KR2201WR 智能通断器说明书 注意事项 请仔细阅读本说明书。 本产品只能在室内使用。 本产品不防水,请勿将本产品暴露于滴水或溅水等任何危险的环境。 本产品只能由成人安装。 请勿安装在任何热源附近。 请勿将本产品与调光器一起使用。 请勿在完全封闭的灯具中使用本产品。只能在开放式灯具中使用本产品。 如果本产品重量比需要更换设备的重量重,则有可能会降低照明设备和灯座的机械稳定 性,并可能损害触点与灯的固定位。 电击危险:请在干燥环境中使用。 请勿湿手安装本产品! 接线示意图 *请勿带电接线 ————————————————— ———————————————— —————— —————
一、无线遥控功能操作说明(RF 功能) *红色指示灯表示“智能通断器”进入配对遥控器的状态。 手动开关模式说明 无需遥控器,按一下对码按键“智能通断器”打开,再按一下对码按键“智能通断器”关闭。 自锁模式对码说明 (遥控器一个按键,按一下打开,再按一下关闭。该模式适用于 1 个遥控器按键控制 1 个“智能通断器”) 设置方法:按下“智能通断器”上的对码按键 2 次,红色指示灯闪烁后点亮;按下遥控器上需要配对的 按键,当红色指示灯闪烁后熄灭,自锁模式设置成功。 互锁模式对码说明 (设置一个按键只能打开,另外一个按键只能关闭。需要至少两个按键以上的遥控器。该模式适用于一个 遥控器控制多个“智能通断器”。) 设置方法:按下“智能通断器”上对码按键 3 次,红色指示灯闪烁后点亮;按下遥控器需要设置为打开功 能的按键(例如按键 A)红色指示灯闪烁后,继续按遥控器上需要设置为关闭功能的按键(例如按键 B)红 色指示灯闪烁,互锁模式设置成功。 点动模式对码说明 (同一个按键,按住打开,松开关闭。) 设置方法:按下“智能通断器”上的对码按键 4 次,红色指示灯闪烁后点亮;按下遥控器上需要配对的按 键,当红色指示
2. 重置“智能通断器”: 长按“智能通断器”上的对码按键 6 秒以上直到绿色指示灯快速的闪烁 3.
配网成功后可以在 APP 首页界面看到新添加的设备,此时“智能通断器”绿色指示灯常亮 ————————————————— ———————————————— —————— —————
过天猫精灵智能语音设备控制“智能通断器” 在这之前你需要做好以下准备工作: “智能生活”app可以正常的控制“智能通断器”。 拥有一个正常可以使用的天猫精灵智能音箱。 手机安装“天猫精灵”app并已经绑定天猫精灵智能音箱。 ————————————————— ———————————————— —————— —————
三、产品参数 输入电压:交流 AC 90V-250V 50/60Hz 最大负载电流:10A 最大负载功率:阻性负载 2200W (AC220V) 感性负载 500W (AC220V) 容性负载 200W (AC220V) 白炽灯 2200W 节能灯 300W LED 灯 300W 遥控(RF)工作频率:433MHz 遥控(RF)距离:空旷地区大于 25 米 ————————————————— ———————————————— —————— —————
User Manual Safety Warning This device is for indoor use only. This device should not be exposed to dripping or splashing water or any danger Sources. This device should only be installed by adults. Do not install near any heat sources. Do not use this device with dimmers. Do not use this device in totally enclosed luminaires. Use this device in open luminaires only.
Operation Note: The red indicator light indicates that the "smart switch" has entered the state of pairing the remote control. Manual switch mode description Without the remote control, pressing the setting button "smart switch" will turn it on, and pressing the setting button "smart switch" will turn it off. Latch Mode Setting Description (Press the remote control to turn it on, then press it to turn it off.
*The indicator light(Led) shows green that the device is matching the WIFI function First of all : 1. Power on the smart switch and make sure that the phone is connected to the Wi-Fi network in the 2.4GHz frequency band; turn on the phone’s Bluetooth. 2. Make sure that the device, mobile phone, and router are close to each other. 3.
After the smart switch is successfully connected to Wi-Fi,LED is always on, you can see the newly added device on the home page of the Smart Life APP.
then Jump to the device information page, where you can change the name of the device, and you can see the details of the third-party controlled APP supported by the device, select the APP you need to connect, such as Alexa, click the icon to enter the binding interface, and then press The page prompts the operation.
*Scan the QR code to view the electronic manual ————————————————— ———————————————— —————— —————
20C