BTH070N Bluetooth stereo headset User’s manual
Contents Brief introduction…………...…………………………..…....1 Before use……………………………………………………..1 1. Overview…………………………………………………...……1 2. Charging for headset..……………………………………………2 Getting started……..…………………………………………3 1. Turning on/off the headset …………....……………………......3 2. Wearing the headset.......................................................................3 3. Pairing/Connecting…….…….............................……………..….5 1) Pairing headset with Bluetooth cell phone via Bluetooth……..….
Welcome to use this Bluetooth stereo headset, BTH070N. Please read this user’s manual carefully before use. Brief introduction BTH070N is a comfortable and fashion music Bluetooth headset. Nice necklace design as well as magnet on main body and earbuds are well for easy carrying or wearing. BTH070N can be used on various environments because it have passed IPX4-rated sweat-proof. The headset will vibrate when receivers an incoming call for built-in vibrator so all calling wont be missing.
1 Right ear plug 6 2 Left ear plug 7 NFC zone 3 Magnet button 8 USB charging jack 9 Microphone /LED 4 :volume up/previous song 5 : volume down/next song : MFB button 2. Charging for headset The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low power, the headset emits “Battery low” every 5 minutes and the red LED flashes. Please recharge the battery of the headset.
Getting started 1. Turning on/off the headset Functions Operation Prompt tone Turning on Press and hold about 2.5 Power on seconds until blue LED flashes Turning off Press and hold about 2 Power off seconds until red LED flashes Remark: In order to save power, the headset will turn off automatically if no devices can be connected after long time. 2. Wearing the headset A.Choose the suitable size earbud according to your ears. B .
C. Separate magnet button gently if you want to take down the headset from your neck. D. The cable length can be adjustable Step 1:Like picture 1 show, one hand hold the magnet button,the other hand push cable to the magnet button; Step 2:Like picture 2 show,one hand hold the magnet button,the other hand pull cable to increase cable length between magnet button,then the necklace length will shorten.
E.Right/Left ear plugs can be fixed on the main body via the magnet function when no need use of headset, at the same time it becomes a nice and fashion necklace for you. The headset also can be connected as below method: 3. Pairing/Connecting 1) Pairing headset with Bluetooth cell phone via Bluetooth Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled cell phone.
different models of cell phones. Please refer to your cell phone user’s manual for further information. The general pairing procedures are as follows: 1) Keep your headset turned off and within 1 meter of phone ; 2) Press and hold about 4 seconds until the red and blue LED flash alternately, and the headset emits”Pairing”.
Remarks: The pairing password of BTH070N is “0000”. So, the headset can only pair with a Bluetooth transmitter whose pairing password is “0000”. If pairing still fails after several tries, please refer to the Bluetooth transmitter’s user’s manual for further information. 3) Pairing headset with a Bluetooth cell phone via NFC BTH070N support NFC technology, it can quickly connect with Bluetooth cell phone via NFC.
3) Pairing headset with multi devices via Bluetooth The headset can connect with two Bluetooth cell phones at the same time. The general pairing procedures are as follows: 1) Pairing the headset with device one 2) Turn on the headset and make it enter pairing mode again, and pairing it with device two 3) Operate device one to connect with headset.
5.
Cancel mute During a call (microphone mute) Voice dial Standby mode (connected device) Redial the Standby mode last number (connected device) Warning: Excessive pressure from cause hearing loss. Long press about 1 seconds Mute off Short press and button simultaneously Double click button Voice dial Last number redial earphones and headphones can Note: When the volume is adjusted to max or min, you will hear one prompt tone.
3) Connect with two cell phones Functions Status of headset End phone call #1 During phone call #1, and answer phone phone 2 has incoming call #2 call Retain phone call #1 During phone call #1, and answer phone phone 2 has incoming call #2 call Switch call During call, one of phone call is retained End current call, During call, one of back to retain phone phone call is retained call 5.
6. LED indicator LED indicator Red and blue LED flashes alternately Blue LED flashes once every 2 seconds Blue LED flashes twice every 4 seconds Red LED flashes instead of blue LED Status of headset Pairing mode Not connected to device Connected to device Low battery 7. Factory Reset In the status of charging, long press button about 3 seconds and release it until the red and blue LED flashes simultaneously, you will hear “reset paired”.
Don’t scratch the surface with sharp things. Don’t use this product during strenuous exercise. It may get damaged by sweat. In case the product doesn’t function properly, send it to the store you bought it. The staff will help you to solve the problem FAQs 1.What does it mean when red LED flashes instead of blue LED? Battery is low power, need to be recharged. 2.Why is the red LED off when charging? a) Please make sure the charging device connect with headset well; b) The battery may dry up.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.