Manufacturer: Zhongshan Hot Mom Commodity Co., Ltd. Address: No.1, Julu Street, Fusha Town, Zhongshan, Guangdong Province, China Company website: www.hotmom-uk.
ELECTRIC BABY BOUNCER User Manual for Electric Baby Bouncer PLEASE READ THE MANUAL CAREFULLY BEFORE USING THE PRODUCT AND KEEP IT FOR FUTURE USE. FOLLOW INSTRUCTIONS IN THE MANUAL, AS WRONG USE MAY LEAD TO THE DANGER OF YOUR BABY.
Product Information Model: BB200 Product Name: Electric Baby Bouncer Product Dimensions: 61×68×63cm Input Voltage: 100-240V Input Current: 0.5A Output Voltage: 5V Output Current: 1A Frequency: 50/60HZ Rated Power: 3W (motor 2.5W + horn 0.4W + control circuit 0.1W) Bearing Weight: Below 9kg Applicable Age: 0-12 months Main Material: Aluminum, PA plastic Product Information Strict material selection, soft fabric, enjoying comfort and safety.
Parts List ① Pillow × 1, ② Remote control × 1, ③ Seat cloth × 1, ④ Adapter × 1, ⑤ Seat frame× 1, ⑥ USB cable × 1, ⑦ Base × 1 Note: For USB cable, one end connection to the mainframe is the port for DC cable, and the other end connected to the adapter is the USB port generally. * Read carefully and follow all instructions.
Assembly Instructions Assembly of baby bouncer seat frame ① Insert the end of the aluminum tube with a “round hole” into the port of body support. ② Lock the aluminum tube with the black plastic buckle, as shown in the figure. Round hole Port Black plastic buckle ① Insert the round hole position of the assembled body support into the position of the locking component in the round frame until the locking component protrudes from the round hole.
Assembly of baby bouncer base ① Insert the aluminum tube of the base into the main seat of the baby bouncer until the holes on both sides are aligned and overlapped. The aluminum tube on the other side can be installed with the same method. Round hole ② Install the screws on the two holes and lock them tightly, and lock the screws on the other side as well. The assembly of the base is completed.
Assembly Instructions Assembly/Disassembly of the base and seat frame Assembly: Align the seat frame and insert it to the joint of base. Disassembly:Lightly pull out the plastic sheet at the rear end of the joint between the seat frame and the base, and take out the seat frame upward at the same time. Plastic sheet Assembly/Disassembly of seat cloth and pillow ① Zip up the zipper between seat cloth and seat frame.
Seat angle adjustment ① Open the seat buckle outward as shown in the figure. ② Then hold the seat frame to adjust the required angle,and finally fasten the buckle. Seat buckle Use of safety belt Move your baby’s legs into the two sides of the triangle safety belt, adjust the tightness of the safety belt on both sides, and then fasten the safety buckle. Warm tip: To ensure your child’s safety, please always use the safety belt when your baby is lying in the baby bouncer.
Instructions for Use Button instruction Power button: press for power on , the indicator light will be on; press again for power off , the indicator light will be off. Timing button: the default status is “--”. Press the first time to display “**”, setting time for* minute(s). Press the second time to display“**”, setting time for * minute(s). Press the third time to display “**”, setting time for * minute(s).
Remote control Bluetooth switch button Baby bouncer power button Last one Next one Baby bouncer scope, five gears Note: The number of corresponding screen light on indicates the current gear number of the Baby bouncer (e.g.: 1 light on is 1 gear, 3 lights on are 3 gears). Timing button Power supply mode • 100-240V - 50/60Hz 0.5A AC power supply can be plugged into the DC port. • DC interface can be connected to a power bank.
WARNING AND REMINDING • To ensure the safety of your child, please read the manual carefully before using the product and keep it for future use. Follow instructions in the manual, as worng use may lead to the danger of your baby. • The product can only be assembled by adult. • The product is only for positioning use. Never use this as a means to transport your baby and do not move the baby bouncer when the product is being used. • Never use the product for an infant able to sit up, kneel up or climb up.
Before using the product, please check whether the voltage and power used are consistent with the product identification to prevent circuit overload. • Do not use accessories not supplied by the manufacturer. • Stop using the product immediately if it is damaged. • Remove the plastic cover before use. To avoid the suffocation hazard, please handle the plastic cover properly or keep it away from infant and children. • Do not place the product near fire, and avoid direct sunlight and strong heat source.
WARNING FALL Hazard: Babies have suffered skull fractures falling while in and from bouncers. Use bouncer ONLY on floor. NEVER lift or carry baby in bouncer. SUFFOCATION Hazard: Babies have suffocated when bouncers tipped over on soft surfaces. NEVER use on a bed, sofa, cushion, or other soft surface. NEVER leave baby unattended. To prevent falls and suffocation: ALWAYS use restraints. Adjust to fit snugly.
CAUTION The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver.
After-Sales Service Dear customers, Thanks for using Hot Mom’s products, and the product you purchased from our company is under warranty for one year from the purchase date. When applying for a warranty, you will need to present your warranty card or original proof of purchase. This warranty service does not apply to the following: A. Damage caused by improper use such as disassembling and modifying without permission; B.
Cleaning and Maintenance Cleaning 1. Wipe the baby bouncer base with a wet cloth and gentle cleanser, and dry it thoroughly after that. Do not use corrosive cleaners. 2. Cloth can be disassembled and washed, specifically: ◎ Cloth seat: First remove the seat cloth. If it is dirty, wipe it with wet cloth and soft soap and dry it.
List for Environmental Protection Purpose Declaration of hazardous substances According to Measures for the Administration of the Restricted Use of the Hazardous Substances Contained in Electrical and Electronic Products, the following part lists the names and contents of hazardous substances that may be contained in the product. *Note: The environmental protection service life of the integrated packing[e.g. lamp, battery] (consumables) is [e.g. 5 years].