix *: A-Z, 0-9, hyphen or blank) Responsible Party – U.S. Contact Information Company Name: PANTUM (USA) CO.,LTD Office address:13875 Ramona Ave.,Chino, CA 91710 TEL: 626-965-6662 FCC Compliance Statement This device complies with Part 15 of the FCC Rules.
142
