BTH033 Bluetooth stereo headset User’s manual
Contents Brief introduction…………...…………………………..…....1 1. Bluetooth wireless communication technology……………….…....1 2. About BTH033…………………………………………………...1 Before use……………………………………………………..2 1. Overview…………………………………………………...……2 2. Charging for Headsets……………………………………………3 Getting started……..…………………………………………4 1. Turning on/off the headsets…………………………………......4 2. Pairing headsets with Bluetooth devices………………………..….4 1) How to enter pairing mode………………….………………….
Welcome to use this Bluetooth stereo headset, BTH033. Please read this user’s manual carefully before use. Brief introduction 1. Bluetooth wireless communication technology Bluetooth is a standard of close range wireless communication technology that was drawn up by Ericsson, IBM, Intel, Nokia and Toshiba. With Bluetooth technology, we can achieve the highest transmission rate among cell phones, computers, printers, PDAs and other devices.
3) Easy to switch between the call and music, you will not miss the incoming call during listening to music. 4) Every time the headset is turned on, it will connect to last connected device automatically. Note: In order to complete to above function, the Bluetooth profiles of paired device must be same as the headset. And even though the paired device and the headset support the same Bluetooth profiles, functions may vary due to specification differences of the paired devices. Before use 1.
1 2 3 4 5 6 Built-in Microphone Multi-function button(MFB) Next song Pause/play Last song Line-in jack 7 8 9 10 11 12 LED indicator Charging jack Volume down Volume up Right speaker Left speaker 2. Charging the headset The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low power, red LED flashes twice and the headset emits three “Dong” tones every 30 seconds and the red LED flashes twice.
The way of charging as following: Using USB cable 1. Plug USB charging cable into the USB port of computer 2. Plug another side of USB cable to headset Red light on: Charging Red light off: Finish charging 3. It will takes about 2.5 hours to finfish charging Remarks: 1) The battery is recyclable. 2) Batteries (battery pack or batteries installed) shall not be exposed to excessive heat place, such as sunshine, fire or the like. Getting started 1.
2) Pairing the headset with a Bluetooth cell phone Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled cell phone. The pairing procedures are subject to different models of cell phones. Please refer to your cell phone user’s manual for further information.
1) Keep your headset and phone within 1 meter when pairing; 2) Make the headset enter pairing mode (Please refer to “How to enter pairing mode); 3) Turn on the Bluetooth transmitter. It will search for Bluetooth devices automatically and send a pairing request; 4) When the headset requests to enter a PIN No., the transmitter will response “0000” automatically; 5) After successful pairing and connecting, blue LED of the headset flashes twice every 4 seconds.
Remarks: After successful multi-pairing, the paired devices will remember each other, they will no need to pair next time. If the pairing information is deleted, please connect the mobile phone with the headset first and then turn on the Bluetooth transmitter, multi-connecting can be performed. For the cell phone supporting the HSP and A2DP at the same time. It may set up HSP and A2DP connection with the headset simultaneously. At this time, the Bluetooth transmitter may not connect to the headset. 3.
Transfer conversation to mobile phone Transfer conversation to headset Microphone mute Cancel mute Voice dial Redial the last number Remove paired list During a call Long press MFB for 2 seconds During a call Long press MFB for 2 seconds During a call Double click MFB During a call (microphone mute) Standby mode (connected device) Standby mode (connected device) Turned off Double click MFB Long press button for 2 seconds Double click MFB Press MFB and pause button for 8 seconds simultaneously, and r
Note: Not all the mobile phones support all the functions listed above. Please refer to your mobile phone user’s manual. Different function and prompt tone according to different mobile phone. When the volume is adjusted to max or min, you will hear one prompt tone. When pressing the answer button on some mobile phones, the call will be transferred to the mobile phone. You can switch the call to the headset by using the conversation switch button or through operating on the mobile phone.
If you want to remote control last/next song, pause/play, it needs your Bluetooth mobile phone or Bluetooth transmitter paired with the headset to support AVRCP profile, please refer to the user’s manual of your mobile phone or Bluetooth transmitter for further information. The Bluetooth will disconnect between headset and mobile phone automatically if you plug 3.5mm audio input, and the Line in is available in this time. 6.
8. Factory Reset In the status of turned off, long press MFB and pause button for 8 seconds simultaneously and release it until the red and blue LED on. 9. Resetting If the product work abnormally, you can plug 3.5mm Line-in or charging the headset so that to reset products. Care and maintenance Read the following recommendations carefully before using BTH033. Following these you will be able to enjoy this product for many years.
3. How far is the effective rang between the headset and mobile phone? According to the Bluetooth standard, the max available range of ClassII headset is 10 meters. It varies under different environment. 4. Why my mobile phone can not search and find the headset? The mobile phone will not find the headset if headset and mobile phone are not under the pairing mode. Make sure the headset is under the pairing mode and in the effective working range, and then the headset can be paired and connected. 5.
Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
