User Guide Pantum M6700/06800 Series Pantum M7100/07200 Series Monochrome Laser MFP It is recommended that you read this Guide carefully before using the printer
Preface Welcome to the Pantum Series products! We heartily appreciate your using of Pantum Series products! To protect your vital interests, please carefully read the following statements. Legal Notice Trademark Pantum and Pantum logos are registered trademarks of Zhuhai Pantum Electronics Co.,Ltd. Microsoft® , Windows® , Windows Server ® and Windows Vista® are trademarks registered by Microsoft Corporation in the United States or other countries/regions.
Safety Precautions Laser Safety The laser radiation is harmful to the human body. Since laser components are completely sealed in the printer, laser radiation will not leak. To avoid laser radiation, please do not randomly disassemble the printer! The printer follows the provisions of Class 1 laser products under CFR standard. The printer has a Class III b laser diode, which has no laser radiation leakage among laser components. The laser components shall complies with the requirements of: U.S.
Precautions Precautions before Using the Printer: 1.Read and understand all instructions. 2.Familiarize yourself with the basic principles associated with operating electrical appliances. 3.Comply with all warnings and instructions marked on the equipment or specified in the manual supplied with the equipment. 4.If the operating instructions conflict with the safety information, please refer back to the safety information, as you may have misunderstood the operating instructions.
18.Please ensure timely ventilation in case of a prolonged use or printing huge amounts of documents in a poorly ventilated room. 19.In standby status, the product will automatically enter into the power saving (sleep) mode if it does not receive any job order for a while (such as 1 minute); and it can realize zero power consumption only if it has not been connected with any external input power supply. 20.
networked standby if all wired network ports are connected and all wireless network ports are activated. 31.Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits. 32.This Class B digital apparatus complies with Canadian ICES-003. 33. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the back of this equipment is a label that contains, among other information, a product identifier in the format US: VFCFA01A5103M .
The manufacturer of this product is: Zhuhai Pantum Electronics Co.,Ltd., No.3883, Zhuhai Avenue, Zhuhai, Guangdong, China 519060. A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative. This product satisfies the Class B limits of EN 55032 and safety requirements of EN 60950.
1.Before Using the Printer 1.1.
Drum component USB Interface Cable Power Cord CD Quick Setup Guide Pantum Warranty Note: Note: • The Pantum Warranty may not be attached in some regions. 1.3.
< 1 Cover of automatic document feeder This is used to remove the paper jammed in scanning for the ADF. 2 Feed tray of automatic document feeder Indicate printer status to conduct set operation. 3 Exit tray of automatic document feeder Prevent originals scanned from falling off. 4 Cover of scanner Open the cover of scanner to place the scanned originals on its glass plate. 5 Output Bin For storing the printed paper. 6 Front USB interface This is used to scan to an U-disk without a computer.
Rear View 1 LINE interface (only for machine with the fax feature.) Telephone line interface, used for connection of this product to the telephone circuit. 2 EXT. interface (only for machine with the fax feature.) Extension interface, used for connection with external extension telephone. 3 USB Interface For connecting product to computer with USB cable. 4 Network Interface For connecting product to network with network cable. 5 Power Interface For connecting product to power with power cord.
consumables are not covered by the scope of warranty. • Toner cartridge appearance may differ because of multiple volume and models, so the schematic diagram is only for your reference. 1.5.Control Panel 1.5.1.Overview of control panel The layout of the printer control panel is shown below: Control panel without the fax feature No. Name Functions 1 LCD Display Display operation interface and product information. 2 Copy Button Press this button to enter into copy mode.
Scroll through the menus and options . 13 Down Decrease 1 copy on the ready interface of Copy mode. 14 Status Light Indicate the status of printer. (Please see Chapter 1.6). Control panel with the fax feature No. Name Functions 1 LCD Display Display operation interface and product information. 2 Numeric keyboard Dial or input letters, numbers or characters. (Please see Chapter 1.5.2). 3 Fax Press this button to enter into the Fax mode.
Menu Open the main menu of control panel 15 Back Return to the previous menu. 16 Contacts This is used to enter quickly the Phone Book option under Fax mode. 17 UP Scroll through the menus and options . Increase 1 copy on the ready interface of Copy mode. Scroll through the menus and options . 18 Down Decrease 1 copy on the ready interface of Copy mode. 19 Status Light Indicate the status of printer. (Please see Chapter 1.6). 1.5.2.
2 Green indicator normally on Printer is ready 3 Green indicator blinks Operative modes of Print, Copy, Scan, Fax and others 4 Orange indicator blinks Low toner warning • Toner cartridge error (uninstalled ink cartridge, unmatching ink cartridge, invalid toner cartridge) • Drum unit error (the drum units are not installed, not compatible or come to the end of their service lives.
2.Paper and Print Media 2.1.
This may be due to incorrect operation, inappropriate temperature and humidity, or other factors beyond the control of Pantum. Before purchasing large quantities of print media, make sure that the print media meets the specifications specified in this User Guide. 2.2.Special Paper This printer supports using the special paper for printing. Special paper includes: label paper,envelope, transparent film, thick paper,carton paper, thin paper.
Usage Paper Size Top and bottom margins (A) Left and right margins (B) A4 5mm(0.197inch) 5mm(0.197inch) Letter 5mm(0.197inch) 5mm(0.197inch) A4 5mm(0.197inch) 5mm(0.197inch) Letter 5mm(0.197inch) 5mm(0.197inch) Printing Scan 2.4.Loading Paper Note: • Printer appearance may differ because of various models and functions, so the schematic diagram is only for your reference. 2.4.1.Loading into the Automatic Feeder Tray 1.Slide out the automatic feeder tray from the printer. 2.
Note: • Do not overly squeeze the "paper length guide" and "paper width guide", otherwise it could easily lead to deformation of paper. 3.Before loading paper, please unfold the stacked paper to avoid a paper jam or feed error, and then load the paper into the tray print-side down.The automatic feeder tray can be loaded up to 250 pages, 80g/m² paper. 4.Raise the output tray to avoid the printed paper from slipping and falling, or immediately remove the printed document after the printing is complete.
Note: • It is recommended that you raise the output tray to prevent the paper from slipping and falling after printing. If you choose not to raise the output tray, we recommend that you immediately remove the printed paper from the printer. • If more than 250 pages (80 g/m²) are put inside the auto feed tray at one time, paper jam or paper feed failure will be led to. • If carrying out single-sided printing, please make sure that the side to be printed (the blank side) is face down. 2.4.2.
4. Put a flat printing medium into the manual feed tray with both hands. Note: • The printer will enter manual feed mode automatically when you put papers inside the manual feed tray. • Please put one printing medium inside the manual feed tray each time and put in another piece after finishing printing. • Put the printing medium inside the manual feed tray with the printing side up; the top of paper should be put inside first. 5.
Steps of Use: 1) Lift up the scanner cover. 2) Load the manuscript face down. 3) Align the manuscript to match the appropriate paper size. Note: • If the manuscript does not match with any size marker, please align the upper-left corner of the manuscript with the arrow. • Make sure there is no document in the ADF. If a document is detected in the ADF, it will be more preferential than that on glass platen.
4) Close the scanner cover gently. Note: • Please put the paper or document on the scanner glass after the glue, ink or correction fluid are completely dried. • Rough textured, uneven, oil stained and extremely smooth paper will make printing effect poor. • Please make sure that there is no dust, fluff, etc. on the paper. • Paper shall be put on a flat surface and stored under a cool and dry environment.
Note: • The ADF supports feeding 50 pieces of paper at most that should be fed one by one.
3.Driver installation and uninstallation 3.1.Driver installation based on Windows system • Before installing the drive, you need to learn about printer model by printing printer information page out and check the product name (please refer to Chapter 12.4 for printing methods). • In case of covering the installed driver, the installation language cannot be changed. Please uninstall the printer driver and then install the driver of new version.
1. Turn the power of printer and computer on. 2. Connect the computer to wired network. 3. Connect network cable to the network interface of printer, to make sure the printer is connected to computer network (please refer to Chapter 4 for network setup). 4. Insert the installation CD companying with the printer in the CD driver of computer and operate Autorun.exe installation program. 5.
Note： • If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again. • If you want to install printer driver in the name of host, please tick the “Printer Name” you need to connect and “Install the printer from the list with a hostname”. • If IP address or host name is added manually, you need to know the IP address of the printer connected or host name.
5. Select “Yes, I want to configurate the printer's wireless network” on the wireless setup window popped out, and operate according to the prompts to set up the printer to wireless network (please refer to Chapter 5.1.1 for setup method). 6. After wireless network setup succeeds, the installation program will search for printer automatically, and it may take a while. 7. Select the printer needs to be connected and click “Next”.
Note： • If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again. • If you want to install printer driver in the name of host, please tick the “Printer Name” you need to connect and “Install the printer from the list with a hostname”. • If IP address or host name is added manually, you need to know the IP address of the printer connected or host name.
5. Select “No, the printer has been connected to wireless network” on the wireless setup window popping out, and then click “Next”. 6. The installation program starts to search for printer automatically, and it may take a while. 7. Select the printer needs to be connected and click “Next”.
Note： • If the printer you need to connect is not in the list of printers searched, please click “Refresh” to search again. • If you want to install printer driver in the name of host, please tick the “Printer Name” you need to connect and “Install the printer from the list with a hostname”. • If IP address or host name is added manually, you need to know the IP address of the printer connected or host name.
3.2.1.Driver installation Mac 10.11 is taken as the example in the following operation. The information on your computer screen may differ because of multiple operating systems. 1. Turn the power of printer and computer on. 2. Insert the CD companying with printer in the CD driver of your computer, and double click Pantum X Series installation package. (X in Pantum X Series represents product model.) 3. Click “Continue”. 4. Read licensing agreement and then click “Continue”. 5.
6. Click “Install”. 7. Input computer password and click “Install Software”. 8. Click “Continue Installation” on the prompt window popping out. 9. The system will finish driver installation automatically. • If USB cable is used to connect the computer and Wi-Fi model, the window to prompt wireless network setup will pop out during driver installation process, as shown in the diagram above. Click “Yes” to set up the wireless network of printer with wireless network setup tool (refer to Chapter 5.1.1).
3. Click button to select “Add Printer or Scanner”. 4. Select printer and then select the corresponding printer mode from the “Use” menu popping out. 5. Click “Add”. 3.3.2.Addition in wired network connection mode 1. Turn the power of printer and computer on. 2. Connect the computer to wired network. 3. Connect the network cable to the network interface of printer, and make sure the printer is connected to the computer network (Please refer to Chapter 4 for network setup). 4.
disconnected first before adding the printer. • AirPrint printer is named after the ending of "AirPrint".
4.Wired network setup (applicable to wired network models) In case printers support wired network printing, they can be connected to network to control printer to print in wired network mode. 4.1.Set IP Address The IP address of the printer may be automatically obtained through DHCP function or set manually. 4.1.1.Automatic Setting DHCP automatic setting function is enabled by default on the printer. 1.Connect the printer to the network through a network cable and complete the startup preparation work. 2.
5.Wireless network setup (applicable to Wi-Fi models) Wireless network connection type is divided into basic structure mode and Wi-Fi Direct mode. If you have problems with wireless network setup, please refer to Chapter 5.3 Wireless Network Setup FAQs. Basic structure mode: connecting to a wireless device via router 1. Access point (wireless router) 2. Wireless network printer 3. Computer connecting to access point via wireless network 4.
Note： • The SSID you selected should be consistent with the SSID of access point (wireless router) connected to your computer. • If the wireless network list is empty, please check if the access point (wireless router) is on, or if the computer is within the wireless network scope, and then click “Refresh” to search again. • If the SSID you need to connect is not in the SSID list searched out, please tick “Enter SSID Manually” to set up it manually (refer to Step 3.2.) 3.
2. Make sure the printer is in ready state. Note： • If the printer is in sleep mode, it can be woken up by pressing any key on the control panel of printer. 3. Press the “Wi-Fi key” on the control panel of printer for more than 2s until the blue Wi-Fi indicator of printer blinks, and then release pressing. 4. Press the WPS key on access point (wireless router) within 2min and then release it. 5.
4. Select printer SSID on direct interface to launch a connection invitation. 5. Press “OK key” to confirm connection when the panel lead to prompts whether to connect to start Wi-Fi Direct connection. Note： • In case of auto connection mode, the mobile device will start to connect automatically after initiating connection invitation without panel confirmation. 5.2.2.2.Connection method of wireless client that does not support Wi-Fi Direct function (input password to connect) 1. Turn on printer power. 2.
6.Web server You can manage printer setup via the embedded Web server. 6.1.Visit the embedded Web server 1. Turn on the power of printer and computer. 2. Connect the printer to network to ensure that the printer is connected to the network where the computer is connected to (please refer to Chapter 4 or Chapter 5 for network setup method). 3. Input the IP address of printer in the address bar of Web browser to visit the Web server imbedded in printer.
IPv4 address of the printer is divided into DHCP auto assignment and manual setting, and the DHCP auto assignment function is on by default. You can set up the IPv4 address of printer manually to set up fixed IPv4 address for the printer. 1. Turn on printer power to connect printer to network. 2. Log in the embedded Web server (please refer to Chapter 6.1 for login method). 3. Click “Settings” – “Network settings” – “Protocol Settings” – “Wired IP Configuration”. 4.
I. Set up SMTP client 1. Click “Settings” – “Network settings” – “Protocol Settings” – “SMTP”. 2. On SMTP page, input SMTP server address, set up the mailbox login name and password and then click “Apply”. II. Add recipient address 1. Click “Settings” – “Machine settings” – “Address Book” . 2. Click “Add”, input recipient address and then click “Apply”. III. Set up email notification 1. Click “Settings” – “Machine settings” – “E-mail Notification”. 2.
server name. 1. Log in the embedded Web server (please refer to Chapter 6.1 for login method). 2. Click "Settings", "Machine Settings" and then "FTP Address Book" to enter the setting interface of FTP address book. 3. Click "Create" to pop out a window as below and set relevant parameters; after settings completed, and then click "Apply". 6.2.3.4.
7.Print 7.1.Print Function You can set the print function through "Start"-"Devices and Printers"- select corresponding printer- right click – set print function in "Printing preferences". Some functions are as follows: Functions Diagram Automatic Two-Sided Printing Collate Print Reverse Print N-in-1 Poster Print(for Windows Operation System only) Zoom Print Custom Size Note： • Windows 7 is taken as example in the above description.
Note： • For precautions on loading paper, see Chapter 2. • For the type of media to be printed with the automatic feeder tray, see Chapter2.1. 7.4.2.Printing with manual feed tray When you put papers in the manual feed tray, the printer will enter manual feed mode. Note： • Manual feed mode means that papers will be fed from the manual feed tray first if there are papers being put inside it. • Generally, the manual feeder tray is used to print on special paper, such as envelopes, transparencies, etc.
4. Install the duplex unit in the printer. 7.5.2.How to carry out auto duplex printing 1.Open the print job to be printed from the application (such as a Notepad). 2.Select Print from the File menu. 3. Select printer of the corresponding model. 4. Single click “Preferences” for printing setup. 5. Select the “Duplex” in “Basic” tab and then select “Long Edge” or “Short Edge”.
6. Single click “OK” to finish printing setup. Click “Print” to realize auto duplex printing. 7.6.Fine mode printing The Fine mode is applicable to engineering drawings and fine lines printing. Set up fine mode in the basic page of printer preference . After setup, fine printing mode can be realized. 7.7.Mute printing If the Mute Printing is set, the printing noise will be reduced but the printing will slow down to some extent.
2. Right click printer and select “Printer properties” in the pull-down menu. 3. Enter the “Secondary Settings” option. 4. Tick “Mute printing” and click “Ok” to finish setup. 5. Open the printing work from the App, select a printer of the corresponding model and then set up printing according to needs. 6. Click “Print” to realize mute printing. Note： • Printers with LCD control panel can be set to mute printing with keys on control panel directly, please refer to Chapter 12.1.5 . 7.8.
8. Copying 8.1. Copying function Copy Common copying ID card copying Instructions Multipage Print a multi-page document to a piece of paper. Clone Print several identical images to a piece of paper. Poster Print a one-page original to pieces of paper. Collated copy Collate copies of an original. Duplex copying It supports manual duplex copying for originals. Image quality Set the definition mode to improve the copying effect. Intensity Adjust deep-light copying effect by setting intensity.
Auto: default mode, applicable to text and image originals. Text + image: applicable to originals with mixed text and image. Image: applicable to original image. Text: applicable to original text. Note: • The image quality mode supports “automatic” mode only after “poster” and “collated copy” are set. 8.4.2.Intensity Adjust deep-light copying effect by setting intensity. This printer supports "Manual Adjustment" and "Auto Adjustment" in color intensity.
Note: • "Multipage” and “resizing function” cannot be set at the same time. 8.4.5.Clone Through setting on clone feature, you may print multiple original images on one piece of paper. Copying with the ADF and the glass platen are both supported. The clone copying includes 3 modes: 3x3： 2x2： Note: 4X4： • The “clone” and “resizing function” cannot be set at the same time. 8.4.6.Poster Poster setting enables the printing of one piece of original document on several pieces of paper.
Closed: 8.4.8. Manual duplex copying You may use the glass platen or the ADF for duplex copying. The followings are examples of copying with the ADF. There are 4 modes in total for duplex copying: 2QH VLGHG ĺ 2QH VLGHG 2QH VLGHG ĺ 7ZR VLGHG 7ZR VLGHG ĺ 2QH VLGHG 7ZR VLGHG ĺ 7ZR VLGHG 8.4.8.1. Steps of duplex original copying 1) Put an original into the ADF with its front upward and its top fed first; meanwhile, make sure there are some paper in the carton.
5) After completion of copying one side, put the paper into the entrance as shown in figure (without turnover or rotation). Note: • If the turnover prompt on panel times out, the machine will execute one-sided copying automatically. 6) Press "Start" to begin copying the other side. 8.4.9.Paper setting Select the paper size and paper type of original copying in Paper Settings menu. Paper dimension: A4, Letter, B5, A5, A6, Executive, Legal and Folio.
Whole page up-down Half page up-down Half page left-right A5 left and right Position: Half page up-down: default mode; put ID card at “orange left half area” of glass platform. Half-page up and down, half-page left and right or A5 left and right: put the ID card in the "blue area" in glass platen. Note: • After setting, the arrangement mode can keep valid before startup; after startup, the arrangement mode will recover to default setting. 8.5.2.Intensity For intensity setting, see 8.4.2. 8.5.3.
9. Scan This printer provides two types of scan: "Push Scan", which means scanning through the printer’s Control Panel operations; "Pull Scan" which means scanning through PC terminal scanning the application. Before scanning, please be sure a printer driver has been installed in the computer. 9.1.Pull Scan You may scan with the scanning application in PC via USB, wired or wireless connection. Please be sure the printer has been properly connected before scanning. 9.1.1.
9.1.2.1. Office Software (Word and Excel) Operation Steps: 1) Open the Office software (Word or Excel). 2) Keyboard shortcuts: Alt+I+P+S to open the application’s window. 3) Click on "Device" option and select TWAIN Scan, click the “Custom Insert” button below. 4) After the window pops up, set the scan information in the right list of "Basic Setting" and "Advanced Setting". Click on "Scan" and start scan.
If you desire to change a scanning port, please click "Port" at the lower part of above picture to select a scanning port, as shown below: 9.1.2.2. Photoshop Operation Steps: 1) Launch Photoshop, click on "File" – "Import" on the top left corner and select TWAIN Scan, as is shown below: 2) After the window pops up, please refer to Step 4 of 9.1.2.1 to see the specific operation steps. 9.1.3. WIA Scan Driver 9.1.3.1. WIA1.0 Scan (Windows XP / Windows Server 2003) 1.
3) Click on "Device" and select WIA Scan,click the “Custom Insert” below. 4) The prompt window as is shown below, set the scan information. 5) Click on "Adjust the Scanned Image Quality" on the bottom left corner of the above picture, the advanced properties interface will pop up, then users can set the scan; After finishing the settings, click on the "OK" button, then "Scan" button to start scan.
2. Photoshop Operation Steps: 1) Launch Photoshop, click "File"- "Import" on the top left conrner and select WIA Scan, as is shown below: 2) After the window pops up, please refer to Step 4 and Step 5 of 9.1.3.1. to see the specific operation steps. 9.1.3.2.WIA 2.0 Scan (Windows Vista / Windows Server 2008 and later versions) Operation Steps: 1) Click on "Start"- "All Programs"- "Device and Printer" on the left bottom of the desktop.
2) When the pop-up window appears, select the printer you want to use, and right click the mouse. 3) Click on "Start Scan" in the above option bar.
4) After the window pops up, set the scan and click "Scan" on the bottom right corner and start scan. 9.2.Mac System Scan 9.2.1.ICA Scan 9.2.1.1.Open ICA via "Print and Scan" Operation Steps: 1) After installing the printer driver, click "System Preferences" icon on the bottom left corner of the computer desktop. 2) After the window pops up, click on "Print and Scan".
3) After the window pops up, click on "Scan". 4) Click on "Open Scanner" and the scan window will pop up.
5) Click on "Show Details" on the bottom right corner to set the scan parameters. 6) Click on "Scan" on the bottom right corner and start scan. 9.2.1.2. Call CIA through applications Operation Steps: 1) Click on "Finder" icon on the bottom left corner of the computer desktop, or use keyboard shortcuts command+shift+C to open the window. Find "Image Capture" in "Applications" (or conduct keyboard shortcuts command+shift+A to directly switch to "Applications") and click to launch the application.
2) After selecting the printer in the left list, set the scan parameters in the right list. Click on "Scan" on the bottom right corner and start scan. 9.2.2. TWAIN Scan Take Photoshop as an example.
2) After the window pops up, please refer to Step 4 of 9.1.2.1. to see the specific operation steps. 9.3. Push Scan This section is mainly to introduce how to scan files to PC, E-mail, FTP and USB with the printer's control panel. Note: • The one-page file scanned to PC, E-mail or FTP could be saved in PDF, TIFF or JPEG; if scanned to USB, it could be saved in PDF and JPEG.
6. Press "Menu" and then "OK" to enter the "Scan Setting" interface. 3UHVV Ÿ RU ź WR VHOHFW 6FDQ 7R RSWLRQV WKHQ SUHVV 2. 3UHVV Ÿ RU ź WR VHOHFW 6FDQ WR ( PDLO DQG SUHVV 2. EXWWRQ 3UHVV ³Ÿ´ RU ³ź WR VHOHFW ( PDLO $GGUHVV %RRN RU *URXS 0DLO DQG SUHVV 2. EXWWRQ 3UHVV ³Ÿ´ RU ³ź WR VHOHFW DGGUHVV RU JURXS DQG WKHQ SUHVV 2. EXWWRQ SUHVV 6WDUW EXWWRQ WR VWDUW VFDQ 11.
During the scanning, two ways are available to cancel the job: 1) Press "Cancel" button on the control panel to cancel the job. 2) Click Cancel button on the scan progress bar interface of the computer to cancel the job.
10. Fax 10.1. Connect Devices •“ ” port is used to connect fax with telephone line. •“ ”port is used to connect external telephone. Note: • it is recommended to use the traditional analog phone service (PSTN: Public Switched Telephone Network) in connecting telephone line. If a digital environment (for examples, DSL, PBX, ISDN or VoIP) used, please be sure to use a proper filter and configure digital settings correctly. For more information, please contact your digital service provider. 10.2.
2 Original Size You can select the desired size of the document to be Faxed. The available options are A4, Letter and Legal. 3 Luminosity You can adjust the luminosity of Fax documents manually or automatically. 4 Fax Name Input the fax name and save it. 5 Fax Number Input the fax number and save it. 6 Group Sending With the feature of multi-address sending, it supports inputting several numbers to be faxed one by one, with the ability of up to 20 fax numbers sent to at the same time.
Note: • In order to prevent damage to this product, do not use a manuscript with correction tape, correction fluid, paper clips or staples on it. In addition, do not load photos, small manuscripts or brittle manuscripts into the automatic document feeder. 10.3.1.2 Manual fax sending 1) Put an original on the glass platen or into the ADF (please see Chapter 2.5 for how to put an original). 2) Press the Fax button and use the number buttons to enter the Fax number.
• If the toner in cartridge runs low, the printing job of fax received may not be completed perfectly. Please replace with a new toner cartridge or find out the " Low in Toner, Continue to Print" option among the fax receiving setting options and then set it as "On" for continuous printing. 10.3.3.
10.4.1.Sending Fax with PC-Fax 1) Open the document to be faxed. 2) Click "File" and then "Print". 3) Select a printer named after the end of Fax and then click "Printer Properties"; next, set "Paper" and "Quality" of PC-Fax sending on the "Fax Settings" popup. 4) Click "Print" to present the "Send Fax" interface.
11.Mobile Print/Scan/Fax 11.1."Pantum" APP Pantum APP is a free application with mobile printing, scanning and faxing functions, allowing you to print or fax photos, files, pages and scan photos or files directly from mobile terminal. Your printer may not support all of above mentioned functions, so please select relevant function of Pantum APP for use according to your printer type. Please be sure the application has been installed and connected to wireless network properly before use. 11.1.1.
4. Select the function you want and then do relevant settings to meet your functional demands. Note: • If failure of operation, please check if your Android mobile device has access to the wireless network into which your printer is connected. • If the Android device cannot detect any printer, please inspect if power of the printer is turned on and if the printer is turned on. 11.1.3.2.For IOS Devices 11.1.3.2.1.Preliminary preparations 1. A printer that has wireless network function. 2.IOS mobile device.
4. Select the function you want and then do relevant settings to meet your functional demands. Note: • If failure of operation, please check if your IOS mobile device has access to the wireless network into which your printer is connected. If the IOS mobile device did not detect any printer, check whether the printer is powered on and the printer is turned on. 11.2.Mopria mobile print Mopria mobile print requires installing Mopria Print Service on the Android device.
1.Tap the "settings" of the Home Screen on Android mobile device, and select "print". 2.Set the "Mopria print service" as "ON". All other printing plug-ins should be shut down when you use Mopria mobile printing function. The printing steps may varied by applications, taking Adobe Reader as an example for explanation. 1. Turn on printer power. 2.Connect the Android mobile device with wireless network of the printer (Please refer to Chapter 5 for how to connect). 3.
Note: • For some mobile devices, NFC antenna may not be on their backsides. Before touching, please check the position of the NFC antenna of your mobile device. • If the mobile device is not installed with Pantum App, the Pantum App download link will pop out automatically. Try again after downloading and installing the App. 3. Select the content to be printed and set printing parameters according to needs. 4. Click print and the printer will start to print. 11.4.
12.General Settings This Chapter mainly introduces some general settings. Note: • The panel appearance may be a little different due to difference in type or function. All diagrams are only for reference. 12.1.System Settings 12.1.1. Ink saving setting You can select the save toner mode which can reduce toner consumption and reduce printing cost. When save toner mode is “on”, the printed color will be lighter. Save toner mode is “off” by default. 1) Press "Menu" to enter the menu setting interface.
12.1.3.Restore Factory Settings “Restore factory settings” is used to recover the default settings of printer. The printer will restart itself automatically after recovering factory settings. 1) Press "Menu" to enter the menu setting interface. 3UHVV Ÿ RU ź WR VHOHFW 6\VWHP 6HWWLQJ DQG WKHQ SUHVV 2. 3UHVV GLUHFWLRQ NH\ Ÿ RU ź WR VHOHFW WKH 5HVWRUH 6HW RSWLRQ DQG SUHVV 2. Note: • Factory settings of network printer can be recovered via embedded Web server (please refer to Chapter 6.
Set mute mode to realize low speed printing with low noise. When mute mode is “on”, printing will be in a low speed. This mode is “off” by default. 1) Press "Menu" to enter the menu setting interface. 3UHVV Ÿ RU ź WR VHOHFW 6\VWHP 6HWWLQJ DQG WKHQ SUHVV 2. 3UHVV GLUHFWLRQ NH\ ³Ÿ´ RU ³ź´ DQG VHOHFW ³0XWH SULQWLQJ´ RSWLRQ DQG SUHVV ³2.´ NH\ WR WXUQ RQ RII WKLV PRGH 12.1.6. Sound/volume (applicable to machine with the fax feature) You may set the up and down of sound/volume or shut down.
You can check or set network status via network setting. 1) Press "Menu" to enter the menu setting interface. 3UHVV GLUHFWLRQ NH\ ³Ÿ´ RU ³ź´ DQG VHOHFW ³ 1HWZRUN 6HW´ RSWLRQ 3) Press “OK” key to set “Wired network setting”, “wireless network setting” and “Wi-Fi Direct”. 12.3.Network Information You can check the network status through Network Information. 1) Press "Menu" to enter the menu setting interface. 3UHVV GLUHFWLRQ NH\ ³Ÿ´ RU ³ź´ DQG VHOHFW ³1HWZRUN LQIRUPDWLRQ´ RSWLRQ DQG SUHVV ³2.´ NH\ WR
mail, FTP address and Wi-Fi hotspot. Note: • The product report above is the most complete version, and may be different from the product report of model that you actually use. " 12.5. Residual amount of toner You may check the current residual amount of toner in cartridge with the printer's control panel. 1) Press "Menu" to enter the menu setting interface. 3UHVV Ÿ RU ź WR VHOHFW 5HVLGXDO $PRXQW RI 7RQHU 3) Press "OK" to enter and check the residual amount. 12.6.
13.Routine Maintenance Note: • Printer appearance may differ because of various models and functions, so the schematic diagram is only for your reference. 13.1.Cleaning the Printer Note: • Please use mild detergents. • Some parts of the printer are still in high temperature within a short time after use. To prevent burns, please don't directly touch places labled with high temperature warning in contact with internal components after opening the printer's front or rear cover. 1.
5. Wipe the LSU lens of printer gently with dry lint cloth. 5. Open the auto feed tray and wipe the pickup roller gently with dry lint cloth. Note: • the machine with the ADF should be regularly cleaned, removing dirt on the top cover of the ADF. Please wipe the place as shown in figure with a soft cloth.
13.2.Toner cartridge and drum component maintenance 13.2.1.About toner cartridge and drum component component 1.Cartridge, use and maintenance of the drum assembly. Please use the original toner cartridge for better printing quality. Please pay attention to the following items while using the toner cartridge: • Please keep the toner cartridge in a dry and dark place.
2. Open the front cover and then remove the laser toner cartridge along the guide rail. 3. Press the blue button on the left side of drum component with left hand and lift the toner cartridge handle with right hand at the same time to take the toner cartridge out. 4. Open the package of the new toner cartridge and hold the toner cartridge handle to shake it left and right for 5 – 6 times, so that the toner inside can be uniformly dispersed. 5. Pull the seal out and take the toner protection cover out.
8. Close the front cover. Replace the drum assembly steps are as follows: 1.Power off the printer. 2. Open the front cover and take the laser toner cartridge out along the track. 3. Press the blue button on the left side of drum component with left hand and lift the toner cartridge handle with right hand at the same time to take the toner cartridge out. 4. Open the package of new drum component, take the protection device of drum component, and put the drum component on a horizontal table.
5. Install the drum component along the inner track to finish installing toner cartridge. 6. Take the drum component with toner cartridge installed and install it inside the printer along the inner track of printer to finish installing. 7. Close the front cover.
14.Troubleshooting Please read this section carefully. It may help you to solve common problems encountered during the printing process. If the problems persist, please contact Pantum Aftersales Service Centre. Prior to handling common problems, first check that: • The power cord is connected correctly and the printer is powered on. • All of the protective parts are removed. • The toner cartridge is installed correctly. • The paper is correctly loaded into the tray.
5. Take the laser toner cartridge out along the track. (For the purpose of preventing printing quality from affecting by the exposure of photosensitive drum, please put the laser toner cartridge inside the protection bag or warp it with thick paper). 6.Gently pull the jammed paper out. 7. After taking out papers jammed, install the laser toner cartridge again and close the front cover, then the printer will recover printing. 14.1.2.
3.Open the fuser door using the handles on both sides. 4.Gently pull the jammed paper out. 5. Close the back cover after removing the paper jammed. 6. Install a new toner cartridge and then close the front cover; then, the printer will recover printing automatically. 14.1.3.Duplex Unit Jam 1.Remove the duplex printing unit from the back of the printer.
2.Remove the jammed paper from the duplex unit. 3.If the paper does not come out along with the duplex unit, open the tray and remove the jammed paper directly from the bottom. 4. After taking papers jammed out, install the duplex unit back and inspect other parts to the product. If it can be ensured that there are no jammed papers, open and close the front cover and then the printer will recover printing automatically.
3. After removing the paper jamed, close the top cover and then the printer will be back to the ready state. 4.If it is difficult to remove the paper jammed, please try to open the scanner cover and remove it from the pressing block. 14.2.Software Failure Problem Solution The printer icon will not be displayed in the “Printer and fax” folder. Reinstall the printer driver. Ensure that the USB interface cable and the The printer is in Ready mode but it will not perform any print job.
Toner Low (this prompt is displayed together with the standby picture alternately.) The toner in cartridge runs low. Please replace with a new toner cartridge. Please replace with a new toner cartridge or find out the " Low in Toner, Continue to Print" option among the fax receiving setting options and then set it as "On" for continuous printing. As the toner is low, it is not available to accept the printing job (this prompt is displayed together with the standby picture alternately.
• Data cable of the device is not properly connected. Problems in scanning Scanning error • The scan driver is installed incorrectly. • Ensure proper connection of the data cable. • Reinstall the scan driver. • The LCD screen prompts error messages. Paper feed failure • The printer paper isn't put properly. Please install printing medium correctly; please print with manual feed tray if special printing medium is used to print. • The print media is beyond the usage specification range.
Black vertical stripes • The reflective glass of the laser inside the printer is dirty. • Clean the feed path of printer. • The paper path is dirty. • Clean the scanner or the platen glass. • If black vertical stripes appear when copying or scanning, the scanner or the platen glass may be dirty. • Scanner Light bulb has smudges. • The scanner is damaged. • The print media that does not meet usage specification is used. For example, the media is damp or too rough.
Note: •Failures above can be improved by cleaning or replacing toner cartridge. Please contact customer services center if the problem can still not be solved. 14.5. Fax faults Trouble Type Fault phenomenon Solution • If you cannot hear the dialing tone after picking up the receiver, please check the connection of all telephone lines between the fax and the wall-mounted socket. The dialing tone cannot be heard.
15.Menu Structure With the help of menu structure of this printer on the panel menu, you may know and set various functions. The steps of printing are as follows: 1) Press "Menu" to enter the menu setting interface. 3UHVV Ÿ RU ź WR VHOHFW ,QIRUPDWLRQ 5HSRUW 3UHVV 2. DQG WKHQ Ÿ RU ź WR VHOHFW 3ULQW 0HQX 6WUXFWXUH 4) Press "OK" to print.
16.Product Specifications Note: • Specification values vary slightly from printers with different models with different functions ,and product specifications vary from different countries and regions. • These values are based on the initial data. For more information about the latest specifications, please visit: www.pantum.com. 16.1.
Microsoft Windows XP/ Windows Vista/ Windows 7/ Windows 8/ Windows 8.1/ Windows 10/ Windows Server 2003/ Windows Server 2008/ Windows Server 2012（32/64 Bit） Mac OS 10.7/10.8/10.9/10.10/10.11 Linux (Ubuntu 12.04/ Ubuntu 14.04) Operating System Versions higher than IOS 6.0 (excluding IOS 6.0) Android 4.0 and higher versions NeoKylin (Loongson V6.0 Build0341050) Hi-speed USB 2.0 Communication interface IEEE802.3 10Base-T/100Base-Tx IEEE802.11b/g/n (support WPS) 16.2.
Other Copy Functions "ID copy, Receipt copy, N-up copy, Clone copy" 16.4.Scan Specifications Scan Type Flatbed+ADF Flatbed: 216×297mm Maximum Scan Size ADF: 216×356 mm Chromoscan Yes Scan Output Function Scan to E-mail, PC, FTP and USB 16.5.Fax specification (applicable to machine with a fax) Fax Type Black-and-white Modem Speed 33.
