IP Wireless / Wired Camera IP Camera User Manual (For Windows OS)
IPCAM User Manual Content 1 Product Overview .................................................................................................... 4 Product pack age ................................................................................................................................. 4 1.2 Product Characteristics ...................................................................................... 4 1.1 2 3 Device apprearance and interface installation ......................................
IPCAM User Manual 8 7.8 Upgrade Device firmware ............................................................................................................. 50 7.9 Backup and restore setting ........................................................................................................... 50 APPENDIX.................................................................................................................................................. 51 8.1 8.2 8.2.
IPCAM User Manual 1 Products overview IP Camera is a IP integrated camera solution. For the user based on the local network ( LAN ) and wide area network ( WAN ) remote video surveillance products provides a clear, high integration, low cost solution. Integrated network and web service function, the shooting of the video can be transmitted through the network to any place, you simply through web browser can readily access live video.
IPCAM User Manual 2 Device appearance and interface 2.1 Device appearance Build-in Sensitive hole HD Glass Lens Microphone Built in sound Infrared LED Picture 1 Device appearance 1. Sensitive Hole: According to outside of light decide whether open infrared LED 2. Infrared LED 3. Lens :CMOS Sensor .You can turn around the lens manually to adjust the focus range 4.
IPCAM User Manual 2.2 Device interface I/O Alarm input/output WIFI antenna RJ-45 Ethernet Port DC5V Power adapter Audio output Picture 2 Device interface LAN : RJ-45/10-100 Base T DC5V : 5V/2A Power supply I/O PINS: 1)Output(GND) 2)Output (+5V) 3)Alarm input 4)Input (GND) (you can see 3.5.6 For more information) RESET Picture 3 BUTTON Reset Button RESET BUTTON: Press and hold down the RESET BUTTON for 5 seconds.
IPCAM User Manual 3.1 Install hardware You should install your IP Camera's hardware according to the following step in order to make sure the IP camera can work properly. Especially, pay attention to IP camera's installation environment. 1) IPCAM. Plug DC adapter with IP camera I.Note: Please use Dc adapter which is the standard configuration of IP camera. Using DC adapter without any certificate, may destroy IP camera.
IPCAM User Manual to use because It is suitable for different LAN NETWORK environment.
IPCAM User Manual 4) The device IP Address can be changed, but Its IP address should be at the same with PC's subnet. Device IP address can be changed by yourself Network server provide DNS server Address Picture 7 When we test IP camera and check whether it starts smoothly or it connects properly, we can operate in the Windows(START- RUN-CMD), and then input : ping 192.168.1.111 in the order windows.
IPCAM User Manual 3.2 Software installation Software installation It is very easy to install software. You just need to run installation programme then it can work properly. Please put CD in the PC driver and the CD will automatically run to the software installation interface: User manual Search tool in LAN G Min Exit Quick installati on gui de Open CD Open user manual Application Tool box Picture9 Software installation interface If no such an interface, please click And then find search.
IPCAM User Manual 4 Visit IP camera in LAN 4.1 Conne ction ways in LAN Picture 10 4.2 Connection between Several IP camera and router Search and set device IP address Please note before searching IP camera 1 Make sure IP camera has a good connection with power and n etwork.
IPCAM User Manual SIX Options Choose the IP Camera list and Click right mouse button, there are six options, Basic Properties, Network Configuration, Upgrade Firmware, Refresh Camera List, Flush Arp, About IP camera tool as shown Picture 12. Picture 12 Basic Properties There is some device information in the Bas ic Properties, such as Device ID, System Firmware Version, Web UI Version Picture 13 Network Configuration In this page, you can configure the Network parameter.
IPCAM User Manual IP address: Fill in the IP address assigned and make sure it is in the same subnet as the Subnet Mask: The default subnet mask of the equipment is: 255.255.255.0 Gateway: Make sure it is in the same subnet with PC IP address. Default Gateway address is 192.168.1.1 DNS:Server: IP address of IPS network provider. ( It also can view from network card local area connection status). As blows picture.
IPCAM User Manual Refresh Camera List Refresh camera list manually. Flush Arp Buffer When cable network and wireless network of the device both are fixed IP address. There is a problem you may encounter is can search the camera IP but can t open the camera web page.you may try to use flush arp buffer. About IP Camera tool You can view IP ca mera tool version and ActiveX version.. 4.
IPCAM User Manual Language options:you can choose operation language according to your demand Picture 18 Picture 19 When Users login in,they can view images.
IPCAM User Manual Picture 20 Picture 21 16
IPCAM User Manual 4.4 IP camera operation 4.41 For Visitor For example: if is bright ,the first route is at status of Detection(Only IE Broswer can view it) Buttom for taking picture Stop monitor video Open vedio Record Monitor audio Two way audio Picture 22 The right upper is status's indicator area which can show 9 IP camera status. When the button is gray, it means IP camera didn't connect. Green means IP camera has connected. Yellow means there is something wrong with connection.
IPCAM User Manual October 11, 2010.When use motion detection and checked Send Mail on Alarm. The name of the picture received in mailbox is like this: device id( Alias)_ Current time.jpg 4.42 For operator When login as operator, you can operate Pan/Tilt and adjust video parameter.
IPCAM User Manual 4.43 For Administrator When you login as administrator, you can set all parameters. Please click and enter into setting interface . View Device ID Dev ice Firmware Version and Device Embedded Web UI Version Check Device all kinds of status Carry on Settings a nd operation function Picture 24 Alias Settings: You can Input the new name as you like. Data &Time Settings: Data &Time Settings page. Users Se ttings: Eight accounts are acceptable for this system.
IPCAM User Manual 5 Visit IP Camera in internet 5.1 Connection way in Internet Picture 25 Related setting and login IP camera 1. If the network your IP camera using is using static IP, you just need to input this IP address and IP camera's port in the browser, then it can visit Ip camera. 2. If you are using ADSL to dial-up and surf on line, you should obtain IP Camera Current WAN IP Address or configured DDNS.
IPCAM User Manual We take" Nur8555M " from " Xinxiang" 's router as example A.According to router's manual, we get Router's IP is 192.168.1.,1 B.Login in router,: Input 192.168.1.1 in the browser. Find the status of Router and find Router's WAN( In this exa mple, WAN'S IP is 116.24.235.122 As shows Picture 27. Picture 27 No w you can visit IP Cam from Internet. What you should do is to Input correct IP address . For example: Http:// 116.24.235.122:8999 Note : Make sure the Port's UPNS is av ailable.
IPCAM User Manual Our products have be en configured the DDNS services, of course, you ca n also apply for the domain name in registration website for one of your ow n domain name to configuration. For e xample: www.dyndns.org Factory DDNS DDNS You need fill in DDNS and port. for example: (http://c0001.topipcam.org;8999/). The browser will jump to IP camera s login page. .
IPCAM User Manual The input device user name and password to login to equipme nt If input domain name , but can't open IP camera in the browser, s uch as the situation is as blows Please open the device a nd check sta tus of IP camera in the local area ne twork, confirm whether UPNP function and DDNS is successful or not.
IPCAM User Manual If you use T PLINK router, please refer to these instructions Through the upnp automa tic mapping port to the network: input router IP a ddress in the browser (such as "http://192.168.1.
IPCAM User Manual Input IP camera's IP address, for example: (http://c0001.topipcam.org;8999) Picture 37 " Search" Picture 38 enter your account and password on the login page as shown By default s username is: admin and no password.
IPCAM User Manual Option for operation language Click and on-line video view Picture 41 Open IP camera successfully Picture 42 26
IPCAM User Manual 2 Now we take Android system device as example: Open menu and firstly open the browser, and input IP camera 's IP address in the browser ,for example: (http://c0001.topipcam.org 8999) Open menu Input IP camera's username and password and click " sign in", and then enter into browser model to choose login-in interface. Picture 44 6.2 INSTALL CLIENT-SIDE SOFTWARE TO ACCESS IPCamera There are many client software support IP camera, several third-party software support our IP cameras too.
IPCAM User Manual 2.3 Choose the USB connection model on your cellphone; you can see the SD driver in 2.4 Copy the ipcamera.apk into SD card. 2.5 Disconnect the device 2.6 The ipcamera application will be show up on the home screen after you successfully installed. Software operating processes First ensure that the Internet open WIFI connection, the search in the Play, in The Googl Android application reecam.
IPCAM User Manual You can edit the camera, modify camere configuration and delete camera operation.
IPCAM User Manual 2. The IPCamera setting process for iPhone iPad Firmware requirements: compatible with iPhone, iPod touch, and iPad. Systerm requirements: Requires iOS 4.2 or above, You can download the genuine software (ipcamera.app) form the App Store: http://itunes.apple.
IPCAM User Manual Fill in the domain address or IP address Completed please click here Fill in the Http port of the camera, login user name and password, click "next" to open the camera Preview video click on the next save Save the camera added Selected camera to view images Click image to expand more cameras operating functions 31
IPCAM User Manual 7 Other setting 7.1 Network Setting 7.11 Basic Network Settings Http Port: In most cases, you can leave this value as 80, however, if your Internet Service Provider blocks this port, you may switch to another port number such as, 85 8080 8888 9000 Etcs. (Range from 0 to 65535, pay attention to the same segme nt of multiple devices must se t up differe nt port. The port t can t have any conflict with other software or equipment a.
IPCAM User Manual Figure 54 As Administrator to Login camera, open wireless LAN Settings page, fill in every Setting used. For example: as shown in belows Pls click the scan buttom twice.
IPCAM User Manual Double click to choose Fill the encryption and routers and key in the same way Figure 56 7.
IPCAM User Manual Picture 58 3) Unplug the RJ45 from IP camera .Use laptop or other devices which are with wifi function( include smart phone,ipad and so on) searching the SSID you defined on proccess 2,then make a connection. Picture 59 Click wireless network and check the link status of ip camera. Please note IP address of your connected laptop must be the subset of your ip camera .if not, please reset the ip address of your laptop manually.
IPCAM User Manual 2 Enter ip address in the browser Enter user name and password in the login interface Picture 62 Picture 63 36
IPCAM User Manual 7.2 Multi-Device Settings Add cameras in LAN In the Multi-Device Settings page, you can see all devices searched in LAN. The 1 St Device is this device in default. You can add more cameras list in LAN for monitoring. This Web software supports up to 9 Device Host and Http Port more cameras in the same way.
IPCAM User Manual Picture 66 7.3 MSN Settings Fill in your MSN account and password, then add account which need to receive S MSN list (Picture 67 Aplly for MSN account and passworf for IP cam Add about 10 MSN Accout Picture 67 First login and click "add contacts " choose messaging address" Add Contact ,then fill IPCAM s MSN account in "instant ,click next then send offers.
IPCAM User Manual Figure68 Ne xt Figure69 .
IPCAM User Manual Picture 71 You can input the IP address to browser then can browse ip camera as be low: Figure72 Attention:You should fill M SN account in IPCAM first. 7.4 DDNS Service Settings DDNS Service: The system supports protocols from some DDNS providers: Dyndns.org. System support DDNS ,such as topipcam.org peanut shell 3322.org DynDNS provided IP.
IPCAM User Manual User and Password: the user name and password used when applying for the domain name.. (details : 4.3.2) 7.4.1 DDNS Host: the Domain Name Factory DDNS Device had distributed one DDNS to every product.which was sticked the bottom of the product. Such as manufacturer had already give every device a DDNS address which is unique.
IPCAM User Manual Note: the third party domain name is the realization of analytical way, input the domain in the browser, it will keep this string of characters. If the port of the device isn t 80, then nee d to add colon and port number .For example: http://well888.dyndns.org:8999 7.5 Mail and FTP Service 1 Configure the E-mail box to receive and send mails. The E-mail box is used for receiving the images sent after alarm and the system IP address after successful dial-up..
IPCAM User Manual Gmail also set as the same: It only needs you to fill in correct SMTP Sever address, user and password. Picture 78 Mail notes Internet IP address: In this option, When Internet IP and port have changed, IP Will be sent via mail. 1 Can not connect to the server 2 Network Error. Please try later 3 Server Error 4 Incorrect user or password 5 The sender is denied by the server.
IPCAM User Manual FTP Server of LAN as below: 1. Create an account 2. Step by step setting until finish it.
IPCAM User Manual 3.
IPCAM User Manual 5. Picture 86 6. Set up and complete testing is successful,when it alarms, IP camera will upload pictures to the FTP server Settings of main directory path (as shown ) Picture 87 FTP Se rver: the FTP server address. FTP port: the port usually is 21 FTP Mode: support standard(POST) mode and passive(PASV) mode. Upload Image Now: it will upload image now when checkbox is not checked. When checked, you can input upload interval(Seconds) 7.6 Motion Detection .
IPCAM User Manual IO linkage alarm output: relay closure, external alarm device bega n to alarm Send E-mail alarm informa tio Transmit pictures to the FTP server, and can set the time inter val of sending pictures; 1) Alarm tim e Settings Only in the alarm period, detection device to alarm will only ha ve alarm action. All the time (not check the schedule ) also can alarm within specified time.
IPCAM User Manual Picture89 IO Linkage on Alarm Enable IO linkage on alarm,Pin1 will output +5V when alarm triggered, and output LOW when alarm release automatically. Switch on/off buttons control Pin1 output manually. Send Mail on Alarm Sent picture and mail inform to customer s e-mail after alarmed.(firstly you should finish the Mail Service Settings.) Tick: send to your setted mails Picture 90 Upload Image on Alarm Enable upload image on alarm and set upload interval(Seconds).
IPCAM User Manual After Setting up later ,when have the alarm ,the image will send to designa ted ema il and FTP server Picture 91 REC automatically and save to PC When you enable motion detect and open the camera monitoring page on the PC. If there is an alarm triggered, REC will start automatically for several seconds and save to the PC.
IPCAM User Manual 7.7 IP camera's Time & Date setting and PTZ Setting If IP camera connected with Internet, it can automatically check the time & date via running NTP Server. And need to choose properly IP camera's Time zone. Otherwise it need PC Time to check IP camera time & Date. Pre-set and Speed of PT. The huger the Number is, The slower it will be. 7.
IPCAM User Manual 8 APPENDIX 8.1 REGISTER AND APPLY FOR DDNS SERVICE 1 Users use DDNS management system first time.Users need to apply account to manage and inquire the domain state. Step1: enter http://www.dyndns.com/ and Create Account.( Fill in Domain Name .dyndns.
IPCAM User Manual Figure99 Step3: After a minute, you will receive an E-mail from DynDNS Support and it will give you a confirmation address (e.g. https://account.dyn.com/eml/createconf/lILHMZHRje5oF_6YXTYv1A Figure100 Step4: Open the link to active your Domain Name as below.
IPCAM User Manual . Figure101 Step5: Check all the DDNS services,we choose the 14-day-trial Figure102 Step6: Click the link,and user will see as below.
IPCAM User Manual enter your information Figure104 Step7: No w you obtained a Dynamic Domain Name(Figure 105),and can use it in the DDNS Se rvice Se ttings(details: 7.
IPCAM User Manual 2.For DDNS which is applied successfully, you can fill in the IP CAMERA. When set successfully, the status of IP of IP will be shown as blows: picture 106 picture 107 3 How to set DDNS on line? The first way Menu start - run > Input CMD Clink enter via.
IPCAM User Manual Through the PING command, this dynamic domain name ca n be back in the ne twork response information. It proves tha t the domain name has been online. If the domain name update not success! Possible reasons: (1) DDNS parameter is not correct. (2) may cause: DNS address configuration is wrong. 8.
IPCAM User Manual From the following picture, we can view tha t "Ipcam" local IP address is WAN IP Address is open in the player http://well888.dyndns.org:8999 Picture http://192.168.1.
IPCAM User Manual Picture 117 Open the Internet play position: User Size: 640X480 Picture 118 As shown in the following picture, It can see the ipcamera send video s treaming forma t 58
IPCAM User Manual Picture 119 8.3 Frequently Asked Questions Note:1) Any question you would meet, please check Network connections firstly. 2)Check the working status revealed by the indicators on the network server, hub, exchange and network card. If abnormal, check the network connections. 8.3.1 I have forgotten the administrator username and/or password. To reset the administrator username and password, Press and hold down the RESET BUTTON for 5 seconds.
IPCAM User Manual you are set up port forwarding properly. ( consult your router is documentation for more information ) .If none of these seem to be the problem, it is also possible that your ISP is blocking inbound connections to port 80 many IPSs have done this because HTTP server on an alternate port (such as 8080). 8.3.4 No Monitoring picture It has four reasons Images of the abnormal fa ctors: 1 If its not use Directx function and lead to not normal to display the color image.
IPCAM User Manual 8.3.6 Why popThis prompt only appeared in the case of using multiple cameras. Enter the Multi-Device Settings page(login as administrator) to check the Device setting is correct or not. When one of the multiple cameras disconnected, the color changed to yellow and pop- Picture 121 8.3.7 access the IPCAM in the internet? There are some reasons: 1 ActiveX controller is not installed correctly(see more details:5.1.4). 2 The port IPCAM used is blocked by Firewall or Anti-virus software.
IPCAM User Manual transmission channel require higher t 2. Confirm the power supply normally. First, check whether power indication light turn on or not, If it is on,then check the yellow light on RJ45 Port (power indication light) and green light (network indication light) are on or not.If they are on,so power supply and cable runs normally. 3. Confirm all the firwall and antivirus software are close.
IPCAM User Manual 8.6 Technical Parameters IP CAM ITEM Image Sens or Lens NIP-02BGPWA2 Mage sensor 1/5" Color CMOS Sensor Display 640 x 480 (300K Pixels) Lens f:3.6mm, F:2.4 (IR Lens) Mini.illumination 0.
IPCAM User Manual FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
