Smart Fabric Lamp (Instruction Manual)
Language EN --------------------------------------------- 02-21 DE --------------------------------------------- 22-41 1
Contents Notice & Features .............................................. 03 Packing List .............................................. 04 Installation Steps ........................................... Control Box .............................................. 13 ............................ 14 ........................................ 15 Quick Mode Configuration(EZ mode) .............................. 16 AP (Access Point) Mode Configuration ...............................
Notice 1.For your safety, please entrust professional installation and maintenance. 2.The ambient temperature for normal use is -30℃~ 50℃. If it exceeds this range, the product life will be adversely affected. 3. Please check if there is any damage after unpacking. If so, please contact your online service for replacement. If there is a defect during transportation,do not use the damaged lamp to avoid electric shock. 4. Please turn off the power before installation, and then perform wiring installation. 5.
Packing List Cloth cover 1X Rod A 1X Remote control 1X Chassis 1X Rod B 1X Rod C 1X Internal tooth ring 2X Adaptor 1X Rod D 4X Rod E 1X Plastic head screw 1X Light strip 1X Note: The shapes of the cloth cover and base accessories are for reference only, please refer to the actual product.
Installation Steps Rod E Rod D Rod D Step 1: Each section of the round pipe is connected in turn, as shown in the figure.
Light strip B A2 Light strip Step 2: After wrapping the light strip around the circular tube into a serpentine shape, buckle both ends of the light strip to the circular tube, as shown in the figure.
Internal tooth ring Rod B A3 Rod A Chassis Step 3: From bottom to top, install parts one by one, as shown in the figure.
Cloth cover NOTE: The shape of the cloth cover can be divided into round, square and hexagon according to the different styles purchased. Please refer to the actual product! A4 Step 4: A round hole of the cloth cover is inserted into the thread of the round pipe.
Internal tooth ring A5 Step 5: Using the Internal tooth ring, screw in the rod B to clamp the bottom of the cloth cover, as shown in the figure.
Step 6: Install the finished product in step A2 on the rod of A5, as shown in the figure.
A7 Step 7: Pull up the cloth cover until the cloth cover is topped on Rod E.
A8 Step 8: On the rod E, use Plastic head screw to lock the upper part of the cloth cover,as shown in the figure. Step 9: Connect the adapter power supply, then it can be powered on.
Controlling By Control Box On/Off button:Short press to turn on/off the floor light, long press 5 seconds,the LED controller will start Wi-Fi config. Bright/speed ajustment:Short press to switch speed circularly, long press to switch bright circularly. Please Note : 1.This product is only suitable for 2.4G Hz network. 2.The remote control needs to be aimed at the sensor head.
Remote control precautions 1. Do not expose this product directly to a humid environment. 2. Do not expose this product to excessively high temperature environments. 3. Please keep it out of reach of children. 4. If there is a problem, please refer to the user manual and/or contact your online service. Warning: 1. This product is for indoor use only. 2.
Setting the APP Step 1: Scan the QR Code or search"Smart Life"or"Tuya Smart"on App store or Google Play to download and install the APP foriOS/Android. The mobile phone system version needs to be Android 5.0 and iOS 9.0 or above.
Step 2: Run "Smart Life"or"Tuya Smart"app on your phone, then tap "sign up" to create an account with Email address (if you already had one, please log in),and verify your account with verification code which has sent to your email. Step 3: Log in your account and follow the App instructions to create a "Family" and later follow below instructions to add devices to your "Family". Quick Mode Configuration(EZ mode) 1.Before connecting,please make sure your smart phone is connecting with your home Wi-Fi(2.
AP (Access Point) Mode Configuration 1.Before connecting,please make sure your smart phone is connecting with your home Wi-Fi(2.4GHz)successfully. 2.To connect in AP mode,the strip lights needs to be set to blinksSlowly.
How to set light as rapidly flashing? (Ez Mode) Step 1 :Power on device. Step 2 :Hold the power button for 5S. Step 3 :Confirm LED Strip is now rapidly flashing. Floor light How to set light as slowly flashing? (Ap Mode) Step 1 :Power on device.
Step 2: Hold the power button for 5S. Step 3 :Confirm LED Strip is now rapidly flashing. Floor light Step 4 :Operate again:Hold the power button for 5S until light is slowly flashing. Floor light How to connect floor light to Amazon Alexa / Google Assistant ? You can learn the detailed instruction on "Me->More Services" page of the APP.Tap the corresponding service to learn more and how to set up.
20
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Inhalt Bekanntmachung & Eigenschaften - - - - - - - - - - - - - - - - - - - - - - - - - 22 Packliste - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23 Installationsschritte - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24-31 Steuerung über die Kontrollbox - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 32 Vorsichtsmaßnahmen und Funktionen für die Fernbedienung & Fernbedienungsfunktion - - - - - - - - - - - - - - - - - - - - -
Bekanntmachung 1.Werden Sie Ihre Sicherheit, bitte professionelle Installation und Wartung, Richtungsinstallation und Wartung. 2. Die Umgebungstemperatur für den normalen Gebrauch beträgt -30℃~ 50℃. Wenn diese Reichweite itprozniert ist, wird das Produktleben nachteilig beeinträchtigt. 3. Bitte prüfen Sie nach dem Auspacken, ob Beschädigungen vorhanden sind. In diesem Fall wenden Sie sich bitte an Ihren Online-Service, um einen Ersatz zu erhalten.
Packliste Stoffdecke 1X Stab A 1X Fernbedienung 1X Chassis 1X Stab B 1X Stab C 1X Innenzahnring 2X Adaptor 1X Stab D 4X Stab E 1X Schraube mit Kunststoffkopf 1X Lichtleiste 1X Hinweis: Die Formen der Stoffabdeckung und des Basiszubehörs dienen nur als Referenz, bitte beziehen Sie sich auf das tatsächliche Produkt.
Installationsschritte Stab E Stab D Stab D A1 Stab D Stab D Stab C 25 Schritt 1: Jeder Abschnitt des Rundrohrs wird der Reihe nach verbunden, wie in der Abbildung gezeigt.
Lichtleiste B A2 Lichtleiste Schritt 2: Nachdem Sie den Lichtstreifen um das Rundrohr gewickelt haben, Serpentinenform, beide Enden des Lichtstreifens an der Rundrohr, wie in der Abbildung gezeigt.
Innenzahnring Stab B A3 Stab A Chassis Schritt 3: Installieren Sie die Teile von unten nach oben nacheinander, wie in der Abbildung gezeigt.
Stoffdecke Notizen: Die Form des Stoffbezugs kann je nach gekauftem Stil in rund, quadratisch und sechseckig unterteilt werden.Bitte beachten Sie das jeweilige Produkt! A4 Schritt 4: Ein rundes Loch des Stoffbezugs wird in das Gewinde des das Rundrohr.
Internal tooth ring A5 Schritt 5: Mit dem Innenzahnring die Stange B einschrauben, um die Unterseite der Stoffabdeckung, wie in der Abbildung gezeigt.
A6 Schritt 6: Installieren Sie das fertige Produkt in Schritt A2 auf der Stange von A5, wie in der Abbildung gezeigt.
A7 Schritt 7: Ziehen Sie die Stoffabdeckung hoch, bis die Stoffabdeckung auf der Stange E . liegt.
A8 Schritt 8: Verwenden Sie auf der Stange E einen Kunststoffkopf Schraube zum Verriegeln des Oberteils der Stoffabdeckung, wie in gezeigt die Figur. Schritt 9: Schließen Sie das Netzteil an liefern, dann kann es sein eingeschaltet.
Steuerung über die Kontrollbox Bitte beachten Sie: 1.Dieses Produkt ist nur für . 2,4-GHz-Netzwerke geeignet. 2.Die Fernbedienung muss auf den Sensorkopf gerichtet sein. Weniger als 16 Fuß Ein/Aus-Taste: Kurz drücken, um das Bodenlicht ein- / auszuschalten, 5 Sekunden lang drücken, der LED-Controller startet die Wi-Fi-Konfiguration. Helligkeits-/Geschwindigkeitsanpassung: Kurz drücken, um die Geschwindigkeit kreisförmig umzuschalten, lange drücken, um die Helligkeit kreisförmig zu wechseln.
Vorsichtsmaßnahmen bei der Fernbedienung 1. Setzen Sie dieses Produkt nicht direkt einer feuchten Umgebung aus. 2. Setzen Sie dieses Produkt keinen Umgebungen mit übermäßig hohen Temperaturen aus. 3. Bitte bewahren Sie es außerhalb der Reichweite von Kindern auf. 4. Wenn ein Problem auftritt, schlagen Sie bitte in der Bedienungsanleitung nach und/oder wenden Sie sich an Ihren Online-Service. Warnung: 1. Dieses Produkt ist nur für den Innenbereich geeignet 2.
AN AUS Klicken Sie hier, um die Lichter ein-/auszuschalten. Klicken Sie hier, um in den Musikmodus zu wechseln. Klicken Sie hier, um abzuspielen oder zu pausieren. Klicken Sie hier, um den automatischen Szenenmodus aufzurufen. AUTO GESCHWINDIGKEIT+/-Passen Sie die Ausführungsgeschwindigkeit im Szenenmodus an. Passen Sie den Szenenmodus an. MODUS+/Helligkeit +/Klicken Sie hier, um die Helligkeit der Lichter anzupassen.
Schritt 2: Führen Sie die App "Smart Life" oder "Tuya Smart" auf Ihrem Telefon aus, tippen Sie dann auf "Anmelden", um ein Konto mit einer E-Mail-Adresse zu erstellen (falls Sie bereits eine hatten, melden Sie sich bitte an) und bestätigen Sie Ihr Konto mit dem gesendeten Bestätigungscode an Ihre E-Mail.
Konfiguration des AP-Modus (Access Point) 1. Bevor Sie eine Verbindung herstellen, stellen Sie bitte sicher, dass Ihr Smartphone erfolgreich mit Ihrem Heim-WLAN (2,4 GHz) verbunden ist. 2. Um eine Verbindung im AP-Modus herzustellen, müssen die Lichtstreifen auf langsam blinken eingestellt werden. (Sie können die detaillierte Anleitung im Abschnitt "So stellen Sie das Licht als langsam blinkend" ein.
Wie stelle ich das Licht so schnell blinkend ein? (Ez-Modus) Schritt 1: Gerät einschalten. aus>3s ein>10s Schritt 2: Halten Sie den Netzschalter 5 Sekunden lang gedrückt. Schritt 3: Bestätigen Sie, dass der LED-Streifen jetzt schnell blinkt. 2 Mal pro Sekunde Stehleuchte Wie stelle ich das Licht als langsam blinkend ein? (AP-Modus) Schritt 1: Gerät einschalten.
Schritt 2: Halten Sie den Netzschalter für 5S gedrückt. Schritt 3: Bestätigen Sie, dass der LED-Streifen jetzt schnell blinkt. 2 Mal pro Sekunde Stehleuchte Schritt 4: Erneut betätigen: Halten Sie den Netzschalter für 5S . gedrückt bis das Licht langsam blinkt. 1 mal pro 3 Sekunden Stehleuchte So verbinden Sie die Stehleuchte mit Amazon Alexa/Google-Assistent? Sie können die detaillierte Anleitung auf der Seite "Ich->Weitere Dienste" der APP erfahren.
40
Dieses Gerät entspricht Teil 15 der FCC-Bestimmungen. Der Betrieb unterliegt den folgenden zwei Bedingungen: (1) dieses Gerät darf keine schädlichen Störungen verursachen, und (2) dieses Gerät muss alle empfangenen Störungen akzeptieren, einschließlich Störungen, die einen unerwünschten Betrieb verursachen können. HINWEIS: Dieses Gerät wurde getestet und entspricht den Grenzwerten für ein digitales Gerät der Klasse B gemäß Teil 15 der FCC-Bestimmungen.