Instruction IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE Please read the instruction of the swing carefully before using. If the swing is not operated according to the instructions, it may cause injury to the baby. Model No:CR010A Standard:EN12790:2009/EN16232:2013+A1:2018/EN71-1&-2&-3 Company name:Zhongshan City Cironbaby Co.,Ltd. Add:No.
Product summary 1、Home page 1 2、Introduction 2 General 2 Parts List 3 Install 4~ 7 3、Function Panel 8 Remote 8 MP3 9 Bluetooth 9 4、Cleaning and maintenance 10 5、Attention 11 1
Introduction General: Name Electric baby bouncer chair Model No. CR010A-1 Input voltage 100-240V~50/60Hz 0.3A Out voltage DC5V/1A Max. load capacity 9Kg Standard EN12790:2009/EN16232:2013+A1:2018 EN71-1/EN71-2/EN71-3 Production date See the package or product label WARNING 1)Power supply terminal must not short-circuit. 2)Never use the adapter provided not by the manufacturer, input voltage of adapter:100-240V~50/60Hz/0.3A MAX,Output voltage: DC5.8V/1A.
Introduction Parts List: Number Name Qty A Seat 1set B Mainframe base 1set C Canopy 1set Accessories:Instruction*1pc,Adapter*1pc, Remote controller*1pc。 C A B 3
Introudction Install details: 1)Insert the seat into mainframe base. 2)Fasten the toy bar to the seat. Disassembly the seat: Push the sheet metal in and lift the seat up.
Introduction Seat installation details: 1)Keep the same direction of seat D hole and mainframe base D iron shaft,then insert the seat into mainframe base,then rotate the seat left and right slightly,then press down the seat after alignment,then finish the seat installation. 2) WARNING: After completing the installation of the seat, please pull up the seat to ensure that it is well locked before using it.
Introduction Put baby in the seat,then fasten the seat belt,then cover the buckle bag well。 Power supply: 1) DC plug can insert into the DC power of 100~240V,50/60Hz, 0.3A. 2) DC interface can be connected by power bank. 3) Output voltage:5.8V,electric current:1A.Never use the adapter of other specifications. 4) Never use the adapter provided not by the manufacturer.
Introduction Seat angle adjustment: 1. Press the adjustment buttons on both sides of the joint to adjust the seat angle downwards. 2. To adjust the seat angle upwards, simply lift the rear end of the seat to adjust it automatically. 3. The seat angle is adjustable in three positions.
Function introduction Panel func�on: Remote receiver Power switch Speeds adjustment Music play/pause 8 30 15 Next tune/ volume adjustment Timing bu�on Remote func�on: Timer Power switch Music play/pause Timing Last music Switch inside music/Mp3 Next music USB Music USB Music VOL+ Volume up SLEEP Sleep mode VOL- Volum down STOP Stop MUSIC Timer VOL+ VOL- SLEEP 1 2 3 4 5 1 STOP 2 3 4 5 5 speeds op�on 8
Function introduction MP3 func�on: 1)Insert USB device into USB interface,then can play the music inside the USB device。 2)Pull out USB device then will play the music from the product when turn on the music bu�on。 USB interface Bluetooth func�on: 1)Turn on the bluetooth in the mobile phone to search the name of swing chair,the product will play the music inside the mobile phone a�er connect this bluetooth device.
Cleaning and maintenance The accessories of this product: toy bar, pillow, seat cloth can be cleaned with a damp cloth moistened with a flexible cleaning agent and left to air dry in a cool place.
WARNING 1.Never leave the child unattended. 2.Do not use this product once your child can sit up unaided or weighs more than 9 kg. 3.This product is not intended for prolonged periods of sleeping. 4.Never use this product on an elevated surface (e.g. a table). 5.Always use the restraint system. 6.Never use the toy bar to carry the reclined cradle. 7.To avoid injury ensure that children are kept away when unfolding and folding this product 8.Do not let children play with this product. 9.
FCC Requirement Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.