Operating Manual

Thank you for choosing our doorbell. For better use of this product,
please read operating manual carefully before installation,
and according to the manual for correct installation and use.
1. Non-professionals should not open or maintain it himself to avoid
damaging the sophisticated electronic components.
2. Please try to avoid installation the device under rain, over expose
to sun or close to metal.
3. The actual remote control distance depends on the working
environment as they are affected by interference.
Solving potential problems
Transmitter Structure
Receiver, transmitter, screw, double-sided adhesive sticker,
12V 23A battery
Modern and Stylish design
45 polyphony melodies
4 Volume adjustable (mute included)
Over 150 meters operation range (open air)
Easy to install and use
Learning code function
Low power consumption
Waterproof transmitter (some model)
IP44
Voltage of plug-in receiver AC 85-260V (US,EU,UK,AU)
Selectable ring tone
45melodies
Volume range 0-100dB, 4 level
Voltage of battery type receiver 3x1.5V AAA batteries
(Model P,N)
1.Receiver suddenly can’t get signal from transmitter.
Reason 1: Low power battery in transmitter. The less power in trans-
mitter, the shorter range is.
Use a fresh new battery or plug receiver into a nearer outlet.Solution 1:
Page 5
Reason 2: Plug of receiver is loose.
Re-plug your receiver.Solution 2:
Reason 3:Reset the receiver by accident so that transmitter is not paired
with receiver any more.
Re-pair receiver with transmitter as below.Solution 3:
How to re-pair:
1. Press and hold the button for changing volume for 3-4 sec.
2. At the same time bring the transmitter closer to the receiver, and hold
down its button for a 3-4 sec. together.
This way transmitter gets re-pair with receiver.
2.
Short operating range
Reason: There are too many obstacles like walls, metal doors between
receiver and transmitter
Solution: Test operating range before installation and change location.
Working frequency 433.92MHZ
Model:Q
Model:Q
Model:P
Model:188
Model:189
Model:188
Model:189
Flash light
Product size
:b) Transmitter installation method 2
Please prepare electric drill, screwdrivers
1. Find the hole on transmitter back cover, use slotted screwdriver
to push into the hole.
2.
Make marks of location on wall.
3. Make holes in the wall with electric drill. Then insert back cover
with screws(provided in the package).
4. Finally, put back front case with PCB board.
2. For DC receiver: Plug in batteries, then you can choose whether to
hang it up or just put it on desk.
1. For AC receiver: Just plug receiver into standard outlet in the room,
then it will work. You can choose melody you want.
3.
For Transmitter: Please first test if the operating range you choose
is working or not.
:a) Transmitter installation method 1
use double-side adhesive sticker to fix transmitter cover on the wall.
music
choice
volume
control
volume
control
music
choice
open from here
open from here
coding button
indicator light
flash light
indicator light
flash light
coding button
NOTE：
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE：
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF exposure compliance statement:
This device has been evaluated to meet the general RF exposure
requirement
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.